ASTM B705-17
(Specification)Standard Specification for Nickel-Alloy (UNS N06625, N06219 and N08825) Welded Pipe
Standard Specification for Nickel-Alloy (UNS N06625, N06219 and N08825) Welded Pipe
ABSTRACT
This specification covers UNS N06625, N06219, and N08825 nickel-alloy welded pipe in the annealed condition. The pipe shall be manufactured from flat-rolled alloy by an automatic welding process with no additional filler metal. The pipe material shall be cold-worked, annealed, and nondestructively tested. The pipe shall be furnished with oxide removed. The material shall conform to the composition required by the specification. The pipe shall be subjected to tensile, yield, elongation, transverse guided bend, and nondestructive test requirements. Nondestructive test includes hydrostatic, pneumatic, eddy current, ultrasonic, leak, and electric testing. Acceptable size limit of cracks or other defect after bending test is specified.
SCOPE
1.1 This specification covers welded UNS N06625,2 UNS N062192 and UNS N088252 pipe in the annealed condition (temper) for general corrosion applications.
1.2 This specification covers pipe sizes in schedules shown in the Permissible Variations in Outside Diameter and Wall Thickness for Welded Pipe table of Specification B775.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 The following precautionary caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:B705 −17
Standard Specification for
Nickel-Alloy (UNS N06625, N06219 and N08825) Welded
1
Pipe
This standard is issued under the fixed designation B705; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* Check Analysis Limits for Nickel, Nickel Alloys and
2 Cobalt Alloys
1.1 This specification covers welded UNS N06625, UNS
4
2 2
2.2 ASME Boiler and Pressure Vessel Code:
N06219 and UNS N08825 pipe in the annealed condition
Section IX Welding and Brazing Qualifications
(temper) for general corrosion applications.
1.2 This specification covers pipe sizes in schedules shown
3. General Requirement
in the Permissible Variations in Outside Diameter and Wall
3.1 Material furnished in accordance with this specification
Thickness for Welded Pipe table of Specification B775.
shall conform to the applicable requirements of the current
1.3 The values stated in inch-pound units are to be regarded
edition of Specification B775 unless otherwise provided
as standard. The values given in parentheses are mathematical
herein.
conversions to SI units that are provided for information only
and are not considered standard. 4. Definition of Terms
1.4 The following precautionary caveat pertains only to the
4.1 Class 1—Welded, cold-worked, annealed, and nonde-
test methods portion, Section 8, of this specification: This
structively tested in accordance with 9.1.
standard does not purport to address all of the safety concerns,
4.2 Class 2—Welded, cold-worked, annealed, and nonde-
if any, associated with its use. It is the responsibility of the user
structively tested in accordance with 9.2.
of this standard to establish appropriate safety, health, and
4.3 Grade 1—Annealed condition, relevant for UNS
environmental practices and determine the applicability of
N06625.
regulatory limitations prior to use.
1.5 This international standard was developed in accor-
4.4 Grade 2—Solution annealed condition, relevant for
dance with internationally recognized principles on standard-
UNS N06625.
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom- 5. Ordering Information
mendations issued by the World Trade Organization Technical
5.1 It is the responsibility of the purchaser to specify all
Barriers to Trade (TBT) Committee.
requirements that are necessary for the safe and satisfactory
performance of material ordered under this specification.
2. Referenced Documents
Examples of such requirements include, but are not limited to,
3
2.1 ASTM Standards:
the following:
B775 Specification for General Requirements for Nickel and
5.1.1 Alloy name or UNS number,
Nickel Alloy Welded Pipe
5.1.2 ASTM designation,
B880 Specification for General Requirements for Chemical
5.1.3 Dimensions:
5.1.3.1 Pipe size,
5.1.3.2 Length (specific or random),
1
This specification is under the jurisdiction of ASTM Committee B02 on
5.1.4 Class (see Section 3),
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
5.1.5 Grade if UNS N06625 is specified. If neither grade of
B02.07 on Refined Nickel and Cobalt and Their Alloys.
Current edition approved Nov. 1, 2017. Published November 2017. Originally N06625 is specified, grade 1 will be supplied.
approved in 1982. Last previous edition approved in 2014 as B705 – 05 (2014).
5.1.6 Quantity (feet or number of pieces),
DOI: 10.1520/B0705-17.
5.1.7 Certification—State if certification is required,
2
New designation established in accordance with Practice E527 and SAE
J 1086, Practice for Numbering Metals and Alloys (UNS).
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from American Society of Mechanical Engineers (ASME), ASME
Standards volume information, refer to the standard’s Document Summary page on International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
theASTM website. www.asme.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B705−17
TABLE 2 Mechanical Property Requirements
5.1.8 Samples for Product (Check) Analysis—State whether
samples for product (check) analysis should be furnished (7.2), Yield Elonga-
Tensile Strength tionin2
and
Alloy Grade Strength
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B705 − 05 (Reapproved 2014) B705 − 17
Standard Specification for
Nickel-Alloy (UNS N06625, N06219 and N08825) Welded
1
Pipe
This standard is issued under the fixed designation B705; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
2 2 2
1.1 This specification covers welded UNS N06625, UNS N06219 and UNS N08825 pipe in the annealed condition (temper)
for general corrosion applications.
1.2 This specification covers pipe sizes in schedules shown in the Permissible Variations in Outside Diameter and Wall
Thickness for Welded Pipe table of Specification B775.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 The following precautionary caveat pertains only to the test methods portion, Section 8, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for
this product/material as provided by the manufacturer, to establish appropriate safety and health practices,establish appropriate
safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
B751 Specification for General Requirements for Nickel and Nickel Alloy Welded Tube
B775 Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe
B880 Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys
4
2.2 ASME Boiler and Pressure Vessel Code:
Section IX Welding and Brazing Qualifications
3. General Requirement
3.1 Material furnished in accordance with this specification shall conform to the applicable requirements of the current edition
of Specification B775 unless otherwise provided herein.
4. Definition of Terms
4.1 Class 1—Welded, cold-worked, annealed, and nondestructively tested in accordance with 9.1.
4.2 Class 2—Welded, cold-worked, annealed, and nondestructively tested in accordance with 9.2.
4.3 Grade 1—Annealed condition, relevant for UNS N06625.
1
This specification is under the jurisdiction of ASTM Committee B02 on Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee B02.07 on Refined
Nickel and Cobalt and Their Alloys.
Current edition approved Oct. 1, 2014Nov. 1, 2017. Published October 2014November 2017. Originally approved in 1982. Last previous edition approved in 20092014
as B705 – 05 (2009).(2014). DOI: 10.1520/B0705-05R14.10.1520/B0705-17.
2
New designation established in accordance with Practice E527 and SAE J 1086, Practice for Numbering Metals and Alloys (UNS).
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
www.asme.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B705 − 17
4.4 Grade 2—Solution annealed condition, relevant for UNS N06625.
5. Ordering Information
5.1 It is the responsibility of the purchaser to specify all requirements that are necessary for the safe and satisfactory
performance of material ordered under this specification. Examples of such requirements include, but are not limited to, the
following:
5.1.1 Alloy name or UNS number,
5.1.2 ASTM designation,
5.1.3 Dimensions
...
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B705 − 17
Standard Specification for
Nickel-Alloy (UNS N06625, N06219 and N08825) Welded
1
Pipe
This standard is issued under the fixed designation B705; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* Check Analysis Limits for Nickel, Nickel Alloys and
2 Cobalt Alloys
1.1 This specification covers welded UNS N06625, UNS
4
2 2
2.2 ASME Boiler and Pressure Vessel Code:
N06219 and UNS N08825 pipe in the annealed condition
Section IX Welding and Brazing Qualifications
(temper) for general corrosion applications.
1.2 This specification covers pipe sizes in schedules shown
3. General Requirement
in the Permissible Variations in Outside Diameter and Wall
3.1 Material furnished in accordance with this specification
Thickness for Welded Pipe table of Specification B775.
shall conform to the applicable requirements of the current
1.3 The values stated in inch-pound units are to be regarded
edition of Specification B775 unless otherwise provided
as standard. The values given in parentheses are mathematical
herein.
conversions to SI units that are provided for information only
and are not considered standard.
4. Definition of Terms
1.4 The following precautionary caveat pertains only to the
4.1 Class 1—Welded, cold-worked, annealed, and nonde-
test methods portion, Section 8, of this specification: This
structively tested in accordance with 9.1.
standard does not purport to address all of the safety concerns,
4.2 Class 2—Welded, cold-worked, annealed, and nonde-
if any, associated with its use. It is the responsibility of the user
structively tested in accordance with 9.2.
of this standard to establish appropriate safety, health, and
4.3 Grade 1—Annealed condition, relevant for UNS
environmental practices and determine the applicability of
N06625.
regulatory limitations prior to use.
1.5 This international standard was developed in accor-
4.4 Grade 2—Solution annealed condition, relevant for
dance with internationally recognized principles on standard-
UNS N06625.
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
5. Ordering Information
mendations issued by the World Trade Organization Technical
5.1 It is the responsibility of the purchaser to specify all
Barriers to Trade (TBT) Committee.
requirements that are necessary for the safe and satisfactory
performance of material ordered under this specification.
2. Referenced Documents
Examples of such requirements include, but are not limited to,
3
2.1 ASTM Standards:
the following:
B775 Specification for General Requirements for Nickel and
5.1.1 Alloy name or UNS number,
Nickel Alloy Welded Pipe
5.1.2 ASTM designation,
B880 Specification for General Requirements for Chemical
5.1.3 Dimensions:
5.1.3.1 Pipe size,
5.1.3.2 Length (specific or random),
1
This specification is under the jurisdiction of ASTM Committee B02 on
5.1.4 Class (see Section 3),
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
5.1.5 Grade if UNS N06625 is specified. If neither grade of
B02.07 on Refined Nickel and Cobalt and Their Alloys.
Current edition approved Nov. 1, 2017. Published November 2017. Originally N06625 is specified, grade 1 will be supplied.
approved in 1982. Last previous edition approved in 2014 as B705 – 05 (2014).
5.1.6 Quantity (feet or number of pieces),
DOI: 10.1520/B0705-17.
5.1.7 Certification—State if certification is required,
2
New designation established in accordance with Practice E527 and SAE
J 1086, Practice for Numbering Metals and Alloys (UNS).
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from American Society of Mechanical Engineers (ASME), ASME
Standards volume information, refer to the standard’s Document Summary page on International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
the ASTM website. www.asme.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B705 − 17
TABLE 2 Mechanical Property Requirements
5.1.8 Samples for Product (Check) Analysis—State whether
samples for product (check) analysis should be furnished (7.2), Yield Elonga-
Tensile Strength tion in 2
and
Alloy Grade Strength 0.2 % Offset, in. or 50
5.1.9 Purchaser Inspection—If purchaser wishes to witness
min, psi (MPa) min, psi mm, min,
(MPa) %
tests
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.