EN 15804:2012/FprA1

Sustainability of construction works - Environmental product declarations - Core rules for the product category of construction products

This European standard provides core product category rules (PCR) for Type III environmental declarations for any construction product and construction service. NOTE The assessment of social and economic performances at product level is not covered by this standard. The core PCR: - defines the parameters to be declared and the way in which they are collated and reported, - describes which stages of a product’s life cycle are considered in the EPD and which processes are to be included in the life cycle stages, - defines rules for the development of scenarios,  -  includes the rules for calculating the Life Cycle Inventory and the Life Cycle Impact Assessment underlying the EPD, including the specification of the data quality to be applied, - includes the rules for reporting predetermined, environmental and health information, that is not covered by LCA for a product, construction process and construction service where necessary, - defines the conditions under which construction products can be compared based on the information provided by EPD. For the EPD of construction services the same rules and requirements apply as for the EPD of construction products.

Nachhaltigkeit von Bauwerken - Umweltproduktdeklarationen - Grundregeln für die Produktkategorie Bauprodukte

Contribution des ouvrages de construction au développement durable - Déclarations environnementales sur les produits - Règles régissant les catégories de produits de construction

Trajnostnost gradbenih objektov - Okoljske deklaracije na proizvodih - Osnovna pravila za kategorije proizvodov za gradbene proizvode - Dopolnilo A1

General Information

• Status: Not Published
• ICS: 91.010.99 - Other aspects
• Technical Committee: CEN/TC 350 - Sustainability of construction works
• Drafting Committee: CEN/TC 350/WG 3 - Products Level
• Current Stage: 5060 - Closure of Vote - Formal Approval
• Start Date: 09-Aug-2013
• Due Date: 09-Apr-2014
• Completion Date: 09-Aug-2013
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/350 - Development of Horizontal Standardised Methods for the assessment of the integrated Environmental performance of buildings
• Ref Project: SIST EN 15804:2012/kFprA1:2013 - Sustainability of construction works - Environmental product declarations - Core rules for the product category of construction products

Relations

• Merged Into: EN 15804:2012+A1:2013 - Sustainability of construction works - Environmental product declarations - Core rules for the product category of construction products
• Effective Date: 19-Jan-2023
• Amends: EN 15804:2012 - Sustainability of construction works - Environmental product declarations - Core rules for the product category of construction products
• Effective Date: 01-Aug-2012

Standards Content (Sample)

SLOVENSKI STANDARD
01-julij-2013
Trajnostnost gradbenih objektov - Okoljske deklaracije na proizvodih - Osnovna
pravila za kategorije proizvodov za gradbene proizvode - Dopolnilo A1
Sustainability of construction works - Environmental product declarations - Core rules for
the product category of construction products
Nachhaltigkeit von Bauwerken - Umweltproduktdeklarationen - Grundregeln für die
Produktkategorie Bauprodukte
Contribution des ouvrages de construction au développement durable - Déclarations
environnementales sur les produits - Règles régissant les catégories de produits de
construction
Ta slovenski standard je istoveten z: EN 15804:2012/FprA1
ICS:
13.020.99 Drugi standardi v zvezi z Other standards related to
varstvom okolja environmental protection
91.040.01 Stavbe na splošno Buildings in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 15804:2012
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
May 2013
ICS 91.010.99
English Version
Sustainability of construction works - Environmental product
declarations - Core rules for the product category of construction
products
Contribution des ouvrages de construction au Nachhaltigkeit von Bauwerken -
développement durable - Déclarations environnementales Umweltproduktdeklarationen - Grundregeln für die
sur les produits - Règles régissant les catégories de Produktkategorie Bauprodukte
produits de construction
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 350.
This draft amendment A1, if approved, will modify the European Standard EN 15804:2012. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15804:2012/FprA1:2013: E
worldwide for CEN national Members.

Contents Page
Foreword .3
1 Modification to 3.8 .4
2 Modification to NOTE of 5.1 .4
3 Modification to 6.3.2, first item in the list .4
4 Modification to 6.5 .4
5 Modification to 7.1, Table 2 .4
6 Modification to 7.3.1. second paragraph .5
7 Addition of the following Annex C .5

Foreword
This document (EN 15804:2012/FprA1:2013) has been prepared by Technical Committee CEN/TC 350
“Sustainability of construction works”, the secretariat of which is held by AFNOR.
This document is currently submitted to the Unique Acceptance Procedure.
1 Modification to 3.8
Replace "ISO 21930-1:2007" with "ISO 21930:2007".
2 Modification to NOTE of 5.1
Replace "See definition 3.4 and ISO14044:2006, clause 5.1" with "See definition 3.4 and
ISO 14044:2006, 5.3".
3 Modification to 6.3.2, first item in the list
Replace "dimensions to be specified” with “dimensions shall be specified".
4 Modification to 6.5
Replace the existing text of 6.5 with the following:
"The impact assessment is carried out for the following impact categories:
 global warming;
 ozone depletion;
 acidification of soil and water;
 eutrophication;
 photochemical ozone creation;
 depletion of abiotic resources (elements);
 depletion of abiotic resources (fossil).
The characterisation factors for GWP, ODP, AP, EP, POCP and ADP given in Annex C shall be used.
NOTE 1 The ‘accumulated exceedance’ method for AP and EP recommended by JRC is considered not to be ready for
standardization yet, because it needs a new regional set of characterisation factors, and because this method is not yet
common practice with the stakeholders nor available in databases. The method using the reserve base for ADP elements
recommended by JRC is not considered common practice.
If specific ADP fossil fuel values are known, these shall be used; any such use has to be stated.
Complementary and consistent factors may be used in order to achieve consistency between LCI data and
available characterisation factors.
NOTE 2 It is considered good practice to identify LCI data which has no calculated environmental impact within the
project report. This can help to identify the need for complementary and consistent characterisation factors for relevant LCI
flows."
5 Modification to 7.1, Table 2
Replace "Independent verification of the declaration” with “Independent verification of the declaration and
data”.
6 Modification to 7.3.1. second paragraph
Replace "defined in 7.2.2, 7.2.3 and 7.2.4" with "defined in 7.2.3, 7.2.4 and 7.2.5".
7 Addition of the following Annex C
"
Annex C
(normative)
Characterisation factors for GWP, ODP, AP, EP, POCP and ADP
The characterisation factors listed in the following tables are taken from CML –IA version 4.1, dated October
2012 (Institute of Environmental Sciences Faculty of Science University of Leiden, Netherlands) with the
permission of CML – © all rights reserved and identified as “baseline”.
Table A.1 — Characterisation factors concerning abiotic depletion (fossil fuels)
Characterisation
factor
Initial emission
Substance CAS No. Group Unit
or extraction
MJ
coal hard
(27.91 MJ/kg) coal hard fossil fuel resources kg 27,91
coal soft,
lignite (13.96
MJ/kg) coal soft fossil fuel resources kg 13,96
natural gas
8006-14-2
(38.84 MJ/m3) fossil fuel resources m3 38,84
oil crude
41,87
(41.87 MJ/kg) 8012-95-1 fossil fuel resources kg
NOTE Source of LCIA model: See Table C.8.

Table A.2 — Characterisation factors concerning abiotic depletion for non fossil resources
Characterisation
Substance CAS No. Group Initial emission or Unit
factor
extraction
kg antimony eq.
aluminium (Al) element resources kg 1,09E-09
7429-90-5
antimony (Sb) element resources kg 1,00E+00
7440-36-0
arsenic (As) element resources kg 2,97E-03
7440-38-2
barium (Ba) element resources kg 6,04E-06
7440-39-3
beryllium (Be) element resources kg 1,26E-05
7440-41-7
bismuth (Bi) element resources kg 4,11E-02
7440-69-9
boron (B) 7440-42-8 element resources kg 4,27E-03
bromine (Br) element resources kg 4,39E-03
7726-95-6
cadmium (Cd) element resources kg 1,57E-01
7440-43-9
chlorine (Cl) element resources kg 2,71E-05
7782-50-5
4,43E-04
chromium (Cr) 7440-47-3 element resources kg
cobalt (Co) element resources kg 1,57E-05
7440-48-4
copper (Cu) element resources kg 1,37E-03
7440-50-8
gallium (Ga) 7440-55-3 element resources kg 1,46E-07
germanium (Ge) element resources kg 6,52E-07
7440-56-4
gold (Au) element resources kg 5,20E+01
7440-57-5
indium (In) element resources kg 6,89E-03
7440-74-6
iodine (I2) 7553-56-2 element resources kg 2,50E-02
iron (Fe) element resources kg 5,24E-08
7439-89-6
kalium
(K;potassium) element resources kg 1,60E-08
7440-09-7
lead (Pb) element resources kg 6,34E-03
7439-92-1
lithium (Li) 7439-93-2 element resources kg 1,15E-05
2,02E-09
magnesium (Mg) 7439-95-4 element resources kg
manganese (Mn) element resources kg 2,54E-06
7439-96-5
9,22E-02
mercury (Hg) 7439-97-6 element resources kg
molybdenum (Mo) element resources kg 1,78E-02
7439-98-7
nickel (Ni) element resources kg 6,53E-05
7440-02-0
niobium (Nb) 7440-03-1 element resources kg 1,93E-05
5,71E-01
palladium (Pd) 7440-05-3 element resources kg
phosphorus (P) element resources kg 5,52E-06
7723-14-0
platinum (Pt) element resources kg 2,22E+00
7440-06-4
rhenium (Re) 7440-15-5 element resources kg 6,03E-01
selenium (Se) element resources kg 1,94E-01
7782-49-2
silicium (Si;
silicon) element resources kg 1,40E-11
7440-21-3
silver (Ag) element resources kg 1,18E+00
7440-22-4
Sodium (Na) element resources kg 5,50E-08
7440-23-5
7,07E-07
strontium (Sr) 7440-24-6 element resources kg
sulfur (S) element resources kg 1,93E-04
7704-34-9
tantalum (Ta) element resources kg 4,06E-05
7440-25-7
tellurium (Te) 13494-80-9 element resources kg 4,07E+01
thallium (Tl) element resources kg 2,43E-05
7440-28-0
tin (Sn) element resources kg 1,62E-02
7440-31-5
titanium (Ti) element resources kg 2,79E-08
7440-32-6
tungsten (W);
wolfram element resources kg 4,52E-03
7440-33-7
1,40E-03
uranium (U) 7440-61-1 element resources kg
vanadium (V) element resources kg 7,70E-07
7440-62-2
yttrium (Y) element resources kg 5,69E-07
7440-65-5
zinc (Zn) 7440-66-6 element resources kg 5,38E-04
Zirconium (Zr) element resources kg 5,44E-06
7440-67-7
NOTE Source of LCIA model: See Table C.8.

Table A.3 — Characterisation factors concerning acidification potential of soil and water
Substance CAS No. Group Initial emission or Unit Characterisation
factor
extraction
kg SO2 eq.
ammonia 7664-41-7 inorganic air kg 1,60E+00
5,00E-01
nitrogen dioxide 10102-44-0 inorganic air kg
nitrogen mono oxide 10102-43-9 inorganic air kg 7,60E-01
nitrogen oxides (as NO2) 11104-93-1 inorganic air kg 5,00E-01
sulphur dioxide 7446-09-5 inorganic air kg 1,20E+00
NOTE Source of LCIA model: See Table C.8.

Table A.4 — Characterisation factors concerning depletion potential of the stratospheric ozone layer
Substance CAS No. Group Initial Unit Characterisatio
n factor
emission
or
kg CFC-11 eq.
extraction
halogenated
1,1,1-trichloroethane 71-55-6 nonaromatic air kg 1,2E-01
halogenated
1,00E+00
CFC-11 75-69-4 nonaromatic air kg
halogenated
1,00E+00
CFC-113 76-13-1 nonaromatic air kg
halogenated
CFC-114 76-14-2 nonaromatic air kg 9,40E-01
halogenated
CFC-115 76-15-3 nonaromatic air kg 4,40E-01
halogenated
CFC-12 75-71-8 nonaromatic air kg 1,00E+00
halogenated
HALON (HALON 2401) 124-72-1 nonaromatic air kg 2,50E-01
halogenated
HBFC-1201 1511-62-2 nonaromatic air kg 1,40E+00
halogenated
HALON-1202 75-61-6 nonaromatic air kg 1,30E+00
HALON-1211 353-59-3 air kg 6,00E+00
halogenated
nonaromatic
halogenated
1,20E+01
HALON-1301 75-63-8 nonaromatic air kg
halogenated
1,40E-01
HBFC-2311 151-67-7 nonaromatic air kg
halogenated
HBFC-2401 (HALON) 124-72-1 (bis) nonaromatic air kg 2,50E-01
halogenated
HALON-2402 25497-30-7 nonaromatic air kg 6,00E+00
halogenated
HCFC-123 306-83-2 nonaromatic air kg 2,00E-02
2837-89-0 halogenated
HCFC-124 nonaromatic air kg 2,00E-02
1717-00-6 halogenated
HCFC-141b nonaromatic air kg 1,20E-01
halogenated
HCFC-142b 75-68-3 nonaromatic air kg 7,00E-02
halogenated
HCFC-22 75-45-6 nonaromatic air kg 5,00E-02
halogenated
HCFC-225ca 422-56-0 nonaromatic air kg 2,00E-02
halogenated
HCFC-225cb 507-55-1 nonaromatic air kg 3,00E-02
halogenated
Methyl Chloride 74-87-3 nonaromatic air kg 2,00E-02
methylbromide 74-83-9 pesticide air kg 3,8E-01
halogenated
Tetrachloromethane 56-23-5 nonaromatic air kg 7,3E-01
NOTE Source of LCIA model: See Table C.8.

Table A.5 — Characterisation factors concerning global warming potential
Characteris
Substance CAS No. Group Initial Unit
ation factor
emission
or
kg CO2 eq.
extraction
1,1,1-trichloroethane 71-55-6 halogenated nonaromatic air kg 1,5E+02
Carbon dioxide 124-38-9 inorganic air kg 1,0E+00
4,8E+03
CFC-11 75-69-4 halogenated nonaromatic air kg
CFC-113 76-13-1 halogenated nonaromatic air kg 6,1E+03
CFC-114 76-14-2 halogenated nonaromatic air kg 1,0E+04
CFC-115 76-15-3 halogenated nonaromatic air kg 7,4E+03
CFC-12 75-71-8 halogenated nonaromatic air kg 1,1E+04
CFC-13 75-72-9 halogenated nonaromatic air kg 1,4E+04
Dichloromethane 75-
...