ASTM F914/F914M-14
(Test Method)Standard Test Method for Acoustic Emission for Aerial Personnel Devices Without Supplemental Load Handling Attachments
Standard Test Method for Acoustic Emission for Aerial Personnel Devices Without Supplemental Load Handling Attachments
SIGNIFICANCE AND USE
5.1 This test method provides a means of evaluating acoustic emissions generated by the rapid release of energy from localized sources within an aerial personnel device under controlled loading. The resultant energy releases occur during intentional application of a controlled predetermined load. These energy releases can be monitored and interpreted by qualified individuals.
5.2 This test method permits testing of the major components of an aerial personnel device under controlled loading. This test method utilizes objective criteria for evaluation and may be discontinued at any time to investigate a particular area of concern or prevent a fault from continuing to ultimate failure.
5.3 This test method provides a means of detecting acoustic emission sources that may be defects or irregularities, or both, affecting the structural integrity or intended use of the aerial personnel device.
5.4 Sources of acoustic emission found with this test method shall be evaluated by either more refined acoustic emission test methods or other nondestructive techniques (visual, liquid penetrant, radiography, ultrasonics, magnetic particle, etc.). Other nondestructive tests may be required to locate defects present in aerial personnel devices.
5.5 Defective areas found in aerial personnel devices by this test method should be repaired and retested as appropriate. Repair procedure recommendations are outside the scope of this test method.
SCOPE
1.1 This test method describes a procedure for non-destructive testing using acoustic emission (AE) testing for aerial personnel devices, which do not have a supplemental load handling attachment.
1.1.1 Equipment Covered—This test method covers the following types of vehicle-mounted insulated aerial personnel devices:
1.1.1.1 Extensible boom aerial personnel devices,
1.1.1.2 Articulating boom aerial personnel devices, and
1.1.1.3 Any combination of 1.1.1.1 and 1.1.1.2.
1.1.2 Equipment Not Covered—This test method does not cover any of the following equipment:
1.1.2.1 Material-handling aerial devices,
1.1.2.2 Digger-derricks with platform, and
1.1.2.3 Cranes with platform.
1.2 The AE test method is used to detect and area-locate emission sources. Verification of emission sources may require the use of other nondestructive test (NDT) methods, such as radiography, ultrasonics, magnetic particle, liquid penetrant, and visual inspection. Warning—This test method requires that external loads be applied to the superstructure of the vehicle under test. During the test, caution must be taken to safeguard personnel and equipment against unexpected failure or instability of the vehicle or components.Note 1—This test method is not intended to be a stand alone NDT method for the verification of the structural integrity of an aerial device. Other NDT methods should be used to supplement the results.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F914/F914M − 14
StandardTest Method for
Acoustic Emission for Aerial Personnel Devices Without
1
Supplemental Load Handling Attachments
This standard is issued under the fixed designation F914/F914M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
1.1 This test method describes a procedure for non-
responsibility of the user of this standard to establish appro-
destructive testing using acoustic emission (AE) testing for
priate safety and health practices and determine the applica-
aerial personnel devices, which do not have a supplemental
bility of regulatory limitations prior to use.
load handling attachment.
1.1.1 Equipment Covered—This test method covers the
2. Referenced Documents
following types of vehicle-mounted insulated aerial personnel
2
2.1 ASTM Standards:
devices:
E94Guide for Radiographic Examination
1.1.1.1 Extensible boom aerial personnel devices,
E114Practice for Ultrasonic Pulse-Echo Straight-Beam
1.1.1.2 Articulating boom aerial personnel devices, and
Contact Testing
1.1.1.3 Any combination of 1.1.1.1 and 1.1.1.2.
E164Practice for Contact Ultrasonic Testing of Weldments
1.1.2 Equipment Not Covered—This test method does not
E569Practice for Acoustic Emission Monitoring of Struc-
cover any of the following equipment:
tures During Controlled Stimulation
1.1.2.1 Material-handling aerial devices,
E610Terminology Relating to Acoustic Emission (With-
1.1.2.2 Digger-derricks with platform, and 3
drawn 1991)
1.1.2.3 Cranes with platform.
E650Guide for Mounting Piezoelectric Acoustic Emission
Sensors
1.2 The AE test method is used to detect and area-locate
emissionsources.Verificationofemissionsourcesmayrequire E750Practice for Characterizing Acoustic Emission Instru-
mentation
the use of other nondestructive test (NDT) methods, such as
radiography, ultrasonics, magnetic particle, liquid penetrant, E976GuideforDeterminingtheReproducibilityofAcoustic
and visual inspection. Warning—This test method requires Emission Sensor Response
E1417/E1417MPractice for Liquid Penetrant Testing
that external loads be applied to the superstructure of the
vehicle under test. During the test, caution must be taken to E1444/E1444MPractice for Magnetic Particle Testing
F2174Practice for Verifying Acoustic Emission Sensor Re-
safeguard personnel and equipment against unexpected failure
or instability of the vehicle or components. sponse
NOTE 1—This test method is not intended to be a stand alone NDT 2.2 ANSI Standard:
method for the verification of the structural integrity of an aerial device.
ANSI A92.2Standard for Vehicle-Mounted Elevating and
Other NDT methods should be used to supplement the results. 4
Rotating Aerial Devices
1.3 The values stated in either SI units or inch-pound units
2.3 ASNT Standard:
5
are to be regarded separately as standard. The values stated in ASNTRecommended Practice SNT-TC-1A
each system may not be exact equivalents; therefore, each
3. Terminology
system shall be used independently of the other. Combining
values from the two systems may result in non-conformance 3.1 Definitions:
with the standard.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
1
This test method is under the jurisdiction of ASTM Committee F18 on the ASTM website.
3
Electrical Protective Equipment for Workers and is the direct responsibility of Withdrawn. The last approved version of this historical standard is referenced
Subcommittee F18.55 on Inspection and Non-Destructive Test Methods for Aerial on www.astm.org.
4
Devices. Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
Current edition approved April 1, 2014. Published April 2014. Originally 4th Floor, New York, NY 10036, http://www.ansi.org.
5
approved in 1985. Last previous edition approved in 2010 as F914/F914M–10. AvailablefromAmericanSocietyforNondestructiveTesting(ASNT),P.O.Box
DOI: 10.1520/F0914_F0914M-14. 28518, 1711 Arlingate Ln., Columbus, OH 43228-0518, http://www.asnt.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F914/F914M − 14
3.1.1 acoustic emission (AE)—the class of phenomena period of time. The channel with a sensor closest to the
whereby elastic waves are generated by the ra
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F914/F914M − 10 F914/F914M − 14
Standard Test Method for
Acoustic Emission for Aerial Personnel Devices Without
1
Supplemental Load Handling Attachments
This standard is issued under the fixed designation F914/F914M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method describes a procedure for non-destructive testing using acoustic emission (AE) testing for aerial personnel
devices, which do not have a supplemental load handling attachment.
1.1.1 Equipment Covered—This test method covers the following types of vehicle-mounted insulated aerial personnel devices:
1.1.1.1 Extensible boom aerial personnel devices,
1.1.1.2 Articulating boom aerial personnel devices, and
1.1.1.3 Any combination of 1.1.1.1 and 1.1.1.2.
1.1.2 Equipment Not Covered—This test method does not cover any of the following equipment:
1.1.2.1 Material-handling aerial devices,
1.1.2.2 Digger-derricks with platform, and
1.1.2.3 Cranes with platform.
1.2 The AE test method is used to detect and area-locate emission sources. Verification of emission sources may require the use
of other nondestructive test (NDT) methods, such as radiography, ultrasonics, magnetic particle, liquid penetrant, and visual
inspection. Warning—This test method requires that external loads be applied to the superstructure of the vehicle under test.
During the test, caution must be taken to safeguard personnel and equipment against unexpected failure or instability of the vehicle
or components.
NOTE 1—This test method is not intended to be a stand alone NDT method for the verification of the structural integrity of an aerial device. Other NDT
methods should be used to supplement the results.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
E94 Guide for Radiographic Examination
E114 Practice for Ultrasonic Pulse-Echo Straight-Beam Contact Testing
E164 Practice for Contact Ultrasonic Testing of Weldments
E569 Practice for Acoustic Emission Monitoring of Structures During Controlled Stimulation
3
E610 Terminology Relating to Acoustic Emission (Withdrawn 1991)
E650 Guide for Mounting Piezoelectric Acoustic Emission Sensors
E750 Practice for Characterizing Acoustic Emission Instrumentation
E976 Guide for Determining the Reproducibility of Acoustic Emission Sensor Response
1
This test method is under the jurisdiction of ASTM Committee F18 on Electrical Protective Equipment for Workers and is the direct responsibility of Subcommittee
F18.55 on Inspection and Non-Destructive Test Methods for Aerial Devices.
Current edition approved April 1, 2010April 1, 2014. Published May 2010April 2014. Originally approved in 1985. Last previous edition approved in 20032010 as
F914 – 03.F914/F914M – 10. DOI: 10.1520/F0914-10.10.1520/F0914_F0914M-14.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn. The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F914/F914M − 14
E1417/E1417M Practice for Liquid Penetrant Testing
E1444/E1444M Practice for Magnetic Particle Testing
F2174 Practice for Verifying Acoustic Emission Sensor Response
2.2 ANSI Standard:
4
ANSI A92.2 Standard for Vehicle-Mounted Elevating and Rotating Aerial Devices
2.3 ASNT Standard:
5
ASNT Recommended Practice SNT-TC-1A
3. Terminology
3.1 Definitions:
3.1.1 acoustic emission (AE)—the class of phenomena whereby e
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.