iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3306-08a

(Specification)

Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service

Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service

SCOPE
1.1 This specification covers the requirements for ethylene glycol or propylene glycol base engine coolants used in automobiles or other light duty service cooling systems. When concentrates are used at 40 to 70 % concentration by volume in water, or when prediluted glycol base engine coolants (50 volume % minimum) are used without further dilution, they will function effectively to provide protection against freezing, boiling, and corrosion.
1.2 The coolants governed by this specification are categorized as follows:
Coolant TypeDescription  IEthylene glycol base concentrate IIPropylene glycol base concentrate IIIEthylene glycol predilute (50 vol %) IVPropylene glycol predilute (50 vol %)
Note 1—This specification is based on the knowledge of the performance of engine coolants prepared from new or virgin ingredients. This specification shall also apply to engine coolants prepared using glycol generated from recycled or reprocessed used coolant or reprocessed industrial-source glycol, provided that said glycol meets the requirements of Specification E 1177. Separate specifications (D 6471 and D 6472) exist for engine coolants prepared from recycled or reprocessed used coolant or reprocessed industrial-source glycol that does not meet the requirements established in Specification E 1177.
1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 2—This specification applies to automobiles and light duty service. Specifications D 4985 and D 6210 exist for heavy duty engine service.

General Information

Status
Historical
Publication Date
14-May-2008
ICS
71.100.45 - Refrigerants and antifreezes
Technical Committee
D15 - Engine Coolants and Related Fluids
Drafting Committee
D15.07 - Specifications
Current Stage
Ref Project

Relations

Replaces
ASTM D3306-08 - Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service
Effective Date
15-May-2008
Replaced By
ASTM D3306-09 - Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service
Effective Date
01-Sep-2009
Referred By
ASTM D2570-16 - Standard Test Method for Simulated Service Corrosion Testing of Engine Coolants
Effective Date
15-May-2008
Referred By
ASTM D6210-17 - Standard Specification for Fully-Formulated Glycol Base Engine Coolant for Heavy-Duty Engines<rangeref></rangeref >
Effective Date
15-May-2008
Referred By
ASTM D4725-15(2023) - Standard Terminology for Engine Coolants and Related Fluids
Effective Date
15-May-2008
Referred By
ASTM D6660-01(2023) - Standard Test Method for Freezing Point of Aqueous Ethylene Glycol Base Engine Coolants by Automatic Phase Transition Method
Effective Date
15-May-2008
Referred By
ASTM D1119-22 - Standard Test Method for Percent Ash Content of Engine Coolants
Effective Date
15-May-2008
Referred By
ASTM D7715-12(2021) - Standard Specification for Fully-Formulated Glycerin Base Engine Coolant for Heavy-Duty Engines
Effective Date
15-May-2008
Referred By
ASTM D4985-10(2023) - Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA)
Effective Date
15-May-2008
Referred By
ASTM D2847-22 - Standard Practice for Testing Engine Coolants in Car and Light Truck Service
Effective Date
15-May-2008

Buy Standard

ASTM D3306-08a - Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty ServiceASTM D3306-08a - Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service
PreviousNext
Technical specification
ASTM D3306-08a - Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM D3306-08a - Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty ServiceREDLINE ASTM D3306-08a - Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service
PreviousNext
Technical specification
REDLINE ASTM D3306-08a - Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D3306 – 08a
Standard Specification for
Glycol Base Engine Coolant for Automobile and Light-Duty
1
Service
This standard is issued under the fixed designation D3306; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
TABLE 1 General Requirements
1. Scope
Property Specified Values ASTM Test Method
1.1 This specification covers the requirements for ethylene
Color Distinctive . . .
glycol or propylene glycol base engine coolants used in
Effect on nonmetals No adverse effect under consideration
automobiles or other light duty service cooling systems.When
concentratesareusedat40to70%concentrationbyvolumein
water, or when prediluted glycol base engine coolants (50 2. Referenced Documents
2
volume % minimum) are used without further dilution, they
2.1 ASTM Standards:
will function effectively to provide protection against freezing,
D512 Test Methods for Chloride Ion In Water
boiling, and corrosion.
D516 Test Method for Sulfate Ion in Water
1.2 The coolants governed by this specification are catego-
D1119 Test Method for Percent Ash Content of Engine
rized as follows:
Coolants
Coolant Type Description
D1120 Test Method for Boiling Point of Engine Coolants
D1121 Test Method for ReserveAlkalinity of Engine Cool-
I Ethylene glycol base concentrate
ants and Antirusts
II Propylene glycol base concentrate
III Ethylene glycol predilute (50 vol %)
D1122 Test Method for Density or Relative Density of
IV Propylene glycol predilute (50 vol %)
EngineCoolantConcentratesandEngineCoolantsByThe
Hydrometer
D1123 Test Methods for Water in Engine Coolant Concen-
NOTE 1—This specification is based on the knowledge of the perfor-
trate by the Karl Fischer Reagent Method
mance of engine coolants prepared from new or virgin ingredients. This
specification shall also apply to engine coolants prepared using glycol
D1126 Test Method for Hardness in Water
generated from recycled or reprocessed used coolant or reprocessed
D1177 Test Method for Freezing Point of Aqueous Engine
industrial-source glycol, provided that said glycol meets the requirements
Coolants
of Specification E1177. Separate specifications (D6471 and D6472) exist
D1287 Test Method for pH of Engine Coolants and Anti-
forenginecoolantspreparedfromrecycledorreprocessedusedcoolantor
rusts
reprocessed industrial-source glycol that does not meet the requirements
D1293 Test Methods for pH of Water
established in Specification E1177.
D1384 Test Method for CorrosionTest for Engine Coolants
1.3 The values stated in SI units are to be regarded as the
in Glassware
standard. The values in parentheses are for information only.
D1881 Test Method for Foaming Tendencies of Engine
1.4 This standard does not purport to address all of the
Coolants in Glassware
safety concerns, if any, associated with its use. It is the
D1882 TestMethodforEffectofCoolingSystemChemical
responsibility of the user of this standard to establish appro-
Solutions on Organic Finishes for Automotive Vehicles
priate safety and health practices and determine the applica-
D1888 Methods of Test for Particulate and Dissolved Mat-
bility of regulatory limitations prior to use.
3
ter in Water
NOTE 2—This specification applies to automobiles and light duty
D2570 Test Method for Simulated Service Corrosion Test-
service. Specifications D4985 and D6210 exist for heavy duty engine
ing of Engine Coolants
service.
1 2
ThisspecificationisunderthejurisdictionofASTMCommitteeD15onEngine For referenced ASTM standards, visit the ASTM website, www.astm.org, or
CoolantsandisthedirectresponsibilityofSubcommitteeD15.07onSpecifications. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Current edition approved May 15, 2008. Published June 2008. Originally Standards volume information, refer to the standard’s Document Summary page on
approved in 1974. Last previous edition approved in 2008 as D3306–08. DOI: the ASTM website.
3
10.1520/D3306-08A. Withdrawn.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D3306 – 08a
TABLE 2 Physical and Chemical Requirements
Property Type I Type II Type III Type IV ASTM Test Method
Relative density 1.110 to 1.145 1.030 to 1.065 1.065 min 1.025 min D1122, D5931
15.5/15.5°C (60/60°F)
Freezing point, °C (°F): D1177,
D6660D1177D6660
50 vol % in DI water −37 (−34) max −31 (−24) max
Undiluted −37 (−34) max −31 (−24) max
A
Boiling point, °C (°F): D1120
50 vol % in DI water 108 (226) min 104 (219) min
Undiluted 163 (325) min 152 (305 min) 108 (226) min 104 (219) min
As
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately,ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D3306–08 Designation: D 3306 – 08a
Standard Specification for
Glycol Base Engine Coolant for Automobile and Light-Duty
1
Service
This standard is issued under the fixed designation D3306; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 Thisspecificationcoverstherequirementsforethyleneglycolorpropyleneglycolbaseenginecoolantsusedinautomobiles
or other light duty service cooling systems.When concentrates are used at 40 to 70% concentration by volume in water, or when
prediluted glycol base engine coolants (50 volume % minimum) are used without further dilution, they will function effectively
to provide protection against freezing, boiling, and corrosion.
1.2 The coolants governed by this specification are categorized as follows:
Coolant Type Description
I Ethylene glycol base concentrate
II Propylene glycol base concentrate
III Ethylene glycol predilute (50 vol %)
IV Propylene glycol predilute (50 vol %)
NOTE 1—This specification is based on the knowledge of the performance of engine coolants prepared from new or virgin ingredients. This
specification shall also apply to engine coolants prepared using glycol generated from recycled or reprocessed used coolant or reprocessed
industrial-source glycol, provided that said glycol meets the requirements of Specification E1177. Separate specifications (D6471 and D6472) exist for
engine coolants prepared from recycled or reprocessed used coolant or reprocessed industrial-source glycol that does not meet the requirements
established in Specification E1177.
1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
NOTE 2—This specification applies to automobiles and light duty service. Specifications D4985 and D6210 exist for heavy duty engine service.
2. Referenced Documents
2
2.1 ASTM Standards:
D512 Test Methods for Chloride Ion In Water
D516 Test Method for Sulfate Ion in Water
D1119 Test Method for Percent Ash Content of Engine Coolants
D1120 Test Method for Boiling Point of Engine Coolants
D1121 Test Method for Reserve Alkalinity of Engine Coolants and Antirusts
D1122 TestMethodforDensityorRelativeDensityofEngineCoolantConcentratesandEngineCoolantsByTheHydrometer
D1123 Test Methods for Water in Engine Coolant Concentrate by the Karl Fischer Reagent Method
D1126 Test Method for Hardness in Water
D1177 Test Method for Freezing Point of Aqueous Engine Coolants
D1287 Test Method for pH of Engine Coolants and Antirusts
D1293 Test Methods for pH of Water
D1384 Test Method for Corrosion Test for Engine Coolants in Glassware
D1881 Test Method for Foaming Tendencies of Engine Coolants in Glassware
D1882 Test Method for Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles
1
This specification is under the jurisdiction of ASTM Committee D15 on Engine Coolants and is the direct responsibility of Subcommittee D15.07 on Specifications .
Current edition approved Jan.May 15, 2008. Published FebruaryJune 2008. Originally approved in 1974. Last previous edition approved in 20052008 as D3306–058.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book ofASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D 3306 – 08a
TABLE 1 General Requirements
Property Specified Values ASTM Test Method
Color Distinctive . . .
Effect on nonmetals No adverse effect under consideration
TABLE 2 Physical and Chemical Requirements
Property Type I Type II Type III Type IV ASTM Test Method
Relative density 1.110 to 1.145 1.030 to 1.065 1.065 min 1.025 min D 1122, D 5931
15.5/15.5°C (60/60°F)
Freezing point, °C (°F): D 1177, D 6660
50 vol % in DI water −37 (−34) max −32 (−26) max
Undiluted −37 (−34) max −32 (−26) max
A
Boiling point, °C (°F): D 1120
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D7713-18(2023)(Specification)
Standard Specification for Aqueous Engine Coolant Grade Glycol (53 % by Volume Nominal)

ABSTRACT
This specification covers both commercial products, engine coolant grade ethylene glycol and propylene glycol, including virgin glycols and those derived from the recycling of vehicle engine coolants and industrial source glycols. Types EG-1 and PG-1, which will probably be virgin materials, cover glycols with sufficiently low limits on components to allow a blended coolant to meet most Original Equipment Manufacturer (OEM) specifications. Types EG-2 and PG-2, on the other hand, can be either redistilled or virgin. These cover glycol that will be suitable for many coolants.
SCOPE
1.1 This specification covers both commercial products, engine coolant grade ethylene glycol and propylene glycol, including virgin glycols and those derived from the recycling of vehicle engine coolants and industrial source glycols.  
1.2 Types EG-1 and PG-1 cover glycols with sufficiently low limits on components to allow a blended coolant to meet most OEM (Original Equipment Manufacturer) specifications. These types will probably be virgin materials, although redistillation could produce a sufficiently pure product. Types EG-2 and PG-2 cover glycol that will be suitable for many coolants. These types can be either redistilled or virgin.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D7437-23(Test Method)
Standard Test Method for Temperature and Hard Water Stability of Engine Coolants

SIGNIFICANCE AND USE
4.1 This test method provides information on the stability of the engine coolant concentrate when stored at elevated temperatures for two weeks. These test conditions might simulate the conditions that a product would be subjected to in transit and storage in warehouses before delivery to the customer.  
4.2 This test method provides information on the stability of an engine coolant diluted with synthetic hard water at elevated temperatures. This test method provides a laboratory method to test the sensitivity of the engine coolant to hard water.
SCOPE
1.1 This test method covers a simple glassware-type procedure for evaluating the effects of temperature and hard water on the stability of engine coolants at elevated temperatures under controlled laboratory conditions.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4725-15(2023)(Terminology)
Standard Terminology for Engine Coolants and Related Fluids

SCOPE
1.1 This document covers terminology relating to engine coolants. It is intended to provide a reference for anyone seeking information on engine coolants, and also to provide a uniform set of definitions for use in preparing ASTM specifications, test methods and other standard documents.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4985-10(2023)(Specification)
Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA)

ABSTRACT
This specification covers the requirements for low silicate ethylene glycol base engine coolants for cooling systems of heavy-duty engines. Such engines are typically used in off-highway machinery for agriculture, mining, earth-moving, and construction; Class 5 to 8 over the road trucks and buses; high output stationary engine installations; and locomotive and marine installations. Prediluted coolants shall be prepared using deionized Ethylene glycol base engine coolant concentrates or prediluted ethylene glycol base engine coolants shall be formulated with ethylene glycol. The coolants shall conform to the prescribed physical, chemical, and performance requirements, which include relative density, freezing point, boiling point, ash content, pH, reserve alkalinity, water content, chloride ion content, silicon content, corrosion in glassware, simulated service test, foaming, and cavitation. The color and effect of nonmetals of the coolant shall be evaluated. Prediluted coolant shall also meet the required content of sulfate and iron. Its CaCO3 content shall be tested to determine its hardness.
SCOPE
1.1 This specification covers the requirements for low silicate ethylene glycol base engine coolants for cooling systems of heavy-duty engines. When concentrates are used at 40 % to 60 % concentration by volume in water, or when prediluted glycol base engine coolants (50 volume % minimum) are used without further dilution, they will function effectively to provide protection against corrosion, freezing to at least −36.4 °C (−33.5 °F), and boiling to at least 108 °C (226 °F).
Note 1: This specification is based on the knowledge of the performance of engine coolants prepared from new or virgin ingredients. A separate specification exists (Specification D6210) for heavy-duty engine coolants which may be prepared from recycled or reprocessed used coolant or reprocessed industrial-source ethylene glycol.  
1.2 Coolants meeting this specification require an initial charge of a supplemental coolant additive (SCA) and require regular maintenance doses of an SCA to continue the protection in certain operating heavy-duty engine cooling systems, particularly those of the wet cylinder liner-in-block design. The SCA additions are defined by and are the primary responsibility of the engine manufacturer or vehicle manufacturer. If they provide no instructions, follow the SCA supplier's recommended instructions.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM D6660-01(2023)(Test Method)
Standard Test Method for Freezing Point of Aqueous Ethylene Glycol Base Engine Coolants by Automatic Phase Transition Method

SIGNIFICANCE AND USE
5.1 The freezing point of an engine coolant indicates the coolant freeze protection.  
5.2 The freezing point of an engine coolant may be used to determine the approximate glycol content, provided the glycol type is known.  
5.3 Freezing point as measured by Test Method D1177 or approved alternative method is a requirement in Specifications D3306 and D6210.  
5.4 This test method provides results that are equivalent to Test Method D1177 and expresses results to the nearest 0.1 °C with improved reproducibility over Test Method D1177.  
5.5 This test method determines the freezing point in a shorter period of time than Test Method D1177.  
5.6 This test method removes most of the operator time and judgement required by Test Method D1177.
SCOPE
1.1 This test method covers the determination of the freezing point of an aqueous engine coolant solution.  
1.2 This test method is designed to cover ethylene glycol base coolants up to a maximum concentration of 60 % (v/v) in water; however, the ASTM interlaboratory study mentioned in 12.2 has only demonstrated the test method with samples having a concentration range of 40 % to 60 % (v/v) water.
Note 1: Where solutions of specific concentrations are to be tested, they shall be prepared from representative samples as directed in Practice D1176. Secondary phases separating on dilution need not be separated.
Note 2: The products may also be marketed in a ready-to-use form (prediluted).  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in 7.3.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D5828-97(2023)(Test Method)
Standard Test Method for Compatibility of Supplemental Coolant Additives (SCAs) and Engine Coolant Concentrates

SIGNIFICANCE AND USE
5.1 This test was developed to mimic the formation of insolubles observed in some heavy-duty diesel cooling systems during the mid 1980s. It measures the compatibility of SCA and coolant concentrate solutions according to their tendency to form insolubles in service.3 Such insoluble materials may accumulate within a cooling system, restrict heat transfer through radiator cores, and contribute to the damage of components such as water pumps.
SCOPE
1.1 This test method covers determination of the compatibility of commercial SCA and commercial ethylene and propylene glycol engine coolant concentrates. This test method focuses on the solubility of specific chemical species formed in the engine coolant. The short duration of the test (24 h), among other restrictions, makes the test method of limited use for sorting out a variety of chemical compatibility problems in which a component of the SCA may react with a component of the coolant additive package. The test as currently written also does not deal with the issue of hard water compatibility, in which a component of the coolant or SCA additive package reacts with the hardness (Ca and Mg) to form a precipitate.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D8039-16(2023)(Specification)
Standard Specification for Heat Transfer Fluids (HTF) for Heating and Air Conditioning (HVAC) Systems

ABSTRACT
This specification establishes the requirements for ethylene glycol, propylene glycol, 1,3 propanediol, and glycerin base heat transfer fluids (HTF) used in heating and air conditioning (HVAC) systems. When concentrates are used at up to 65% concentration by weight in water, or when prediluted heat transfer fluids (30% by weight minimum) are used without further dilution, they will function effectively to provide protection against freezing, and corrosion. The HTFs governed by this specification are categorized according to the primary base of freeze depressant used: I (ethylene glycol), II (propylene glycol), III (1,3-propanediol), and IV (glycerin).
SCOPE
1.1 This specification covers the requirements for ethylene glycol, propylene glycol, 1,3 propanediol as well as glycerin base heat transfer fluids (HTF) used in heating and air conditioning (HVAC) systems. When concentrates are used at up to 65 % concentration by weight in water, or when prediluted heat transfer fluids (30 % by weight minimum) are used without further dilution, they will function effectively to provide protection against freezing, and corrosion.  
1.2 The fluids described in this specification are not appropriate for use in systems where internal combustion engines (gasoline, diesel, or CNG/LPG) are used.  
1.3 The heat transfer fluids governed by this specification are categorized as follows by the primary base of freeze depressant used:    
Heat Transfer
Fluid Type  
Description  
I  
Ethylene glycol  
II  
Propylene glycol  
III  
1,3-Propanediol  
IV  
Glycerin  
1.4 Heat transfer fluids meeting this specification shall be tested and fully comply with requirements listed in Table 1.  
Note 1: This specification is based on the knowledge of the performance of heat transfer fluids prepared from new or virgin ingredients. This specification shall also apply to heat transfer fluids prepared using materials generated from recycled or reprocessed ingredients, provided that these ingredients meet the requirements of Specifications E1177 and D7388 for Glycols and Specification D7640 for Glycerin.
Note 2: This specification addresses concentrated inhibited glycols and glycerol that will be mixed with water for use in various climates and prediluted heat transfer fluids (HTF) that are factory-blended with purified water. A table of estimated freeze protection temperatures at appropriate dilutions is provided in Appendix X1.  
1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D8485-23(Test Method)
Standard Test Method for Corrosion Test for Electric Vehicle Coolants in Glassware

SIGNIFICANCE AND USE
5.1 This test method provides a method to distinguish between coolants that are deleterious from the corrosion standpoint and those suitable for further evaluation.
FIG. 1 Metal Specimens and Equipment for the 336 h Corrosion Test
FIG. 2 Tall Form Beaker Specimens and Equipment for the 336 h Corrosion Test
SCOPE
1.1 This test method covers a simple beaker-type procedure for evaluating the effects of glycol-based electric vehicle coolants on metal specimens under controlled laboratory conditions.  
1.2 This test method evaluates the corrosion on test specimens of stainless steel and aluminum, with an option for a copper test specimen.  
1.3 This test method evaluates coolants without the addition of any corrosive elements.  
1.4 Additional types of metal test specimens may be evaluated.  
1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM E1177-23(Specification)
Standard Specification for Engine Coolant Grade Glycol

ABSTRACT
This specification establishes the testing and requirements of four types of engine coolant grade ethylene glycol and propylene glycol, including virgin glycols and those derived from the recycling of vehicle engine coolants and industrial source glycols. Types EG-1 and PG-1 cover glycols with sufficiently low limits on components to allow a blended coolant to meet most OEM (Original Equipment Manufacturer) specifications. These types will probably be virgin materials, although redistillation could produce a sufficiently pure product. Types EG-2 and PG-2 cover glycol that will be suitable for many coolants, and can either be redistilled or virgin. The commercial products shall be suitably sampled and tested, and shall conform accordingly to specified values of the following physical and chemical properties: clarity; color (Pt/Co scale); relative density; pH by volume in distilled water; acidity as acetic acid; composition by mass of individual glycols (including ethylene glycol, propylene glycol, dipropylene glycol, and others); total composition by mass of all glycols; water content; glycol ester content; and the maximum content for nitrites, nitrates, phosphates, silicon, chloride, sulfate, boron, aluminum, calcium, copper, iron, magnesium, lead, zinc, and iron.
SCOPE
1.1 This specification covers commercial products, engine coolant grade ethylene glycol and propylene glycol, including virgin glycols and those derived from the recycling of vehicle engine coolants and industrial source glycols.  
1.2 Types EG-1 and PG-1 cover glycols with sufficiently low limits on components to allow a blended coolant to meet most OEM (Original Equipment Manufacturer) specifications. These types will probably be virgin materials, although redistillation could produce a sufficiently pure product. Types EG-2 and PG-2 cover glycol that will be suitable for many coolants. These types can be either redistilled or virgin.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D1177-22(Test Method)
Standard Test Method for Freezing Point of Aqueous Engine Coolants

SIGNIFICANCE AND USE
5.1 The freezing point of an engine coolant indicates the coolant freeze protection.  
5.2 The freezing point of an engine coolant may be used to determine the approximate glycol or glycerin content, provided the glycol type is known.
SCOPE
1.1 This test method covers the determination of the freezing point of an aqueous engine coolant solution in the laboratory.  
Note 1: Where solutions of specific concentrations are to be tested, they shall be prepared from representative samples as directed in Practice D1176. Secondary phases separating on dilution need not be separated.
Note 2: These products may also be marketed in a ready-to-use form (prediluted).  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off