District cooling pipes - Factory made flexible pipe systems - Part 3: Non bonded system with plastic service pipes; requirements and test methods

This document specifies requirements and test methods for factory made thermally insulated non bonded flexible pipe-in-pipe assemblies for directly buried district cooling distribution systems, comprising a service pipe from DN 15 to DN 200 and a casing of polyethylene. The pipe assembly may also include the following additional elements: measuring wires, spacers and diffusion barriers.
This document is intended to be used in conjunction with prEN 17414-1 ).
This document applies only to insulated pipe assemblies, for continuous operation with water at various temperatures (1 to 30) °C and a maximum operation pressure of 25 bar dependent on material specified.
The design is based on an expected service life with continuous operation of a minimum 50 years.
This document does not cover surveillance systems.
NOTE   For the transport of other liquids, for example potable water, additional requirements may be applicable.

Fernkälterohre - Werkmäßig gefertigte flexible Rohrsysteme - Teil 3: Nicht-Verbundrohrsysteme mit Mediumrohren aus Kunststoff - Anforderungen und Prüfungen

Dieses Dokument legt Anforderungen und Prüfverfahren für werkmäßig gefertigte und gedämmte flexible Nicht-Verbund-Rohr-in-Rohr-Systeme für direkt erdverlegte Fernkältenetzwerke, bestehend aus einem Mediumrohr und einem Polyethylenmantel, fest. Das Rohrsystem kann darüber hinaus die folgenden zusätzlichen Bauteile umfassen: Messdrähte, Abstandshalter und Diffusionsbarrieren.
Dieses Dokument ist für die Verwendung im Zusammenhang mit EN 17414 1 vorgesehen.
Dieses Dokument gilt nur für gedämmte Rohrsysteme, für den Dauerbetrieb mit Wasser bei verschiedenen Temperaturen 1 °C bis 30 °C und je nach Werkstoff einem Betriebsdruck von höchstens 25 bar.
Die Auslegung basiert auf einer erwarteten Lebensdauer von mindestens 50 Jahren bei Dauerbetrieb.
Dieses Dokument gilt nicht für Überwachungssysteme.
Zusammen mit den anderen Teilen von EN 17414 gilt dieses Dokument für Rohre, Formstücke, ihre Verbindungen untereinander sowie mit Rohrleitungsteilen, deren Werkstoffe nicht aus Kunststoff bestehen und die für Fernkälteinstallationen vorgesehen sind.
ANMERKUNG   Für den Transport anderer Flüssigkeiten, z. B. Trinkwasser, könnten zusätzliche Anforderungen gelten.

Réseaux d’eau glacée - Systèmes de tuyaux flexibles manufacturés - Partie 3 : Système non bloqué avec tube de service en plastique - prescriptions et méthodes d'essai

Le présent document spécifie les exigences et méthodes d’essai pour les tuyaux non bloqués à double enveloppe flexibles isolés thermiquement manufacturés pour réseaux de distribution d’eau glacée enterrés directement, comprenant un tube de service et un tube de protection en polyéthylène. Le tuyau préisolé peut également comprendre les éléments supplémentaires suivants : les câbles de mesure, les entretoises et les barrières anti diffusion.
Le présent document est destiné à être utilisé conjointement avec l’EN 17414-1.
Le présent document s’applique uniquement aux tuyaux préisolés conçus pour un fonctionnement continu avec de l’eau à diverses températures (allant de 1 °C à 30 °C) et à une pression de service maximale de 25 bar dépendant du matériau spécifié.
La conception est fondée sur une durée utile prévue en fonctionnement continu d’au moins 50 ans.
Le présent document ne couvre pas les systèmes de surveillance.
En conjonction avec les autres parties de l’EN 17414, le présent document est applicable aux tubes, aux raccords, aux joints et aux joints avec composants non constitués de matériaux plastiques destinés à être utilisés dans les installations de refroidissement urbain.
NOTE   Pour le transport d’autres liquides, par exemple de l’eau potable, des prescriptions supplémentaires peuvent s’appliquer.

Cevi za daljinsko hlajenje - Tovarniško izdelani gibki cevni sistemi - 3. del: Nevezani sistem z delovnimi cevmi iz polimernih materialov - Zahteve in preskusne metode

General Information

Status
Published
Publication Date
28-Jul-2020
Withdrawal Date
30-Jan-2021
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
29-Jul-2020
Due Date
27-Aug-2021
Completion Date
29-Jul-2020

Buy Standard

Standard
EN 17414-3:2020
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 17414-3:2019
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 17414-3:2020
01-oktober-2020
Cevi za daljinsko hlajenje - Tovarniško izdelani gibki cevni sistemi - 3. del:
Nevezani sistem z delovnimi cevmi iz polimernih materialov - Zahteve in
preskusne metode
District cooling pipes - Factory made flexible pipe systems - Part 3: Non bonded system
with plastic service pipes - Requirements and test methods
Fernkühlungsrohre - Werkmäßig gedämmte flexible Rohrsysteme - Teil 3: Nicht-Verbund-
Rohrsysteme mit Mediumrohren aus Kunststoff - Anforderungen und Prüfungen
Réseaux d’eau glacée - Systèmes de tuyaux flexibles manufacturés - Partie 3 : Système
non bloqué avec tube de service en plastique - Prescriptions et méthodes d'essai
Ta slovenski standard je istoveten z: EN 17414-3:2020
ICS:
23.040.99 Drugi sestavni deli za Other pipeline components
cevovode
SIST EN 17414-3:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 17414-3:2020

---------------------- Page: 2 ----------------------
SIST EN 17414-3:2020


EN 17414-3
EUROPEAN STANDARD

NORME EUROPÉENNE

July 2020
EUROPÄISCHE NORM
ICS 23.040.99
English Version

District cooling pipes - Factory made flexible pipe systems
- Part 3: Non bonded system with plastic service pipes;
requirements and test methods
Réseaux d'eau glacée - Systèmes de tuyaux flexibles Fernkälterohre - Werkmäßig gefertigte flexible
manufacturés - Partie 3 : Système non bloqué avec tube Rohrsysteme - Teil 3: Nicht-Verbundrohrsysteme mit
de service en plastique - prescriptions et méthodes Mediumrohren aus Kunststoff - Anforderungen und
d'essai Prüfungen
This European Standard was approved by CEN on 22 June 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17414-3:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 17414-3:2020
EN 17414-3:2020 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Classification. 7
4.1 Operating temperatures and service life . 7
4.2 Design pressures . 7
5 Requirements . 8
5.1 General requirements . 8
5.2 Service pipes, fittings and the
...

SLOVENSKI STANDARD
oSIST prEN 17414-3:2019
01-november-2019
Cevi za daljinsko hlajenje - Tovarniško izdelani sistemi gibkih cevi - 3. del:
Nespojeni sistem s plastičnimi delovnimi cevmi - Zahteve in preskusne metode
District cooling pipes - Factory made flexible pipe systems - Part 3: Non bonded system
with plastic service pipes - Requirements and test methods
Fernkühlungsrohre - Werkmäßig gedämmte flexible Rohrsysteme - Teil 3: Nicht-Verbund-
Rohrsysteme mit Mediumrohren aus Kunststoff - Anforderungen und Prüfungen
Réseaux d’eau glacée - Systèmes de tuyaux flexibles manufacturés - Partie 3 : Système
non bloqué avec tube de service en plastique - Prescriptions et méthodes d'essai
Ta slovenski standard je istoveten z: prEN 17414-3
ICS:
23.040.99 Drugi sestavni deli za Other pipeline components
cevovode
oSIST prEN 17414-3:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 17414-3:2019

---------------------- Page: 2 ----------------------
oSIST prEN 17414-3:2019


DRAFT
EUROPEAN STANDARD
prEN 17414-3
NORME EUROPÉENNE

EUROPÄISCHE NORM

July 2019
ICS 23.040.99
English Version

District cooling pipes - Factory made flexible pipe systems
- Part 3: Non bonded system with plastic service pipes -
Requirements and test methods
Réseaux d'eau glacée - Systèmes de tuyaux flexibles Fernkühlungsrohre - Werkmäßig gedämmte flexible
manufacturés - Partie 3 : Système non bloqué avec tube Rohrsysteme - Teil 3: Nicht-Verbund-Rohrsysteme mit
de service en plastique - Prescriptions et méthodes Mediumrohren aus Kunststoff - Anforderungen und
d'essai Prüfungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 107.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 17414-3:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 17414-3:2019
prEN 17414-3:2019 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Classification. 6
4.1 Operating temperatures and service life . 6
4.2 Operating pressures . 6
5 Requirements .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.