ASTM A1058-12a
(Test Method)Standard Test Methods for Mechanical Testing of Steel Products—Metric
Standard Test Methods for Mechanical Testing of Steel Products—Metric
SCOPE
1.1 These test methods cover mechanical tests described in ASTM, EN,2 ISO,3 and JIS4 standards that utilize the SI system of units. The test methods in each system are not exact equivalents. Each standards system (ASTM, EN, ISO, and JIS) shall be used independently of the other. Combining requirements from any two or more systems may result in nonconformance with the purchase order.
1.2 These test methods cover procedures for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control.
1.3 Only one of the testing procedure tracks shall be followed: ASTM, EN, ISO, or JIS. When a test method or practice is not available in one of the tracks then an appropriate test method or practice from an alternative track shall be used. The respective tests are listed in the column shown in Table 1.TABLE 1 Tests and Applicable Standards
Test
Sections
ASTM
EN
ISO
JIS
Tension
5 to 12
E8/E8M
10002-1
6892-1
Z 2241
Bend
13
E190
7438A
7438
Z 2248
E290
Bend (tube)
13
…
10232
8491
…
Hardness
14
Brinell
15
E10
6506-1A
6506-1
Z 2243
Rockwell
16
E18
6508-1A
6508-1
Z 2245
Portable
17
A833
…
…
…
E110
A1038
Impact
18 to 26
E23
10045-1
148-1
Z 2242
Keywords
27
…
…
…
… A These standards are designated EN ISO; this identifies the adoption of ISO standards by EN. “EN ISO” is part of the designation.Note 1—The test methods in each system are not exact equivalents.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 Attention is directed to Practice ISO 17025 when there may be a need for information on criteria for evaluation of testing laboratories.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A1058 − 12a AnAmerican National Standard
Standard Test Methods for
1
Mechanical Testing of Steel Products—Metric
This standard is issued under the fixed designation A1058; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.6 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
1.1 These test methods cover mechanical tests described in
2 3 4 responsibility of the user of this standard to establish appro-
ASTM,EN, ISO, andJIS standardsthatutilizetheSIsystem
priate safety and health practices and determine the applica-
of units. The test methods in each system are not exact
bility of regulatory limitations prior to use.
equivalents.Eachstandardssystem(ASTM,EN,ISO,andJIS)
shall be used independently of the other. Combining require-
2. Referenced Documents
ments from any two or more systems may result in noncon-
5
formance with the purchase order. 2.1 ASTM Standards:
A833Practice for Indentation Hardness of Metallic Materi-
1.2 Thesetestmethodscoverproceduresforthemechanical
als by Comparison Hardness Testers
testingofsteels,stainlesssteels,andrelatedalloys.Thevarious
A1038Test Method for Portable Hardness Testing by the
mechanical tests herein described are used to determine prop-
Ultrasonic Contact Impedance Method
erties required in the product specifications. Variations in
E8/E8MTest Methods for Tension Testing of Metallic Ma-
testing methods are to be avoided, and standard methods of
terials
testing are to be followed to obtain reproducible and compa-
E10Test Method for Brinell Hardness of Metallic Materials
rable results. In those cases in which the testing requirements
E18Test Methods for Rockwell Hardness of Metallic Ma-
forcertainproductsareuniqueoratvariancewiththesegeneral
terials
procedures,theproductspecificationtestingrequirementsshall
E23Test Methods for Notched Bar Impact Testing of Me-
control.
tallic Materials
1.3 Only one of the testing procedure tracks shall be
E29Practice for Using Significant Digits in Test Data to
followed: ASTM, EN, ISO, or JIS. When a test method or
Determine Conformance with Specifications
practiceisnotavailableinoneofthetracksthenanappropriate
E110Test Method for Indentation Hardness of Metallic
test method or practice from an alternative track shall be used.
Materials by Portable Hardness Testers
The respective tests are listed in the column shown in Table 1.
E190Test Method for Guided Bend Test for Ductility of
NOTE 1—The test methods in each system are not exact equivalents.
Welds
1.4 The values stated in SI units are to be regarded as E290Test Methods for Bend Testing of Material for Ductil-
standard. No other units of measurement are included in this ity
standard.
2.2 Other Documents:
ASME Boiler and Pressure Vessel CodeSection VIII, Divi-
1.5 Attention is directed to Practice ISO 17025 when there
6
sion I
may be a need for information on criteria for evaluation of
EN 10002-1Metallic Materials—Tensile Testing—Part 1:
testing laboratories.
Method of Test (at Ambient Temperature)
EN 10045-1Metallic Materials—Charpy Impact Test—Part
1: Test Method
1
These test methods are under the jurisdiction of ASTM Committee A01 on
EN 10045-2Charpy Impact Test on Metallic Materials—
Steel, Stainless Steel and Related Alloys and are the direct responsibility of
Subcommittee A01.13 on Mechanical and Chemical Testing and Processing Method for the Verification of Impact Testing Machines
Methods of Steel Products and Processes.
Current edition approved Oct. 1, 2012. Published October 2012. Originally
approved in 2008. Last previous edition approved in 2012 as A1058–12. DOI:
5
10.1520/A1058-12a. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
2
Available from British Standards Institute (BSI), 389 Chiswick High Rd., contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
London W4 4AL, U.K., http://www.bsi-global.com. Standards volume information, refer to the standard’s Document Summary page on
3
Available from International Organization for Standardization, 1 rue de the ASTM website.
6
Varembé, Case postale, CH-1211, Genève 20, Switzerland, http://www.iso.org. Available from American Society of Mechanical Engineers, ASME
4
Available from Japanese Standards Association, 4-1-24, Akasaka, Minato-ku, International, Three Park Avenue, New York, NY 10016-5990, USA, http://
Tokyo, 107-8440, Japan, http://www.jsa.or.jp. www.asme.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, We
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A1058 − 12 A1058 − 12a An American National Standard
Standard Test Methods for
1
Mechanical Testing of Steel Products—Metric
This standard is issued under the fixed designation A1058; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
2 3 4
1.1 These test methods cover mechanical tests described in ASTM, EN, ISO, and JIS standards that utilize the SI system of
units. The test methods in each system are not exact equivalents. Each standards system (ASTM, EN, ISO, and JIS) shall be used
independently of the other. Combining requirements from any two or more systems may result in nonconformance with the
purchase order.
1.2 These test methods cover procedures for the mechanical testing of steels, stainless steels, and related alloys. The various
mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing
methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In
those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the
product specification testing requirements shall control.
1.3 Only one of the testing procedure tracks shall be followed: ASTM, EN, ISO, or JIS. When a test method or practice is not
available in one of the tracks then an appropriate test method or practice from an alternative track shall be used. The respective
tests are listed in the column shown in Table 1.
NOTE 1—The test methods in each system are not exact equivalents.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 Attention is directed to Practice ISO 17025 when there may be a need for information on criteria for evaluation of testing
laboratories.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
5
2.1 ASTM Standards:
A833 Practice for Indentation Hardness of Metallic Materials by Comparison Hardness Testers
A1038 Test Method for Portable Hardness Testing by the Ultrasonic Contact Impedance Method
E8/E8M Test Methods for Tension Testing of Metallic Materials
E10 Test Method for Brinell Hardness of Metallic Materials
E18 Test Methods for Rockwell Hardness of Metallic Materials
E23 Test Methods for Notched Bar Impact Testing of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E110 Test Method for Indentation Hardness of Metallic Materials by Portable Hardness Testers
E190 Test Method for Guided Bend Test for Ductility of Welds
E290 Test Methods for Bend Testing of Material for Ductility
1
These test methods are under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and are the direct responsibility of Subcommittee
A01.13 on Mechanical and Chemical Testing and Processing Methods of Steel Products and Processes.
Current edition approved March 15, 2012Oct. 1, 2012. Published March 2012October 2012. Originally approved in 2008. Last previous edition approved in 20092012
as A1058 – 09.A1058 –12. DOI: 10.1520/A1058-12.10.1520/A1058-12a.
2
Available from British Standards Institute (BSI), 389 Chiswick High Rd., London W4 4AL, U.K., http://www.bsi-global.com.
3
Available from International Organization for Standardization, 1 rue de Varembé, Case postale, CH-1211, Genève 20, Switzerland, http://www.iso.org.
4
Available from Japanese Standards Association, 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440, Japan, http://www.jsa.or.jp.
5
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.