ASTM A1018/A1018M-04
(Specification)Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability
Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability
SCOPE
1.1 This specification covers hot-rolled, heavy-thickness coils beyond the size limits of Specification A 1011/A 1011M.
1.2 The product is available in five designations: Commercial Steel, Drawing Steel, Structural Steel, High-Strength Low-Alloy Steel, and High-Strength Low-Alloy Steel with Improved Formability.
1.3 This material is available only in coils described as follows:ProductSize Limits, Coils OnlyWidth, in. [mm]Thickness, in. [mm]StripOver 8 to 12, incl[Over 200 to 300]0.230 to 1.000, incl[Over 6.0 to 25]SheetOver 12 to 48, incl[Over 300 to 1200]0.230 to 1.000, incl[Over 6.0 to 25]SheetOver 48[Over 1200]0.180 to 1.000, incl[Over 4.5 to 25]
1.4 Sheet and strip in coils of sizes noted in are covered by this specification only with the following provisions:
1.4.1 The material is to be fed directly from coils into a blanking press, drawing or forming operation, tube mill, rolling mill, or sheared or slit into blanks for subsequent drawing or forming.
1.4.2 The material is not to be converted into steel plates for structural or pressure vessel use unless tested in complete accordance with the appropriate sections of Specifications A 6/A 6M (plates provided from coils) or A 20/A 20M (plates produced from coils). Plate produced in this manner is no longer governed by this sheet steel specification and since this material is now plate, the appropriate plate standard shall apply.
1.4.3 The dimensional tolerances of Specification A 635/A 635M are applicable to material produced to this specification.
1.4.4 Not all strength levels are available in all thicknesses. The user should consult the producer for appropriate size limitations.
1.5 The values stated in either inch-pound units or SI units [metric] are to be regarded separately as standard. Within the text the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A 1018/A 1018M – 04
Standard Specification for
Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled,
Carbon, Commercial, Drawing, Structural, High-Strength
Low-Alloy, and High-Strength Low-Alloy with Improved
1
Formability
This standard is issued under the fixed designation A 1018/A 1018M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.4.3 The dimensional tolerances of Specification A 635/
A 635M are applicable to material produced to this specifica-
1.1 This specification covers hot-rolled, heavy-thickness
tion.
coils beyond the size limits of SpecificationA 1011/A 1011M.
1.4.4 Not all strength levels are available in all thicknesses.
1.2 The product is available in five designations: Commer-
The user should consult the producer for appropriate size
cial Steel, Drawing Steel, Structural Steel, High-Strength
limitations.
Low-Alloy Steel, and High-Strength Low-Alloy Steel with
1.5 The values stated in either inch-pound units or SI units
Improved Formability.
[metric] are to be regarded separately as standard. Within the
1.3 This material is available only in coils described as
text the SI units are shown in brackets. The values stated in
follows:
each system are not exact equivalents; therefore, each system
Product Size Limits, Coils Only
must be used independently of the other.
Width, in. [mm] Thickness, in. [mm]
2. Referenced Documents
Strip Over 8 to 12, incl 0.230 to 1.000, incl
2
[Over 200 to 300] [Over 6.0 to 25]
2.1 ASTM Standards:
Sheet Over 12 to 48, incl 0.230 to 1.000, incl
A 6/A 6M Specification for General Requirements for
[Over 300 to 1200] [Over 6.0 to 25]
Sheet Over 48 0.180 to 1.000, incl
Rolled Structural Steel Bars, Plates, Shapes, and Sheet
[Over 1200] [Over 4.5 to 25]
Piling
A 20/A 20M Specification for General Requirements for
1.4 Sheet and strip in coils of sizes noted in 1.3 are covered
Steel Plates for Pressure Vessels
by this specification only with the following provisions:
A 370 Test Methods and Definitions for MechanicalTesting
1.4.1 The material is to be fed directly from coils into a
of Steel Products
blankingpress,drawingorformingoperation,tubemill,rolling
A 635/A 635M Specification for Steel, Sheet and Strip,
mill, or sheared or slit into blanks for subsequent drawing or
Heavy-Thickness Coils, Hot-Rolled, Carbon, Structural,
forming.
High-Strength Low-Alloy, and High-Strength Low-Alloy
1.4.2 The material is not to be converted into steel plates for
with Improved Formability, General Requirements for
structural or pressure vessel use unless tested in complete
A 751 Test Methods, Practices, and Terminology for
accordance with the appropriate sections of Specifications
Chemical Analysis of Steel Products
A 6/A 6M (plates provided from coils) or A 20/A 20M (plates
A 1011/A 1011M Specification for Steel, Sheet and Strip,
produced from coils). Plate produced in this manner is no
Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy
longer governed by this sheet steel specification and since this
and High-Strength Low-Alloy with Improved Formability
material is now plate, the appropriate plate standard shall
E 29 Practice for Using Significant Digits in Test Data to
apply.
Determine Conformance with Specifications
G 101 Guide for Estimating the Atmospheric Corrosion
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
2
A01.19 on Steel Sheet and Strip. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved April 1, 2004. Published April 2004. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2001. Last previous edition approved in 2003 as A 1018/ Standards volume information, refer to the standard’s Document Summary page on
A 1018M – 03a. the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A 1018/A 1018M – 04
Resistance of Low-Alloy Steels 5.1.4 Condition—Material in accordance with this specifi-
cation is furnished in the hot rolled condition. Pickled (or blast
3. General Requirements for Delivery
cleaned) must be specified if required. Material ordered as
pickled (or blast cleaned) will be oiled unless ordered dry,
3.1 Material furnished under this specification shall con-
form to the applicable requirements of the current edition of 5.1.5 Type of edge must
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.