ASTM F2363/F2363M-17
(Specification)Standard Specification for Sewage and Graywater Flow Through Treatment Systems
Standard Specification for Sewage and Graywater Flow Through Treatment Systems
ABSTRACT
This specification covers the material, design, manufacture, performance, operation, functioning, and testing requirements for United States Coast Guard (USCG) Type II Marine Sanitation Devices or IMO MARPOL 73/78 Annex IV flow through treatment device intended to process sewage and graywater generated during the ship's normal service. It is intended for use by purchasers, designers, and manufacturers of shipboard environmental pollution control equipment to determine the requirements for equipment purchase, equipment use, and design considerations. The marine sanitation devices shall perform accordingly to the following tests: vibration test; shock test; rolling test; pressure test; pressure and vacuum pulse test; temperature range test; chemical resistance test; operability test; sewage processing test; coliform test; suspended solids test; and ignition prevention test. Aside from meeting the requirements set forth herein, the devices shall also be designed and installed to conform to human engineering principles to th degree that it can be operated and maintained by males and females of specified heights.
SCOPE
1.1 This specification covers the design, manufacture, performance, operation, and testing of flow through treatment systems intended to process sewage or graywater, or both, generated during a ship's normal service. This specification is intended for use by designers, manufacturers, purchasers, and operators of shipboard environmental pollution control equipment to determine the requirements for equipment design, manufacture, purchase, and in-service operation.
1.2 The treatment system shall be capable of meeting the effluent requirements detailed in Section 4 with respect to a ship's operational area.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F2363/F2363M − 17 An American National Standard
Standard Specification for
1
Sewage and Graywater Flow Through Treatment Systems
This standard is issued under the fixed designation F2363/F2363M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
Shipboard treatment of wastewater has evolved over the years from systems using maceration and
chlorination techniques to more advanced biological systems that are designed to treat a single
wastestream of sewage followed more recently by complex bio-reactor systems employing advanced
oxidation and high-powered UV systems that are designed to remove organic and inorganic materials
from a combined wastestream of sewage and graywater.
Advancements in treatment technologies have been fueled, in part, by shipping companies wanting
to adopt more environmentally friendly practices as well as by regulatory bodies imposing more
stringent standards on wastewater discharges from ships.
This standard is a consolidated source of sewage and graywater treatment system requirements that
combines international requirements in MARPOL Annex IV with requirements of other regulatory
bodies and overlays industry best practices.
1. Scope 1.5 This international standard was developed in accor-
dance with internationally recognized principles on standard-
1.1 This specification covers the design, manufacture,
ization established in the Decision on Principles for the
performance, operation, and testing of flow through treatment
Development of International Standards, Guides and Recom-
systems intended to process sewage or graywater, or both,
mendations issued by the World Trade Organization Technical
generated during a ship’s normal service. This specification is
Barriers to Trade (TBT) Committee.
intended for use by designers, manufacturers, purchasers, and
operators of shipboard environmental pollution control equip-
2. Referenced Documents
ment to determine the requirements for equipment design,
2
2.1 ASTM Standards:
manufacture, purchase, and in-service operation.
A307 Specification for Carbon Steel Bolts, Studs, and
1.2 The treatment system shall be capable of meeting the
Threaded Rod 60 000 PSI Tensile Strength
effluent requirements detailed in Section 4 with respect to a
A563 Specification for Carbon and Alloy Steel Nuts
ship’s operational area.
B117 Practice for Operating Salt Spray (Fog) Apparatus
1.3 The values stated in either SI units or inch-pound units
B165 Specification for Nickel-Copper Alloy (UNS N04400)
are to be regarded separately as standard. The values stated in
Seamless Pipe and Tube
each system may not be exact equivalents; therefore, each
D1253 Test Method for Residual Chlorine in Water
system shall be used independently of the other. Combining
E11 Specification for Woven Wire Test Sieve Cloth and Test
values from the two systems may result in non-conformance
Sieves
with the standard.
F906 Specification for Letters and Numerals for Ships
F992 Specification for Valve Label Plates
1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the F993 Specification for Valve Locking Devices
F998 Specification for Centrifugal Pump, Shipboard Use
responsibility of the user of this standard to establish appro-
F1030 Practice for Selection of Valve Operators
priate safety, health, and environmental practices and deter-
F1098 Specification for Envelope Dimensions for Butterfly
mine the applicability of regulatory limitations prior to use.
Valves—NPS 2 to 24
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships
and Marine Technology and is the direct responsibility of Subcommittee F25.06 on
2
Marine Environmental Protection. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Nov. 15, 2017. Published December 2017. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2004. Last previous edition approved in 2012 as F2363 – 12. Standards volume information, refer to the standard’s Document Summary page on
DOI:10.1520/F2363_F2363M-17. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2363/F2363M − 17
F1122 Specification for Quick Disconnect Couplings (6 in. ANSI/ASSE 1013 Performance requirements for reduced
NPS and Smaller) pressure principle backflow preventers and reduced pres-
5
F1155 Practice for Selection and Application of Piping sure
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2363/F2363M − 12 F2363/F2363M − 17 An American National Standard
Standard Specification for
1
Sewage and Graywater Flow Through Treatment Systems
This standard is issued under the fixed designation F2363/F2363M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
Shipboard treatment of wastewater has evolved over the years from systems using maceration and
chlorination techniques to more advanced biological systems that are designed to treat a single
wastestream of sewage followed more recently by complex bio-reactor systems employing advanced
oxidation and high-powered UV systems that are designed to remove organic and inorganic materials
from a combined wastestream of sewage and graywater.
Advancements in treatment technologies have been fueled, in part, by shipping companies wanting
to adopt more environmentally friendly practices as well as by regulatory bodies imposing more
stringent standards on wastewater discharges from ships.
This standard is a consolidated source of sewage and graywater treatment system requirements that
combines international requirements in MARPOL Annex IV with requirements of other regulatory
bodies and overlays industry best practices.
1. Scope
1.1 This specification covers the design, manufacture, performance, operation, and testing of flow through treatment systems
intended to process sewage or graywater, or both, generated during a ship’s normal service. This specification is intended for use
by designers, manufacturers, purchasers, and operators of shipboard environmental pollution control equipment to determine the
requirements for equipment design, manufacture, purchase, and in-service operation.
1.2 The treatment system shall be capable of meeting the effluent requirements detailed in Section 4 with respect to a ship’s
operational area.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A307 Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile Strength
A563 Specification for Carbon and Alloy Steel Nuts
B117 Practice for Operating Salt Spray (Fog) Apparatus
B165 Specification for Nickel-Copper Alloy (UNS N04400) Seamless Pipe and Tube
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.06 on Marine
Environmental Protection.
Current edition approved May 1, 2012Nov. 15, 2017. Published June 2012December 2017. Originally approved in 2004. Last previous edition approved in 20062012 as
F2363 – 06.F2363 – 12. DOI:10.1520DOI:10.1520/F2363_F2363M-17.⁄F2363_F2363M-12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2363/F2363M − 17
D1253 Test Method for Residual Chlorine in Water
E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves
F906 Specification for Letters and Numerals for Ships
F992 Specification for Valve Label Plates
F993 Specification for Valve Locking Devices
F998 Specification for Centrifugal Pump, Shipboard Use
F1030 Practice for Selection of Valv
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.