EN ISO 15876-5:2017

Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system (ISO 15876-5:2017)

ISO 15876-5:2017 specifies the characteristics of the fitness for purpose of polybutene-1 (PB-1) piping systems, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption, (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application (see ISO 15876‑1).
The designation polybutene is used together with the abbreviation PB throughout this document.
ISO 15876-5:2017 covers a range of service conditions (application classes) and design pressure classes. For values of TD, Tmax and Tmal in excess of those in ISO 15876‑1:2016, Table 1, this document does not apply.
NOTE          It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with the other parts of ISO 15876, it is applicable to PB pipes, fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations.

Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polybuten (PB) - Teil 5: Gebrauchstauglichkeit des Systems (ISO 15876-5:2017)

Dieses Dokument legt Anforderungen an die Gebrauchstauglichkeit von Rohrleitungssystemen aus Polybuten-1 (PB-1) fest, die für die Verwendung in der Warm- und Kaltwasserinstallation innerhalb von Gebäuden für den Transport von Trink- oder Brauchwasser (Hausinstallation) sowie für Heizungsanlagen bei den zulässigen Betriebsdrücken und Temperaturen entsprechend der Anwendungsklasse (siehe ISO 15876-1) vorgesehen sind.
In diesem Dokument wird durchgehend die Bezeichnung Polybuten zusammen mit der Abkürzung PB verwendet.
Dieses Dokument deckt einen Bereich von Betriebsbedingungen (Anwendungsklassen) sowie zulässige Betriebsdrücke ab. Dieses Dokument gilt nicht für Werte für TD, Tmax und Tmal oberhalb der in ISO 15876-1:2016N1), Tabelle 1, angegebenen Werte.
ANMERKUNG   Der Anwender bzw. Auftraggeber ist unter Berücksichtigung der eigenen besonderen Anforderungen sowie der geltenden nationalen Festlegungen und Verlegepraktiken für die entsprechende Auswahl anhand dieser Kriterien verantwortlich.
Es legt auch die Prüfparameter für die Prüfverfahren fest, auf die in diesem Dokument verwiesen wird.
Zusammen mit den übrigen Teilen von ISO 15876 gilt dieses Dokument für Rohre und Formstücke aus PB, deren Verbindungen untereinander sowie mit Rohrleitungsteilen aus anderen Kunststoffen oder Nichtkunststoffen, die für die Warm- und Kaltwasserinstallation vorgesehen sind.

Systèmes de canalisations en plastique pour les installations d'eau chaude et froide - Polybutène (PB) - Partie 5: Aptitude à l'emploi du système (ISO 15876-5:2017)

ISO 15876-5:2017 spécifie les caractéristiques d'aptitude à l'emploi des systèmes de canalisations en polybutène-1 (PB-1), conçus pour être utilisés dans des installations d'eau chaude et froide à l'intérieur des bâtiments, pour le transport de l'eau destinée ou non à la consommation humaine (systèmes domestiques), et dans des installations de chauffage, à des pressions et des températures de service correspondant à leur classe d'application (voir l'ISO 15876‑1).
La désignation polybutène est utilisée conjointement avec l'abréviation PB dans l'ensemble du présent document.
ISO 15876-5:2017 couvre une gamme de conditions de service (classes d'application) et de classes de pressions de service. Pour les valeurs TD, Tmax et Tmal dépassant celles de l'ISO 15876‑1, Tableau 1, le présent document ne s'applique pas.
NOTE          Il est de la responsabilité de l'acheteur ou du prescripteur de sélectionner convenablement ces aspects, en tenant compte des exigences particulières et des éventuelles règles nationales et pratiques ou codes de pose appropriés.
Il spécifie également les paramètres d'essai pour les méthodes d'essai auxquelles il est fait référence dans le présent document.
Avec les autres parties de l'ISO 15876, il s'applique aux tubes et aux raccords en PB, à leurs assemblages et aux assemblages avec des composants fabriqués dans d'autres matériaux, plastiques ou non plastiques, destinés à des installations d'eau chaude et froide.

Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo - Polibuten (PB) - 5. del: Ustreznost sistema namenu (ISO 15876-5:2017)

Ta del standarda EN ISO 15876 določa značilnosti ustreznosti namenu za cevne sisteme iz polibutena-1 (PB-1), ki se uporabljajo za napeljave z vročo in hladno vodo za prenos pitne in nepitne vode v stavbah (gospodinjski sistemi), ter za sisteme ogrevanja glede na predvidene tlake in temperature v skladu z razredom uporabe (glej preglednico 1 standarda EN ISO 15876-1:2003). Zaradi poenostavitve se poimenovanje polibuten v tem dokumentu uporablja skupaj s kratico PB. Ta standard zajema različne pogoje uporabe (razrede uporabe) in razrede predvidenih tlakov. Ta standard se ne uporablja za vrednosti TD, Tmaks in Tmal, ki presegajo vrednosti iz standarda EN ISO 15876-1. OPOMBA: Za ustrezno izbiro teh vidikov je odgovoren kupec ali projektant, pri čemer mora upoštevati posebne zahteve ter vse pomembne nacionalne predpise in prakse ali kodekse vgradnje. Določa tudi preskusne parametre za preskusne metode iz tega standarda. ISO 15876 je referenčni standard za izdelke. Uporablja se za cevi, fitinge, njihove spoje ter tudi za spoje s sestavnimi deli iz drugih polimernih in nepolimernih materialov, namenjene uporabi v napeljavah z vročo in hladno vodo. Ta del standarda ISO 15876 je namenjen uporabi skupaj z vsemi ostalimi deli standarda ISO 15876.

General Information

• Status: Published
• Publication Date: 07-Feb-2017
• Withdrawal Date: 30-Aug-2017
• ICS: 23.040.01 - Pipeline components and pipelines in general
• ICS: 23.040.20 - Plastics pipes
• ICS: 91.140.60 - Water supply systems
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155/WG 16 - Systems for hot and cold water applications
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 08-Feb-2017
• Due Date: 14-Feb-2017
• Completion Date: 08-Feb-2017
• Directive: 89/106/EEC - Construction products
• Ref Project: SIST EN ISO 15876-5:2017 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system (ISO 15876-5:2017)

Relations

• Replaces: EN ISO 15876-5:2003 - Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 5: Fitness for purpose of the system (ISO 15876-5:2003)
• Effective Date: 15-Feb-2017
• Amended By: EN ISO 15876-5:2017/A1:2020 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system - Amendment 1 (ISO 15876-5:2017/Amd 1:2020)
• Effective Date: 20-Nov-2019

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2017
1DGRPHãþD
SIST EN ISO 15876-5:2004
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DQDSHOMDYH]YURþRLQKODGQRYRGR
3ROLEXWHQ3%GHO8VWUH]QRVWVLVWHPDQDPHQX,62
Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5:
Fitness for purpose of the system (ISO 15876-5:2017)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polybuten
(PB) - Teil 5: Gebrauchstauglichkeit des Systems (ISO 15876-5:2017)
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide -
Polybutène (PB) - Partie 5 : Apitude à l'emploi du système (ISO 15876-5:2017)
Ta slovenski standard je istoveten z: EN ISO 15876-5:2017
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.60 Sistemi za oskrbo z vodo Water supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 15876-5
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2017
EUROPÄISCHE NORM
ICS 23.040.20; 91.140.60 Supersedes EN ISO 15876-5:2003
English Version
Plastics piping systems for hot and cold water installations
- Polybutene (PB) - Part 5: Fitness for purpose of the
system (ISO 15876-5:2017)
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für die Warm- und
installations d'eau chaude et froide - Polybutène (PB) - Kaltwasserinstallation - Polybuten (PB) - Teil 5:
Partie 5: Aptitude à l'emploi du système (ISO 15876- Gebrauchstauglichkeit des Systems (ISO 15876-
5:2017) 5:2017)
This European Standard was approved by CEN on 24 December 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15876-5:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 15876-5:2017) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee
CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2017, and conflicting national standards shall
be withdrawn at the latest by August 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 15876-5:2003.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 15876-5:2017 has been approved by CEN as EN ISO 15876-5:2017 without any
modification.
INTERNATIONAL ISO
STANDARD 15876-5
Second edition
2017-01
Plastics piping systems for hot
and cold water installations —
Polybutene (PB) —
Part 5:
Fitness for purpose of the system
Systèmes de canalisations en plastique pour les installations d’eau
chaude et froide — Polybutène (PB) —
Partie 5: Aptitude à l’emploi du système
Reference number
ISO 15876-5:2017(E)
©
ISO 2017
ISO 15876-5:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – All rights reserved

ISO 15876-5:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions, symbols and abbreviated terms . 2
4 Fitness for purpose of the joints and the piping system . 2
4.1 General . 2
4.2 Internal pressure test . 2
4.3 Bending test . 4
4.4 Pull-out test . 5
4.5 Thermal cycling test . 5
4.6 Pressure cycling test . 6
4.7 Leaktightness under vacuum . 7
Bibliography . 8
ISO 15876-5:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www . i so .org/ iso/ foreword .html.
ISO 15876-5 was prepared by the European Committee Standardization (CEN) Technical Committee
CEN/TC 155, Plastics pipings systems and ducting systems, in collaboration with ISO Technical Committee
ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes
and fittings for water supplies, in accordance with the Agreement on technical cooperation between ISO
and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 15876-5:2003), which has been
technically revised with the following changes:
— introduction of polybutene random copolymer (PB-R) and renaming existing polybutene (PB) into
polybutene homopolymer (PB-H);
— revision of specifications for conditioning of samples.
A list of all parts in the ISO 15876 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved

ISO 15876-5:2017(E)
Introduction
The System Standard ISO 15876, of which this document is Part 5, specifies the requirements for a
piping system when made from polybutene (PB). The piping system is intended to be used for hot and
cold water installations.
In respect of potential adverse effects on the quality of water intended for human consumption, caused
by the product covered by ISO 15876 (all parts):
— ISO 15876 (all parts) provides no information as to whether the product may be used without
restriction in any of the Member States of the EU or EFTA;
— it should be noted that, while awaiting the adoption of verifiable European criteria, existing national
regulations concerning the use and/or the characteristics of this product remain in force.
Requirements and test methods for material and components of the piping system are specified
in ISO 15876-1, ISO 15876-2 and ISO 15876-3. ISO/TS 15876-7 gives guidance for the assessment of
conformity.
This document specifies the characteristics of fitness for purpose of the piping systems.
At the date of publication of this standard, System Standards for piping systems of other plastics
materials used for the same application include ISO 15874, ISO 15875, ISO 15876, ISO 15877, ISO 21003
and ISO 22391.
INTERNATIONAL STANDARD ISO 15876-5:2017(E)
Plastics piping systems for hot and cold water
installations — Polybutene (PB) —
Part 5:
Fitness for purpose of the system
1 Scope
This document specifies the characteristics of the fitness for purpose of polybutene-1 (PB-1) piping
systems, intended to be used for hot and cold water installations within buildings for the conveyance of
water, whether or not intended for human consumption, (domestic systems) and for heating systems,
under design pressures and temperatures according to the class of application (see ISO 15876-1).
The designation polybutene is used together with the abbreviation PB throughout this document.
This document covers a range of service conditions (application classes) and design pressure classes. For
values of T , T and T in excess of those in ISO 15876-1:2016, Table 1, this document does not apply.
D max mal
NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from th
...