ASTM B366-10
(Specification)Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings
Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings
ABSTRACT
This specification covers wrought welding fittings, including threaded fittings, for pressure piping, factory-made from nickel and nickel alloys. The term welding applies to butt-welding or socket-welding parts such as elbows, bends, caps, tees, reducers, lap-joint, and stub ends. This specification does not apply to cast welding fittings. Grades of nickel and nickel alloys included in this specification are designated with a prefix, WP or CR, based on dimensional and rating standards. WP grades have class designations (Class S, Class W, Class WX, and Class WU) to indicate whether seamless or welded construction is utilized and to indicate the nondestructive test method and extent of nondestructive examination (such as radiography and/or ultrasonic test). The material for wrought welding fittings may consist of forgings, rods, bars, plates, sheets, and seamless or welded pipe that conform to all the specified requirements. Forging or shaping operations may be performed by hammering, pressing, piercing, extruding, upsetting, rolling, bending, or fusion welding, or by a combination of two or more of these operations. Chemical and product analyses shall conform to the chemical composition prescribed. Requirements for tensile properties, heat treatment, tension test, and dimensions are detailed. Hydrostatic testing of wrought fittings is not required by this specification.
SCOPE
1.1 This specification covers wrought welding fittings for pressure piping, factory-made from nickel and nickel alloys. Threaded fittings as covered in ASME B16.11 are also covered by this specification. The term welding applies to butt-welding or socket-welding parts such as 45 and 90° elbows, 180° bends, caps, tees, reducers, lap-joint stub ends, and other types, as covered by ASME B16.9, ASME B16.11, MSS SP-43, MSS SP-95, and MSS SP-97.
1.1.1 Several grades of nickel and nickel alloys are included in this specification. Grades are designated with a prefix, WP or CR, based on the applicable ASME or MSS dimensional and rating standards.
1.1.2 Class WP fittings are those manufactured to the requirements of ASME B16.9, B16.11.
1.1.3 For each of the WP nickel and nickel alloy grades, several classes of fittings are covered to indicate whether seamless or welded construction was utilized. Class designations are also utilized to indicate the nondestructive test method and extent of nondestructive examination (NDE). Table 1 is general summary of the fitting classes applicable to all WP grades of nickel and nickel alloys covered by this specification. There are no classes for the CR grades. Specific requirements are covered elsewhere.
1.2 This specification does not apply to cast welding fittings.
1.3 Optional supplementary requirements are provided for fittings where a greater degree of examination is desired. These supplementary requirements call for additional tests. When desired, one or more of these may be specified in the order.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B366 – 10
Standard Specification for
1
Factory-Made Wrought Nickel and Nickel Alloy Fittings
This standard is issued under the fixed designation B366; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* supplementary requirements call for additional tests. When
desired, one or more of these may be specified in the order.
1.1 This specification covers wrought welding fittings for
1.4 The values stated in inch-pound units are to be regarded
pressure piping, factory-made from nickel and nickel alloys.
as standard. The values given in parentheses are mathematical
Threaded fittings as covered inASME B16.11 are also covered
conversions to SI units that are provided for information only
by this specification. The term welding applies to butt-welding
and are not considered standard.
orsocket-weldingpartssuchas45and90°elbows,180°bends,
1.5 This standard does not purport to address all of the
caps, tees, reducers, lap-joint stub ends, and other types, as
safety concerns, if any, associated with its use. It is the
covered by ASME B16.9, ASME B16.11, MSS SP-43, MSS
responsibility of the user of this standard to become familiar
SP-95, and MSS SP-97.
with all hazards including those identified in the appropriate
1.1.1 Severalgradesofnickelandnickelalloysareincluded
Material Safety Data Sheet (MSDS) for this product/material
inthisspecification.Gradesaredesignatedwithaprefix,WPor
as provided by the manufacturer, to establish appropriate
CR, based on the applicable ASME or MSS dimensional and
safety and health practices, and determine the applicability of
rating standards.
regulatory limitations prior to use.
1.1.2 Class WP fittings are those manufactured to the
requirements of ASME B16.9, B16.11.
2. Referenced Documents
1.1.3 For each of the WP nickel and nickel alloy grades,
2
2.1 ASTM Standards:
several classes of fittings are covered to indicate whether
B127 Specification for Nickel-Copper Alloy (UNS
seamless or welded construction was utilized. Class designa-
N04400) Plate, Sheet, and Strip
tionsarealsoutilizedtoindicatethenondestructivetestmethod
B160 Specification for Nickel Rod and Bar
and extent of nondestructive examination (NDE). Table 1 is
B161 Specification for Nickel Seamless Pipe and Tube
general summary of the fitting classes applicable to all WP
B162 Specification for Nickel Plate, Sheet, and Strip
gradesofnickelandnickelalloyscoveredbythisspecification.
B163 Specification for Seamless Nickel and Nickel Alloy
There are no classes for the CR grades. Specific requirements
Condenser and Heat-Exchanger Tubes
are covered elsewhere.
B164 Specification for Nickel-Copper Alloy Rod, Bar, and
Wire
TABLE 1 Fitting Classes for WP Grades
B165 Specification for Nickel-Copper Alloy (UNS
N04400)* Seamless Pipe and Tube
Class Construction Nondestructive Examination
B166 Specification for Nickel-Chromium-Iron Alloys
S Seamless None
W Welded Radiography or Ultrasonic (UNS N06600, N06601, N06603, N06690, N06693,
WX Welded Radiography
N06025, N06045, and N06696)* and Nickel-Chromium-
WU Welded Ultrasonic
Cobalt-Molybdenum Alloy (UNS N06617) Rod, Bar, and
Wire
B167 Specification for Nickel-Chromium-Iron Alloys
1.2 This specification does not apply to cast welding fit-
(UNS N06600, N06601, N06603, N06690, N06693,
tings.
N06025, N06045, and N06696)* and Nickel-Chromium-
1.3 Optional supplementary requirements are provided for
Cobalt-Molybdenum Alloy (UNS N06617) Seamless Pipe
fittingswhereagreaterdegreeofexaminationisdesired.These
and Tube
B168 Specification for Nickel-Chromium-Iron Alloys
(UNS N06600, N06601, N06603, N06690, N06693,
1
This specification is under the jurisdiction of ASTM Committee B02 on
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
2
B02.07 on Refined Nickel and Cobalt and Their Alloys. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved April 1, 2010. Published May 2010. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
´1
approved in 1961. Last previous edition approved in 2004 as B366 – 04b . DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/B0366-10. the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B366 – 10
N06025, N06045, and N06696) and Nickel-Chromium- B515 Specification for Welded UNS N08120, UNS
Cobalt-Molybdenum Alloy (UNS N06617) Plate, Shee
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation:B366–04b Designation: B366 – 10
Standard Specification for
1
Factory-Made Wrought Nickel and Nickel Alloy Fittings
This standard is issued under the fixed designation B366; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
´ NOTE—Editorial changes were made in Table3 in November 2006.
1. Scope*
1.1 Thisspecificationcoverswroughtweldingfittingsforpressurepiping,factory-madefromnickelandnickelalloys.Threaded
fittings as covered in ASME B16.11 are also covered by this specification. The term welding applies to butt-welding or
socket-welding parts such as 45 and 90° elbows, 180° bends, caps, tees, reducers, lap-joint stub ends, and other types, as covered
by ASME B16.9, ASME B16.11, MSS SP-43, MSS SP-95, and MSS SP-97.
1.1.1 Several grades of nickel and nickel alloys are included in this specification. Grades are designated with a prefix, WP or
CR, based on the applicable ASME or MSS dimensional and rating standards.
1.1.2 Class WP fittings are those manufactured to the requirements of ASME B16.9, B16.11.
1.1.3 For each of the WP nickel and nickel alloy grades, several classes of fittings are covered to indicate whether seamless or
welded construction was utilized. Class designations are also utilized to indicate the nondestructive test method and extent of
nondestructive examination (NDE). Table 1 is general summary of the fitting classes applicable to all WP grades of nickel and
nickel alloys covered by this specification. There are no classes for the CR grades. Specific requirements are covered elsewhere.
1.2 This specification does not apply to cast welding fittings.
TABLE 1 Fitting Classes for WP Grades
Class Construction Nondestructive Examination
S Seamless None
W Welded Radiography or Ultrasonic
WX Welded Radiography
WU Welded Ultrasonic
1.3 Optional supplementary requirements are provided for fittings where a greater degree of examination is desired. These
supplementary requirements call for additional tests. When desired, one or more of these may be specified in the order.
1.4The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
B127 Specification for Nickel-Copper Alloy (UNS N04400) Plate, Sheet, and Strip
B160 Specification for Nickel Rod and Bar
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB02onNonferrousMetalsandAlloysandisthedirectresponsibilityofSubcommitteeB02.07onRefined
Nickel and Cobalt and Their Alloys.
Current edition approved Oct. 1, 2004. Published October 2004. Originally approved in 1961. Last previous edition approved in 2004 as B366–04a. DOI:
10.1520/B0366-04BE01.
´1
Current edition approved April 1, 2010. Published May 2010. Originally approved in 1961. Last previous edition approved in 2004 as B366 – 04b . DOI:
10.1520/B0366-10.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B366 – 10
B161 Specification for Nickel Seamless Pipe and Tube
B162 Specification for Nickel Plate, Sheet, and Strip
B163 Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes
B164 Specification for Nickel-Copper Alloy Rod, Bar, and Wire
B165 Specification for Nickel-Copper Allo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.