iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D2484-00

(Specification)

Standard Specification for Polyester Film Pressure-Sensitive Electrical Insulating Tape

Standard Specification for Polyester Film Pressure-Sensitive Electrical Insulating Tape

SCOPE
1.1 This specification covers electrical insulating tape consisting of a polyester plastic film coated on one side with a pressure-sensitive adhesive.  
1.2 The values stated in inch-pound units are to be regarded as the standard.

General Information

Status
Historical
Publication Date
09-Apr-2000
ICS
29.035.20 - Plastics and rubber insulating materials
Technical Committee
D09 - Electrical and Electronic Insulating Materials
Drafting Committee
D09.07 - Electrical Insulating Materials
Current Stage
Ref Project

Relations

Replaced By
ASTM D2484-06 - Standard Specification for Polyester Film Pressure-Sensitive Electrical Insulating Tape
Effective Date
01-Oct-2006

Buy Standard

ASTM D2484-00 - Standard Specification for Polyester Film Pressure-Sensitive Electrical Insulating TapeASTM D2484-00 - Standard Specification for Polyester Film Pressure-Sensitive Electrical Insulating Tape
PreviousNext
Technical specification
ASTM D2484-00 - Standard Specification for Polyester Film Pressure-Sensitive Electrical Insulating Tape
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: D 2484 – 00
Standard Specification for
Polyester Film Pressure-Sensitive Electrical Insulating Tape
This standard is issued under the fixed designation D 2484; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope 4.1.1 Type 1—General-purpose tape, nominal thickness
0.06 mm (0.0025 in.) and coated with a thermoplastic adhesive
1.1 This specification covers electrical insulating tape con-
which is not chemically heat reactive.
sisting of a polyester plastic film coated on one side with a
4.1.2 Type 2—General-purpose tape, nominal thickness
pressure-sensitive adhesive.
0.06 mm (0.0025 in.) and coated with a heat-reactive thermo-
1.2 The values stated in SI units are to be regarded as the
setting adhesive.
standard. The values given in parenthesis are provided for
4.1.3 Type 3—General-purpose tape, nominal thickness
information only.
0.09 mm (0.0035 in.) and coated with a heat-reactive thermo-
NOTE 1—This standard and IEC 60454–3–2 and –3 are similar but not
setting adhesive.
equivalent in all details.
4.1.4 Type 4—General-purpose tape, nominal thickness
0.025 mm (0.0010 in.) and coated with a heat-reactive ther-
2. Referenced Documents
mosetting adhesive.
2.1 ASTM Standards:
D 1000 Test Methods for Pressure-Sensitive Adhesive-
5. Materials and Manufacture
Coated Tapes Used for Electrical and Electronic Applica-
5.1 The polymer used as the backing shall be clear polyeth-
tions
ylene terephthalate sheet.
D 1711 Terminology Relating to Electrical Insulation
5.2 The pressure-sensitive adhesive coating shall be free
D 2305 Test Methods for Polymeric Films Used for Elec-
from lumps and bare spots. There shall be no adhesive transfer
trical Insulation
when tape is unwound from the roll.
2.2 IEC Standard:
5.3 Both transparent and colored tapes are available.
Publication 60454–3 Specifications for Pressure-Sensitive
5.3.1 Type 1—Transparent.
Adhesive Tapes for Electrical Purposes. Sheet 2: Require-
5.3.2 Types 2, 3, and 4—Transparent and colors.
ments for Polyester Film Tapes (PETP) with Thermoset-
ting Adhesive. Sheet 3: Requirements for Polyester Film
6. Standard Rolls
Tapes (PETP) with Non-Thermosetting Adhesive
6.1 The standard widths and lengths shall be selected from
the following:
3. Terminology
6.1.1 Widths:
3.1 Definitions— For definitions of terms used in this
mm in. mm in.
specification, refer to Terminology D 1711.
1 7
6 ⁄4 22 ⁄8
9 ⁄8 25 1
4. Classification 1 1
12 ⁄2 30 1 ⁄4
5 1
15 ⁄8 38 1 ⁄2
4.1 This specification includes the requirements for four
19 ⁄4 50 2
types as follows:
Widths greater than 50 mm (2 in.) shall be agreed upon
between the purchaser and the seller.
6.1.2 Lengths:
This specification is under the jurisdiction of ASTM Committee D-09 on
mft
Electrical and Electronic Insulating Materials and is the direct responsibility of
33 108
Subcommittee D09.07 on Flexible and Rigid Insulating Materials.
50 164
Current edition approved April 10, 2000. Published June 2000. Originally 55 180
published as D 2484 – 66 T. Last previous edition D 2484 – 94. 66 216
Annual Book of ASTM Standards, Vol 10.01.
6.2 Non-standard widths and lengths are permissible if
Available from American National Standards Institute, 11 W. 42nd St., 13th
Floor, New York, NY 10036. agreed upon between the purchaser and seller.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
D2484–00
7. Requiremen
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D3005-24(Specification)
Standard Specification for Low-Temperature Resistant Vinyl Chloride Plastic Pressure-Sensitive Electrical Insulating Tape

ABSTRACT
This specification covers the properties and requirements for electrical insulating tape consisting of a backing of vinyl chloride plastic, coated on one side with a pressure-sensitive adhesive, for use at low temperatures. Four types are included providing two thicknesses at two operating temperatures. Selected from standard widths and lengths, the tapes shall conform to specified values of the following requirements: break strength; break and static elongation; dielectric breakdown; adhesion to both steel and backing; roll unwind; high-humidity insulation resistance; flammability; and behavior during flagging test.
SCOPE
1.1 This specification covers an electrical insulating tape for use at low temperature down to approximately -18 °C (0 °F). The tape consists of a backing of vinyl chloride plastic, coated on one side with a pressure-sensitive adhesive. Four types are included providing two thicknesses at two operating temperatures.  
1.2 The values stated in SI units are the standard. The values given in parentheses are provided for information purposes only.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2301-24(Specification)
Standard Specification for Vinyl Chloride Plastic Pressure-Sensitive Electrical Insulating Tape

ABSTRACT
This specification covers electrical insulating tape consisting of a flexible backing made from vinyl chloride plastic coated on one side with a pressure-sensitive adhesive. The tape shall be classified according to thickness: Type I and Type II. The backing shall be polyvinyl chloride plastic suitably compounded to meet the requirements of this specification. The backing shall be smooth and uniform. The selection of rolls, conditioning, and testing shall be in accordance with the specified requirements.
SCOPE
1.1 This specification covers electrical insulating tape consisting of a flexible backing made from vinyl chloride plastic coated on one side with a pressure-sensitive adhesive.  
1.2 The values stated in SI units are the standard. The values given in parentheses are provided for information purposes only.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2655-23(Specification)
Standard Specification for Crosslinked Polyethylene Insulation for Wire and Cable Rated 0 to 2000 V, 90 °C Operation

ABSTRACT
This specification covers crosslinked polymer insulation material consisting substantially of polyethylene or a polyethylene copolymer for electrical wires and cables in conductor, suitable for continuous use on power cables in wet and dry locations, having specified sizes and operating at specified voltage ratings and conductor temperatures. Materials covered by this specification are not sunlight and weather resistant unless they are carbon black pigmented or contain an additive system designed for this protection. Since the insulation cannot be tested unless it has been formed around a conductor, tests shall then be done on insulated wire solely to determine the relevant property of the insulation and not to test the conductor or completed cable. Materials shall meet the physical properties as follows: unaged tensile strength and elongation at rupture; tensile strength and elongation at rupture after air oven aging; heat distortion; filled and unfilled percent hot creep; and filled and unfilled percent hot set. Insulations shall also perform satisfactorily during tests for AC and DC voltage, insulation resistance, and accelerated water absorption.
SCOPE
1.1 This specification covers a crosslinked polyethylene insulation for electrical wires and cables in conductor sizes 14 AWG [2.08 mm2] and larger. The base polymer of this insulation consists substantially of polyethylene or a polyethylene copolymer.  
1.2 This type of insulation is suitable for continuous use on power cables in wet and dry locations, for voltage ratings not exceeding 2000 V and at conductor temperatures not exceeding 90 °C for normal operation. For copper conductors, the insulation can be applied over the uncoated metal.  
1.3 Materials covered by this specification are not sunlight and weather resistant unless they are carbon black pigmented or contain an additive system designed for this protection.  
1.4 In many instances the insulation cannot be tested unless it has been formed around a conductor. Therefore, tests are done on insulated wire in this standard solely to determine the relevant property of the insulation and not to test the conductor or completed cable.  
1.5 Whenever two sets of values are presented, in different units, the values in the first set are the standard, while those in parentheses are for information only.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3144-23(Specification)
Standard Specification for Crosslinked Poly(Vinylidene Fluoride) and Poly(Vinylidene Fluoride) Copolymer Heat-Shrinkable Tubing for Electrical Insulation

ABSTRACT
This specification covers semirigid, flame-retardant, crosslinked poly(vinylidene fluoride) heat-shrinkable tubing for electrical insulation purposes. It is supplied in an expanded form and will shrink to its extruded diameter when heated. The tubing shall be extruded, crosslinked, and then expanded to the required dimensions. The material shall conform to the chemical property requirements specified. Every lot of material manufactured shall be tested for restricted shrinkage, heat shock, tensile strength, and elongation to conform to the mechanical, thermal, electrical requirements.
SCOPE
1.1 This specification covers semirigid, flame-retardant, crosslinked poly(vinylidene fluoride) heat-shrinkable tubing for electrical insulation purposes. It is supplied in an expanded form and will shrink to its extruded diameter when heated.
Note 1: This standard is similar but not identical to IEC 60684–3–228.  
1.2 The values stated in inch-pound units are to be regarded as the standard, except temperature which shall be stated in degrees Celsius. Values in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D922-23(Specification)
Standard Specification for Nonrigid Vinyl Chloride Polymer Tubing

ABSTRACT
This specification covers three grades of nonrigid tubing of vinyl chloride polymer or its copolymers with other materials for use in electrical insulation. Clear transparent, black, white, yellow, green, blue, and red shall be considered standard colors. Colors other than these shall be considered special. Dimensional requirements to which tubing shall adhere are inside diameter, wall thickness, and commercial lengths. The tubing shall also conform to physical and electrical requirements, as follows: flammability; tensile strength; effect of elevated temperatures; ultimate elongation after immersion in oil; brittleness temperature; penetration resistance; volume resistivity; dielectric breakdown at high humidity; strain relief; and corrosive effect.
SCOPE
1.1 This specification covers nonrigid tubing of vinyl chloride polymer or its copolymers with other materials for use in electrical insulation in three grades, as follows:  
1.1.1 Grade A—General-purpose.  
1.1.2 Grade B—Low-temperature.  
1.1.3 Grade C—High-temperature.  
1.2 This standard and IEC-60684-3-100 to -105 address the same subject matter but differ in technical content.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D2148-22(Test Method)
Standard Test Methods for Bondable Silicone Rubber Tapes Used for Electrical Insulation

SIGNIFICANCE AND USE
5.1 Self-adhesion is a primary initial property since it affects layer-to-layer bonding. The integrity of the bond can significantly affect the electrical and physical performance of the insulation system. Therefore, the degree of self-adhesion is directly related to apparatus performance.  
5.2 A high degree of self-adhesion is desirable for most electrical applications. In this test, a short unwinding length indicates a high degree of self-adhesion.  
5.3 This test method has been found useful as a quality control test for lot acceptance.
SCOPE
1.1 These test methods cover tests for bondable silicone rubber tapes which form a sealed structure either with the application of heat (and pressure if needed) or by the process of auto-adhesion (self-fusing).  
1.2 These test methods appear in the following sections:    
Test Method  
Section  
Adhesion  
3 – 10  
Bond Strength  
11 – 18  
Dielectric Breakdown Voltage  
19 – 26  
Hardness  
41  
Length  
33 and 34  
Thickness  
27 – 32  
Width  
36 – 40  
1.3 Units—The values stated in SI units are the standard. The inch-pound units in parentheses are for information only. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  For a specific hazard statement see 23.1.1.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D4313-22(Specification)
Standard Specification for General-Purpose, Heavy-Duty, and Extra-Heavy-Duty Crosslinked Chlorinated Polyethylene (CPE) Jackets For Wire and Cable

ABSTRACT
This specification covers crosslinked chlorinated polyethylene compounds intended for use as jacket materials (outer coverings) on electrical wires and cables for general-purpose, heavy-duty, and extra-heavy-duty service. The materials under this specification, however, are not recommended for applications with very low temperature service requirement. Physical tests shall be performed and shall conform to the physical property requirements specified such as tensile strength, tensile stress at elongation, elongation at rupture, and tension set. Per service requirement, additional tests for sunlight and weather resistance shall be performed as well, and shall conform to the tensile strength and elongation requirements specified.
SCOPE
1.1 This specification covers crosslinked chlorinated polyethylene (CPE) compounds suitable for use as outer coverings or jackets on electrical cables for general-purpose, heavy-duty, and extra-heavy-duty service.  
1.2 These jacket materials are not recommended for use on cables which are to be installed at a temperature less than –25 °C.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4363-22(Specification)
Standard Specification for Thermoplastic Chlorinated Polyethylene (CPE) Jacket for Wire and Cable

ABSTRACT
This specification covers thermoplastic chlorinated polyethylene (CM) compounds suitable for use as an outer covering or jacket on electrical cables. Thermoplastic jackets shall conform to the requirements for physical properties specified. The sunlight and weather resistance of the jackets shall be tested to meet the requirements specified.
SCOPE
1.1 This specification covers thermoplastic chlorinated polyethylene (CPE) compounds suitable for use as an outer covering or jacket on electrical cables.  
1.2 These jacket materials are suitable for use on cables which will be installed at temperatures above –35 °C.  
1.3 The values stated in inch-pound units are regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2902-21(Specification)
Standard Specification for Fluoropolymer Resin Heat-Shrinkable Tubing for Electrical Insulation

ABSTRACT
This specification applies to flexible fluoropolymer resin heat-shrinkable extruded tubing made from tetrafluoroethylene resin, copolymer of tetrafluoroethylene and hexafluoropropylene (FEP), and from perfluoroalkoxy (PFA) resin for use as electrical insulation. This specification covers three types of tubings, namely: Type I tubing, normally made by paste extrusion, and Type II and Type III tubings, normally made by melt extrusion. The finished compound shall be free of all foreign matter other than intended formulation additives. The material shall conform to the specified chemical and physical property requirements such as: (1) restricted shrinkage, (2) specific gravity, (3) longitudinal change, (4) tensile modulus at elongation, (5) volume resistivity, (6) dielectric breakdown voltage, (7) heat resistance, (8) low-temperature flexibility, and (9) melting point. The dimensional requirements after unrestrictive shrinkage such as inside diameter, wall thickness, and stock lengths are specified. The sampling and test methods to determine conformance to the specified requirements are given.
SCOPE
1.1 This specification applies to flexible heat-shrinkable extruded tubing made from tetrafluoroethylene resin, copolymer of tetrafluoroethylene and hexafluoropropylene, and from perfluoroalkoxy resin for use as electrical insulation. This specification excludes crosslinked poly(vinylidene fluoride) and poly(vinylidene fluoride) copolymer which are covered under Specification D3144.
Note 1: This standard is similar but not identical to IEC 60684-3-240.  
1.2 The values stated in inch-pound units are to be regarded as standard, except temperature, which shall be stated in degrees Celsius. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D1047-21(Specification)
Standard Specification for Poly(Vinyl Chloride) Jacket for Wire and Cable

ABSTRACT
This specification covers a durable general-purpose thermoplastic jacket made from poly(vinyl chloride) or the copolymer of vinyl chloride and vinyl acetate for use in wires and cables at specified minimum installing temperature. The jackets shall meet specified values of the following physical and electrical properties: unexposed (unaged) tensile strength and elongation at rupture; tensile strength and elongation at rupture after air oven aging and oil immersion tests; heat distortion; heat shock; cold bend; surface resistivity; and U-bend discharge at required cable insulation AC test voltage.
SCOPE
1.1 This specification covers a durable general-purpose thermoplastic jacket made from poly(vinyl chloride) or the copolymer of vinyl chloride and vinyl acetate suitable for a minimum installing temperature of −10 °C.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off