EN ISO 22825:2006

Non-destructive testing of welds - Ultrasonic testing - Testing of welds in austenitic steels and nickel-based alloys (ISO 22825:2006)

ISO 22825:2006 specifies the approach to be followed when developing procedures for the ultrasonic testing of the following welds:
welds in austenitic stainless steels;
welds in nickel-based alloys;
welds in duplex steels;
dissimilar metal welds.
The purposes of the testing can be very different, e.g.:
for the assessment of quality level (manufacturing);
for the detection of specific indications induced in service.
Acceptance levels are not included in ISO 22825:2006, but can be applied in accordance with the scope of the testing.
The requirements of ISO 22825:2006 are applicable to both manual and mechanized testing.

Zerstörungsfreie Prüfung von Schweißverbindungen - Ultraschallprüfung - Prüfung von Schweißverbindungen in austenitischen Stählen und Nickellegierungen (ISO 22825:2006)

Diese Internationale Norm legt den Weg zur Entwicklung von Prüfanweisungen für die Ultraschallprüfung von folgenden Schweißverbindungen fest:
-   Schweißverbindungen in austenitischen Stählen;
-   Schweißverbindungen in Nickellegierungen;
-   Schweißverbindungen in Duplexstählen;
-   Schweißverbindungen zwischen unterschiedlichen Metallen.
Der Zweck der Prüfung kann sehr unterschiedlich sein, z. B.:
-   für die Bewertung der Güteklasse (Herstellung);
-   für den Nachweis spezifischer, durch den Gebrauch hervorgerufener Anzeigen.
Diese Internationale Norm enthält keine Zulässigkeitsgrenzen. Sie können entsprechend dem Anwendungs¬bereich der Prüfung, siehe Abschnitt 4, angewendet werden.
Die Anforderungen dieser Norm gelten sowohl für die manuelle als auch für die mechanisierte Prüfung.

Essais non destructifs des assemblages soudés - Contrôle par ultrasons - Contrôle des soudures en aciers austénitiques et en alliages à base nickel (ISO 22825:2006)

L'ISO 22825:2006 spécifie l'approche à suivre pour la mise au point des modes opératoires pour les contrôles par ultrasons des soudures suivantes:
soudures sur aciers inoxydables austénitiques;
soudures sur alliages à base nickel;
soudures sur aciers duplex;
soudures sur métaux dissemblables.
Les objectifs des contrôles peuvent être très différents (par exemple):
évaluation du niveau de qualité (fabrication);
détection d'indications spécifiques produites au cours du service.
Les niveaux d'acceptation ne sont pas inclus dans l'ISO 22825:2006, mais ils peuvent être appliqués selon le domaine d'application des contrôles.
Les exigences de l'ISO 22825:2006 sont applicables à la fois au contrôle manuel et au contrôle mécanisé.

Neporušitveno preskušanje zvarnih spojev iz avstenitnih jekel in nikljevih zlitin z ultrazvokom (ISO 22825:2006)

General Information

• Status: Withdrawn
• Publication Date: 30-Jun-2006
• Withdrawal Date: 14-May-2012
• ICS: 25.160.40 - Welded joints and welds
• Technical Committee: CEN/TC 121 - Welding
• Drafting Committee: CEN/TC 121/SC 5/WG 2 - Ultrasonic testing of welds
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 15-May-2012
• Completion Date: 15-May-2012
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN ISO 22825:2007 - Non-destructive testing of welds - Ultrasonic testing - Testing of welds in austenitic steels and nickel-based alloys (ISO 22825:2006)

Relations

• Replaced By: EN ISO 22825:2012 - Non-destructive testing of welds - Ultrasonic testing - Testing of welds in austenitic steels and nickel-based alloys (ISO 22825:2012)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 22825:2007
01-januar-2007
Neporušitveno preskušanje zvarnih spojev iz avstenitnih jekel in nikljevih zlitin z
ultrazvokom (ISO 22825:2006)
Non-destructive testing of welds - Ultrasonic testing - Testing of welds in austenitic steels
and nickel-based alloys (ISO 22825:2006)
Zerstörungsfreie Prüfung von Schweißverbindungen - Ultraschallprüfung - Prüfung von
Schweißverbindungen in austenitischen Stählen und Nickellegierungen (ISO
22825:2006)
Essais non destructifs des assemblages soudés - Contrôle par ultrasons - Contrôle des
soudures en aciers austénitiques et en alliages a base nickel (ISO 22825:2006)
Ta slovenski standard je istoveten z: EN ISO 22825:2006
ICS:
25.160.40 Varjeni spoji in vari Welded joints
SIST EN ISO 22825:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN ISO 22825
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2006
ICS 25.160.40

English Version
Non-destructive testing of welds - Ultrasonic testing - Testing of
welds in austenitic steels and nickel-based alloys (ISO
22825:2006)
Essais non destructifs des assemblages soudés - Contrôle Zerstörungsfreie Prüfung von Schweißverbindungen -
par ultrasons - Contrôle des soudures en aciers Ultraschallprüfung - Prüfung von Schweißverbindungen in
austénitiques et en alliages à base nickel (ISO 22825:2006) austenitischen Stählen und Nickellegierungen (ISO
22825:2006)
This European Standard was approved by CEN on 7 June 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22825:2006: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN ISO 22825:2006 (E)





Foreword


This document (EN ISO 22825:2006) has been prepared by Technical Committee CEN/TC 121
"Welding", the secretariat of which is held by DIN, in collaboration with Technical Committee
ISO/TC 44 "Welding and allied processes".

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by January 2007, and conflicting national
standards shall be withdrawn at the latest by January 2007.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


2

---------------------- Page: 3 ----------------------

INTERNATIONAL ISO
STANDARD 22825
First edition
2006-07-01


Non-destructive testing of welds —
Ultrasonic testing — Testing of welds in
austenitic steels and nickel-based alloys
Essais non destructifs des assemblages soudés — Contrôle par
ultrasons — Contrôle des soudures en aciers austénitiques et en
alliages à base nickel





Reference number
ISO 22825:2006(E)
©
ISO 2006

---------------------- Page: 4 ----------------------

ISO 22825:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF
...