ASTM C1884-23
(Specification)Standard Specification for Manufactured Concrete Ballast Units
Standard Specification for Manufactured Concrete Ballast Units
SCOPE
1.1 This specification covers dry-cast, manufactured concrete units that are primarily used for ballast applications. These units are machine-made from hydraulic cement, water, and suitable mineral aggregates with or without the inclusion of other materials.
Note 1: The design of concrete ballast units systems for resisting wind uplift is beyond the scope of this specification. Building codes and other standards should be consulted in designing for wind uplift resistance.
Note 2: Previously, there were two standards that covered units used for ballast. Specification C1491 was for concrete roof pavers, primarily used for roof ballast and protection of roof membrane. Specification C1884 was for units for ballast for rooftop equipment. Due to the similarity in these units and application, this standard now serves as the single standard for manufactured concrete units used in all ballast applications.
1.2 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: C1884 − 23
Standard Specification for
1
Manufactured Concrete Ballast Units
This standard is issued under the fixed designation C1884; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2.1 ASTM Standards:
1.1 This specification covers dry-cast, manufactured con-
C33/C33M Specification for Concrete Aggregates
crete units that are primarily used for ballast applications.
C140/C140M Test Methods for Sampling and Testing Con-
These units are machine-made from hydraulic cement, water,
crete Masonry Units and Related Units
and suitable mineral aggregates with or without the inclusion
C150/C150M Specification for Portland Cement
of other materials.
C331/C331M Specification for Lightweight Aggregates for
NOTE 1—The design of concrete ballast units systems for resisting wind Concrete Masonry Units
uplift is beyond the scope of this specification. Building codes and other
C595/C595M Specification for Blended Hydraulic Cements
standards should be consulted in designing for wind uplift resistance.
C618 Specification for Coal Ash and Raw or Calcined
NOTE 2—Previously, there were two standards that covered units used
Natural Pozzolan for Use in Concrete
for ballast. Specification C1491 was for concrete roof pavers, primarily
C979/C979M Specification for Pigments for Integrally Col-
used for roof ballast and protection of roof membrane. Specification
ored Concrete
C1884 was for units for ballast for rooftop equipment. Due to the
C989/C989M Specification for Slag Cement for Use in
similarity in these units and application, this standard now serves as the
single standard for manufactured concrete units used in all ballast
Concrete and Mortars
applications.
C1157/C1157M Performance Specification for Hydraulic
Cement
1.2 The text of this standard references notes and footnotes
C1232 Terminology for Masonry
that provide explanatory material. These notes and footnotes
C1240 Specification for Silica Fume Used in Cementitious
(excluding those in tables and figures) shall not be considered
Mixtures
as requirements of the standard.
C1262/C1262M Test Method for Evaluating the Freeze-
1.3 The values stated in inch-pound units are to be regarded
Thaw Durability of Dry-Cast Segmental Retaining Wall
as standard. The values given in parentheses are mathematical
Units and Related Concrete Units
conversions to SI units that are provided for information only
C1491 Specification for Concrete Roof Pavers
and are not considered standard.
3. Terminology
1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the 3.1 Terminology defined in Terminology C1232 shall apply
to this specification.
responsibility of the user of this standard to establish appro-
priate safety, health, and environmental practices and deter-
3.2 Definitions of Terms Specific to This Standard:
mine the applicability of regulatory limitations prior to use.
3.2.1 concrete ballast unit, n—a manufactured concrete unit
1.5 This international standard was developed in accor-
used primarily to provide weight for stabilizing materials.
dance with internationally recognized principles on standard- 3.2.1.1 Discussion—Example applications for concrete bal-
ization established in the Decision on Principles for the
last units are ballast for photovoltaic arrays, or paving to
Development of International Standards, Guides and Recom- protect roofing membranes.
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee. 4. Material
4.1 Cementitious Materials—Materials shall conform to the
following applicable specifications:
1
4.1.1 Portland Cement—Specification C150/C150M.
This specification is under the jurisdiction of ASTM Committee C15 on
Manufactured Masonry Units and is the direct responsibility of Subcommittee
4.1.2 Modified Portland Cement—Portland cement con-
C15.03 on Concrete Masonry Units and Related Units.
forming to Specification C150/C150M, modified as follows:
Current edition approved June 1, 2023. Published June 2023. Originally
4.1.2.1 Limestone—Limestone, with a minimum 85 % cal-
approved in 2018. Last previous edition approved in 2022 as C1884–22. DOI:
10.1520/C1884-23 cium carbonate (CaCO ) content, shall be permitted to be
3
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1884 − 22 C1884 − 23
Standard Specification for
1
Manufactured Concrete Ballast BlockUnits
This standard is issued under the fixed designation C1884; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers dry-cast concrete ballast blocks dry-cast, manufactured concrete units that are primarily used for
ballast of rooftop equipment. applications. These units are machine-made from hydraulic cement, water, and suitable mineral
aggregates with or without the inclusion of other materials.
NOTE 1—The design of concrete ballast blockunits systems for resisting wind uplift is beyond the scope of this specification. Building codes and other
standards should be consulted in designing for wind uplift resistance.
NOTE 2—Previously, there were two standards that covered units used for ballast. Specification C1491 was for concrete roof pavers, primarily used for
roof ballast and protection of roof membrane. Specification C1884 was for units for ballast for rooftop equipment. Due to the similarity in these units
and application, this standard now serves as the single standard for manufactured concrete units used in all ballast applications.
1.2 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the standard.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 ASTM Standards:
C33/C33M Specification for Concrete Aggregates
C140/C140M Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
C150/C150M Specification for Portland Cement
C331/C331M Specification for Lightweight Aggregates for Concrete Masonry Units
C595/C595M Specification for Blended Hydraulic Cements
C618 Specification for Coal Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C979/C979M Specification for Pigments for Integrally Colored Concrete
1
This specification is under the jurisdiction of ASTM Committee C15 on Manufactured Masonry Units and is the direct responsibility of Subcommittee C15.03 on
Concrete Masonry Units and Related Units.
Current edition approved Dec. 1, 2022June 1, 2023. Published December 2022June 2023. Originally approved in 2018. Last previous edition approved in 20192022 as
C1884–19. DOI: 10.1520/C1884-22–22. DOI: 10.1520/C1884-23
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1884 − 23
C989/C989M Specification for Slag Cement for Use in Concrete and Mortars
C1157/C1157M Performance Specification for Hydraulic Cement
C1232 Terminology for Masonry
C1240 Specification for Silica Fume Used in Cementitious Mixtures
C1262/C1262M Test Method for Evaluating the Freeze-Thaw Durability of Dry-Cast Segmental Retaining Wall Units and
Related Concrete Units
C1491 Specification for Concrete Roof Pavers
3. Terminology
3.1 Terminology defined in Terminology C1232 shall apply to this specification.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 concrete ballast block,unit, n—a manufactured concrete unit used primarily to provide weight for stabilizing rooftop
equipment.materials.
3.2.1.1 Discussion—
An example application Example applications for concrete ballast block isunits are ballast for photovoltaic arrays.arrays, or paving
to protect roofing membrane
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.