EN 4534-2:2009

Aerospace series - Bushes, plain in aluminium alloy with self-lubricating liner, elevated load - Part 2: Dimensions and loads - Inch series

This standard specifies the characteristics of plain bushes in aluminium alloy with self-lubricating liner,
elevated load for aerospace applications.
The bushes are intended for use in fixed or moving parts of the aircraft structure and control mechanisms.
They shall be used in the temperature range - 55 °C to 121 °C.

Luft- und Raumfahrt - Buchsen aus Aluminiumlegierung, mit selbstschmierender Beschichtung, erhöhte Belastung - Teil 2: Maße und Belastungen - Inch-Reihe

Die vorliegende Norm legt die Eigenschaften von Buchsen aus Aluminiumlegierung mit selbstschmierender Beschichtung, erhöhter Belastung, für die Anwendung in der Luft- und Raumfahrt fest.
Die Buchsen sind für den Einsatz in starren oder beweglichen Teilen der Luftfahrzeugstruktur und der Betätigungsvorrichtungen vorgesehen.
Sie sind für den Einsatz im Temperaturbereich von - 55 °C bis 121 °C bestimmt.

Série aérospatiale - Bagues en alliage d'aluminium à garniture autolubrifiante, charge élevée - Partie 2 : Dimensions et charges - Série en inches

Aeronavtika - Drsne puše iz aluminijeve zlitine s samomazalno oblogo, serija za večje obremenitve - 2. del: Mere in nosilnosti - Colski tip

General Information

• Status: Withdrawn
• Publication Date: 09-Jun-2009
• Withdrawal Date: 06-Sep-2016
• ICS: 49.035 - Components for aerospace construction
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 3 - Mechanical
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 30-Jun-2017
• Ref Project: SIST EN 4534-2:2009 - Aerospace series - Bushes, plain in aluminium alloy with self-lubricating liner, elevated load - Part 2: Dimensions and loads - Inch series

Relations

• Replaced By: EN 4534-2:2016 - Aerospace series - Bushes, plain in aluminium alloy with self-lubricating liner, elevated load - Part 2: Dimensions and loads - Inch series
• Effective Date: 14-Sep-2016

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Buchsen aus Aluminiumlegierung, mit selbstschmierender Beschichtung, erhöhte Belastung - Teil 2: Maße und Belastungen - Inch ReiheSérie aérospatiale - Bagues en alliage d'aluminium à garniture autolubrifiante, charge élevée - Partie 2 : Dimensions et charges - Série en inchesAerospace series - Bushes, plain in aluminium alloy with self-lubricating liner, elevated load - Part 2: Dimensions and loads - Inch series49.035Sestavni deli za letalsko in vesoljsko gradnjoComponents for aerospace construction49.025.20AluminijAluminiumICS:Ta slovenski standard je istoveten z:EN 4534-2:2009SIST EN 4534-2:2009en01-september-2009SIST EN 4534-2:2009SLOVENSKI
STANDARD



SIST EN 4534-2:2009



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 4534-2June 2009ICS 49.035 English VersionAerospace series - Bushes, plain in aluminium alloy with self-lubricating liner, elevated load - Part 2: Dimensions and loads -Inch seriesSérie aérospatiale - Bagues en alliage d'aluminium àgarniture autolubrifiante, charge élevée - Partie 2 :Dimensions et charges - Série en inchesLuft- und Raumfahrt - Buchsen aus Aluminiumlegierung,mit selbstschmierender Beschichtung, erhöhte Belastung -Teil 2: Maße und Belastungen - Inch ReiheThis European Standard was approved by CEN on 24 April 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 4534-2:2009: ESIST EN 4534-2:2009



EN 4534-2:2009 (E) 2 Contents Page Foreword .3 1 Scope .4 2 Normative references .4 3 Terms and definitions .4 4 Requirements .4 4.1 Configuration, dimensions, tolerances and mass .4 4.2 Surface roughness .4 4.3 Materials .5 4.4 Surface treatment .5 5 Designation . 12 6 Marking . 13 7 Technical specification . 13 8 Design recommendation . 13
SIST EN 4534-2:2009



EN 4534-2:2009 (E) 3 Foreword This document (EN 4534-2:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). This European Standard shall be given the status of a national standard, either by publication
...