ASTM D5150-92(2017)
(Test Method)Standard Test Method for Hiding Power of Architectural Paints Applied by Roller
Standard Test Method for Hiding Power of Architectural Paints Applied by Roller
SIGNIFICANCE AND USE
5.1 Laboratory hiding power measurements of architectural coatings generally employ blade-type applicators that lay down films of highly uniform thickness. But practical applicators, such as rollers, pads, and brushes, typically apply films that lack uniformity due to incomplete leveling, resulting in the practical hiding power of most paints being less than that measured on films applied with a drawdown blade. This test method simulates practical application procedures and conditions so as to provide an indication of the actual hiding performance obtainable when a paint is applied by an experienced worker. It is not intended to duplicate painting as done by the average consumer.
5.2 Since the rheological characteristics of a paint and its interaction with the applicator are influencing factors, rank order correlation between this test and one done by drawdown might not be obtained.
FIG. 1 Practical Opacity Chart in Accordance with Footnote 5 and Appendix X1
FIG. 2 Loading the Roller
SCOPE
1.1 This test method measures the ability of a paint to hide or obscure a surface to which it has been applied by a practical application procedure. This test method covers the use of a paint roller, but the concept is expected to work equally well when the application tool is a paint brush or paint pad.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D5150 − 92 (Reapproved 2017)
Standard Test Method for
1
Hiding Power of Architectural Paints Applied by Roller
This standard is issued under the fixed designation D5150; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Testing Paint, Varnish, Lacquer, and Related Materials
3
(Withdrawn 2016)
1.1 This test method measures the ability of a paint to hide
D3925 Practice for Sampling Liquid Paints and Related
or obscure a surface to which it has been applied by a practical
Pigmented Coatings
application procedure. This test method covers the use of a
E1347 Test Method for Color and Color-Difference Mea-
paint roller, but the concept is expected to work equally well
surement by Tristimulus Colorimetry
when the application tool is a paint brush or paint pad.
1.2 The values stated in inch-pound units are to be regarded
3. Terminology
as standard. The values given in parentheses are mathematical
3.1 Definitions:
conversions to SI units that are provided for information only
3.1.1 hiding power, n—theabilityofapaintorpaintmaterial
and are not considered standard.
as used to hide or obscure a surface to which it has been
1.3 This standard does not purport to address all of the
uniformly applied (see Terminology D16).
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
4. Summary of Test Method
priate safety and health practices and determine the applica-
4.1 The test paint is applied with a roller at a specified
bility of regulatory limitations prior to use.
spreading rate onto a test chart consisting of a series of light to
1.4 This international standard was developed in accor-
dark grey stripes. After drying, a second coat is applied in the
dance with internationally recognized principles on standard-
same manner over half of the chart. After the second coat has
ization established in the Decision on Principles for the
dried, both the single- and double-coated areas are evaluated
Development of International Standards, Guides and Recom-
for hiding as judged by the darkest stripe in each area that is
mendations issued by the World Trade Organization Technical
completely or almost completely obscured.
Barriers to Trade (TBT) Committee.
5. Significance and Use
2. Referenced Documents
5.1 Laboratory hiding power measurements of architectural
2
2.1 ASTM Standards:
coatingsgenerallyemployblade-typeapplicatorsthatlaydown
D16 TerminologyforPaint,RelatedCoatings,Materials,and
films of highly uniform thickness. But practical applicators,
Applications
such as rollers, pads, and brushes, typically apply films that
D1475 Test Method For Density of Liquid Coatings, Inks,
lack uniformity due to incomplete leveling, resulting in the
and Related Products
practical hiding power of most paints being less than that
D2244 Practice for Calculation of Color Tolerances and
measured on films applied with a drawdown blade. This test
Color Differences from Instrumentally Measured Color
method simulates practical application procedures and condi-
Coordinates
tions so as to provide an indication of the actual hiding
D3924 Specification for Environment for Conditioning and
performance obtainable when a paint is applied by an experi-
enced worker. It is not intended to duplicate painting as done
by the average consumer.
1
This test method is under the jurisdiction of ASTM Committee D01 on Paint
5.2 Since the rheological characteristics of a paint and its
and Related Coatings, Materials, andApplications and is the direct responsibility of
interaction with the applicator are influencing factors, rank
Subcommittee D01.42 on Architectural Coatings.
order correlation between this test and one done by drawdown
Current edition approved June 1, 2017. Published June 2017. Originally
might not be obtained.
approved in 1991. Last previous edition approved in 2013 as D5150 – 92 (2013).
DOI: 10.1520/D5150-92R17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.