ASTM F1199-88(2015)
(Specification)Standard Specification for Cast (All Temperatures and Pressures) and Welded Pipe Line Strainers (150 psig and 150°F Maximum)
Standard Specification for Cast (All Temperatures and Pressures) and Welded Pipe Line Strainers (150 psig and 150°F Maximum)
ABSTRACT
This specification provides the minimum requirements for the design, fabrication, rating, marking, and testing of all cast pipe line strainers, and welded pipe line strainers used in services up to 150 psig and 150°F (1 MPa and 65°C) that are acceptable for use in marine environments. The strainers may be classified into three general construction categories, namely, simplex, duplex (or multiplex), and automatic (self-cleaning). They may also be further classified according to pressure ratings and types of port connections, port alignments relative to unit center lines, cover closures, valve types (in duplex), types of baskets or elements, materials of construction, and other features of design.
SCOPE
1.1 This specification covers all cast strainers and welded strainers in services up to 150 psig and 150°F (1 MPa and 65°C). For welded strainers used in services above 150 psig and 150°F, see Specification F1200.
1.2 This standard provides the minimum requirements for the design, fabrication, rating, marking, and testing of cast and welded pipe line strainers for services above 0°F (−18°C).
1.3 Strainers manufactured to this specification are acceptable for use in the marine environment.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1199 −88 (Reapproved 2015) An American National Standard
Standard Specification for
Cast (All Temperatures and Pressures) and Welded Pipe
Line Strainers (150 psig and 150°F Maximum)
This standard is issued under the fixed designation F1199; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope B16.4Cast Iron Threaded Fittings
B16.5Steel Pipe Flanges and Flanged Fittings
1.1 This specification covers all cast strainers and welded
B16.11 ForgedSteelFittings,Socket-WeldingandThreaded
strainers in services up to 150 psig and 150°F (1 MPa and
B16.15Cast Bronze Threaded Fittings
65°C). For welded strainers used in services above 150 psig
B16.24Bronze Pipe Flanges and Flanged Fittings
and 150°F, see Specification F1200.
B16.25Buttwelding Ends
1.2 This standard provides the minimum requirements for
B31.1Power Piping
the design, fabrication, rating, marking, and testing of cast and
2.3 MSS Standards:
welded pipe line strainers for services above 0°F (−18°C).
SP-51150 lb Corrosion Resistant Cast Flanges and Flanged
1.3 Strainers manufactured to this specification are accept-
Fittings
able for use in the marine environment.
SP-63High Strength Wrought Welding Fittings
1.4 The values stated in inch-pound units are to be regarded
2.4 ASME Standards:
as standard. The values given in parentheses are mathematical
ASME Boiler and Pressure Vessel CodeSection VIII, Divi-
conversions to SI units that are provided for information only
sion 1, Pressure Vessels
and are not considered standard.
3. Terminology
1.5 The following safety hazards caveat pertains only to the
test methods portion, Section 8, of this specification. This
3.1 Definitions:
standard does not purport to address all of the safety concerns,
3.1.1 basket or element—the replaceable part in a strainer
if any, associated with its use. It is the responsibility of the user
that performs the barrier separation of solid particles from
of this standard to establish appropriate safety and health
flowing fluid. It is normally removable for cleaning and
practices and determine the applicability of regulatory limita-
servicing and can be furnished in a wide variety of materials,
tions prior to use.
particle size removal capability, straining area, and types of
construction.Interchangeablebasketsorelementsarenormally
2. Referenced Documents
available for a given make, model, and size strainer.
2.1 ASTM Standards:
3.1.2 maximum allowable working pressure (MAWP)—the
F1200 Specification for Fabricated (Welded) Pipe Line
highest internal pressure that the strainer can be subjected to in
Strainers (Above 150 psig and 150°F)
service.Themaximumnonshockworkingpressureforwhicha
2.2 ANSI Standards:
strainer is rated by the manufacturer.
B2.1Pipe Threads
3.1.3 maximum design temperature—the maximum tem-
B16.1Cast Iron Pipe Flanges and Flanged Fittings
perature for which a strainer is rated by the manufacturer.
B16.3Malleable Iron Threaded Fittings
3.1.4 strainer—a device which, when installed in a pipe
line, provides a mechanical means of removing solids from a
This specification is under the jurisdiction of ASTM Committee F25 on Ships
flowing liquid or gas by using a barrier element.
and Marine Technology and is the direct responsibility of Subcommittee F25.11 on
3.1.5 straining open area—theneteffectiveopenareaofthe
Machinery and Piping Systems.
Current edition approved May 1, 2015. Published June 2015. Originally
clean element through which the fluid can pass.
approved in 1988. Last previous edition approved in 2010 as F1199–88 (2010).
DOI: 10.1520/F1199-88R15.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM AvailablefromManufacturersStandardizationSocietyoftheValveandFittings
Standards volume information, refer to the standard’s Document Summary page on Industry(MSS),127ParkSt.,NE,Vienna,VA22180-4602,http://www.mss-hq.org.
the ASTM website. Available from American Society of Mechanical Engineers (ASME), ASME
Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St., International Headquarters, Two Park Ave., New York, NY 10016-5990, http://
4th Floor, New York, NY 10036, http://www.ansi.org. www.asme.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F1199−88 (2015)
4. Classification 5.3 In general, the standard product description should not
be mixed with the performance criteria because conflicting
4.1 Strainers may be classified into three general construc-
specifications can result (for example, maximum allowable
tion categories, simplex, duplex (or multiplex), and automatic
pressure loss inconsistent with product size).
(self-cleaning), as follows:
4.1.1 Simplex—A strainer consisting of a single basket or
6. Materials and Manufacture
element chamber that normally requires the flow through the
unit to be shut down before cleaning.
6.1 Strainer housings, as well as any pressure-retaining
4.1.1.1 Classifications of simplex strainers based on port
parts, including bolting used for pressure retention, shall be
alignmentrelativetobasketorelementchamberare Y, T, Z,and
constructedofmaterialslistedinSectionVIII,Division1ofthe
others. ASME Boiler and Pressure Vessel Code (hereafter called
4.1.2 Duplex (or Multiplex)—A strainer usually consisting
ASME Code) or ANSI/ASME B31.1. Bolts, screws, and
ofatleasttwobasketorelementchambersseparatedbyavalve fasteners in contact with interior fluid shall be of appropriate
(or valving) that permits continuous flow of fluid through one
corrosion-resistant material.
chamber while the other is accessible for cleaning.
6.2 The pressure ratings established under this specification
4.1.3 Automatic (Self-Cleaning)—Astrainerprovidingsome
are based on materials of high quality produced under regular
means for back-flushing or cleaning of the straining element
control of chemical and mechanical properties by a recognized
while the unit is in service. It can have one or more elements
process. The manufacturer shall be prepared to submit a
and may require periodic shutdown for maintenance and
certificate of compliance verifying that his product has been so
inspection.
produced and that it has been manufactured from material
4.2 Strainers may be further classified by pressure ratings
whose chemical and mechanical properties are at least equal to
and types of port connections, port alignments relative to unit
the requirements of the appropriate standard or specification.
center lines, cover closures, valve types (in duplex), types of
6.3 For materials not having values of allowable stress
baskets or elements, materials of construction, and other
tabulated in Section VIII, Division 1 of the ASME Code,
features of design.
allowable stresses shall be determined in accordance with the
procedures outlined in Subsection C and Appendix P of that
5. Ordering Information
section. Where it can be shown that the values of allowable
5.1 Ordersforproductsunderthisspecificationshallinclude stress listed for a particular material in one product form
the following information as applicable. If a manufacturer’s
(because of similar chemistry, mechanical properties, heat
standardized product is being ordered, include all data needed treatment, and so forth) are applicable to the same material in
b
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1199 − 88 (Reapproved 2010) F1199 − 88 (Reapproved 2015)An American National Standard
Standard Specification for
Cast (All Temperatures and Pressures) and Welded Pipe
Line Strainers (150 psig and 150°F Maximum)
This standard is issued under the fixed designation F1199; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers all cast strainers and welded strainers in services up to 150 psig and 150°F (1 MPa and 65°C). For
welded strainers used in services above 150 psig and 150°F, see Specification F1200.
1.2 This standard provides the minimum requirements for the design, fabrication, rating, marking, and testing of cast and welded
pipe line strainers for services above 0°F (−18°C).
1.3 Strainers manufactured to this specification are acceptable for use in the marine environment.
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2.1 ASTM Standards:
F1200 Specification for Fabricated (Welded) Pipe Line Strainers (Above 150 psig and 150°F)
2.2 ANSI Standards:
B2.1 Pipe Threads
B16.1 Cast Iron Pipe Flanges and Flanged Fittings
B16.3 Malleable Iron Threaded Fittings
B16.4 Cast Iron Threaded Fittings
B16.5 Steel Pipe Flanges and Flanged Fittings
B16.11 Forged Steel Fittings, Socket-Welding and Threaded
B16.15 Cast Bronze Threaded Fittings
B16.24 Bronze Pipe Flanges and Flanged Fittings
B16.25 Buttwelding Ends
B31.1 Power Piping
2.3 MSS Standards:
SP-51 150 lb Corrosion Resistant Cast Flanges and Flanged Fittings
SP-63 High Strength Wrought Welding Fittings
2.4 ASME Standard:Standards:
ASME Boiler and Pressure Vessel Code, Section VIII, Code Section VIII, Division 1, PressureVesselsPressure Vessels
This specification is under the jurisdiction of ASTM Committee F25 on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.11 on
Machinery and Piping Systems.
Current edition approved March 1, 2010May 1, 2015. Published April 2010June 2015. Originally approved in 1988. Last previous edition approved in 19982010 as
F1199 – 88 (2010).(2004). DOI: 10.1520/F1199-88R10.10.1520/F1199-88R15.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036.10036, http://www.ansi.org.
Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990.
Available from Manufacturers Standardization Society of the Valve and Fittings Industry (MSS), 127 Park St., NE, Vienna, VA 22180-4602.22180-4602,
http://www.mss-hq.org.
Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Two Park Ave., New York, NY 10016-5990, http://
www.asme.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F1199 − 88 (2015)
3. Terminology
3.1 Definitions:
3.1.1 basket or element—the replaceable part in a strainer that performs the barrier separation of solid particles from flowing
fluid. It is normally removable for cleaning and servicing and can be furnished in a wide variety of materials, particle size removal
capability, straining area, and types of construction. Interchangeable baskets or elements are normally available for a given make,
model, and size strainer.
3.1.2 maximum allowable working pressure (MAWP)—the highest internal pressure that the strainer can be subjected to in
service. The maximum nonshock working pressure for which a strainer is rated by the manufacturer.
3.1.3 maximum design temperature—the maximum temperature for which a strainer is rated by the manufacturer.
3.1.4 strainer—a device which, when installed in a pipe line, provides a mechanical means of removing solids from a flowing
liquid or gas by using a barrier element.
3.1.5 straining open area—the net effective open area of the clean element through which the fluid can pass.
4. Classification
4.1 Strainers may be classified into three general construction categories, simplex, duplex (or multiplex), and automatic
(self-cleaning), as follows:
4.1.1 Simplex—A strainer consisting of a single basket or element chamber that normally requires the flow through the unit to
be shut down before cleaning.
4.1.1.1 Classifications of simplex strainers based on port alignment relative to basket or element chamber are Y, T, Z, and others.
4.1.2 Duplex (or Multiplex)—A strainer usually consisting of at least two basket or element chambers separated by a valve (or
valving) that permits continuous flow of fluid through one chamber while the other is accessible for cleaning.
4.1.3 Automatic (Self-Cleaning)—A strainer providing some means for back-flushing or cleaning of the straining element while
the unit is in service. It can have one or more elements and may require periodic shutdown for maintenance and inspection.
4.2 Strainers may be further classified by pressure ratings and types of port connections, port alignments relative to unit center
lines, cover closures, valve types (in duplex), types of baskets or elements, materials of construction, and other features of design.
5. Ordering Information
5.1 Orders for products under this specification shall include the following information as applicable. If a manufacturer’s
standardized product is being ordered, include all data needed by the manufacturer to define the product.
5.1.1 Make.
5.1.2 Model (simplex or duplex).
5.1.3 Port size.
5.1.4 Port connections.
5.1.5 Maximum allowable pressure/temperature rating.
5.1.6 Body and cover material.
5.1.7 Type of cover closure.
5.1.8 Basket (element) material.
5.1.9 Basket hole size.
5.1.10 Optional design features.
5.1.11 Certification (see 8.1.2.1 and Section 9).
5.1.12 This ASTM standard designation number.
5.1.13 Additional requirements or testing as contracted by the manufacturer and purchaser.
5.2 If a product is to be specified by performance criteria rather than model description, then the following should be specified:
5.2.1 Maximum allowable clean pressure loss at a given flow capacity of a given liquid at a given velocity.
5.2.2 Temperature and pressure.
5.2.3 Straining area.
5.2.4 Minimum basket rupture differential pressure (see 7.4).
5.2.5 Maximum valve seepage rates (see 7.3).
5.2.6 Certification (see 6.2, 8.1.2.1, and Section 9).
5.2.7 For self-cleaning strainers, specify basket cleaning effectiveness and endurance testing.
5.3 In general, the standard product description should not be mixed with the performance criteria because conflicting
specifications can result (for example, maximum allowable pressure loss inconsistent with product size).
F1199 − 88 (2
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.