EN ISO 21178:2006
(Main)Light conveyor belts - Determination of electrical resistances (ISO 21178:2005)
Light conveyor belts - Determination of electrical resistances (ISO 21178:2005)
ISO 21178:2005 specifies test methods for determining the electrical resistances of light conveyor belts according to ISO 21183-1. The resistances are surface resistance, volume resistance perpendicular to the belt plane, and longitudinal and transverse volume resistance parallel to the belt plane. ISO 21178:2005 also specifies two test methods for determining the surface resistivity and the volume resistivity.
Leichte Födergurte - Bestimmung der elektrischen Widerstände (ISO 21178:2005)
Diese Europäische Norm legt Prüfverfahren zur Bestim¬mung der elektrischen Widerstände leichter Fördergurte fest, wie sie in ISO 21183-1 beschrieben sind. Die Widerstände sind der Oberflächenwiderstand, der Durchgangswiderstand senkrecht zur Gurtoberfläche und der Durchgangswider¬stand in Längs- und Querrichtung parallel zur Gurtober¬fläche. Des Weiteren sind in dieser Norm zwei Verfahren zur Ermittlung des spezifischen Oberflächenwiderstan¬des und des spezifischen Durchgangswiderstandes ent¬halten.
Courroies transporteuses légères - Détermination des résistances électriques (ISO 21178:2005)
L'ISO 21178:2005 spécifie des méthodes d'essai permettant de déterminer les résistances électriques des courroies transporteuses légères décrites dans l'ISO 21183-1. Ces résistances sont la résistance surfacique, la résistance volumique perpendiculaire au plan de la courroie et la résistance volumique dans les sens longitudinal et transversal, parallèlement au plan de la courroie. L'ISO 21178:2005 spécifie également deux méthodes d'essai pour déterminer la résistivité surfacique et la résistivité volumique.
Naprave za kontinuirni transport – Lahki trakovi tračnih transporterjev – Preskusna metoda za določanje električnih upornosti (ISO 21178:2005)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Light conveyor belts - Determination of electrical resistances (ISO 21178:2005)Courroies transporteuses légeres - Détermination des résistances électriques (ISO 21178:2005)Leichte Födergurte - Bestimmung der elektrischen Widerstände (ISO 21178:2005)Ta slovenski standard je istoveten z:EN ISO 21178:2006SIST EN
ISO 21178:2007en53.040.20Deli za transporterjeComponents for conveyorsICS:SLOVENSKI
STANDARDSIST EN
ISO 21178:200701-april-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 21178November 2006ICS 53.040.10Supersedes EN 1637:1999
English VersionLight conveyor belts - Determination of electrical resistances(ISO 21178:2005)Courroies transporteuses légères - Détermination desrésistances électriques (ISO 21178:2005)Leichte Födergurte - Bestimmung der elektrischenWiderstände (ISO 21178:2005)This European Standard was approved by CEN on 21 October 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 21178:2006: E
Endorsement notice The text of ISO 21178:2005 has been approved by CEN as EN ISO 21178:2006 without any modifications.
Reference numberISO 21178:2005(E)© ISO 2005
INTERNATIONAL STANDARD ISO21178First edition2005-11-01Light conveyor belts — Determination of electrical resistances Courroies transporteuses légères — Détermination des résistances électriques
ISO 21178:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii
ISO 21178:2005(E) © ISO 2005 – All rights reserved
iiiContents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Symbols.1 4 Electrical surface resistances.2 4.1 Method A: measurement of surface resistance ROA omni-directionally.2 4.2 Method B: measurement of surface resistance ROB in longitudinal and transverse direction.5 5 Electrical surface resistivity ρs.7 5.1 General.7 5.2 Principle.7 5.3 Apparatus.7 5.4 Preparation and preservation of test pieces prior to testing.9 5.5 Procedure.9 5.6 Expression of results.9 5.7 Test report.10 6 Electrical volume resistances.10 6.1 Volume resistance RD perpendicular to plane of belt.10 6.2 Volume resistance RDi in longitudinal and transverse direction parallel to plane of belt.14 7 Electrical volume resistivity ρD.17 7.1 Procedure.17 7.2 Expression of results.17 7.3 Test report.17 Annex A (informative)
Comparative values for electrical resistances.18
ISO 21178:2005(E) iv
INTERNATIONAL STANDARD ISO 21178:2005(E) © ISO 2005 – All rights reserved
1Light conveyor belts — Determination of electrical resistances 1 Scope This International Standard specifies test methods for determining the electrical resistances of light conveyor belts according to ISO 21183-1. The resistances are surface resistance, volume resistance perpendicular to the belt plane, and longitudinal and transverse volume resistance parallel to the belt plane. This International Standard also specifies two test methods for determining the surface resistivity and the volume resistivity. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 18573:2003, Conveyor belts — Test atmospheres and conditioning periods ISO 21183-1, Light conveyor belts — Part 1: Principal characteristics and applications 3 Symbols Symbol Quantity Unit ROA Electrical surface resistance, method A Ω ROB Electrical surface resistance, method B Ω ROG Electrical surface resistance for the determination of ρs Ω RD Electrical volume resistance perpendicular to the plane of the belt Ω RDi Electrical volume resistance in longitudinal and transverse direction parallel
to the plane of the belt Ω ρs1) Electrical surface resistivity Ω ρD Electrical volume resistivity Ω⋅cm d1/2/3 Diameter of electrode cm dm Middle of the gap diameter cm g Width of the gap cm A Surface of the electrode cm2 h Thickness of test piece cm
1) The SI unit of surface resistivity is the ohm (Ω). In practice this is sometimes referred to as “ohm/square” or “Ω/sq” or “Ω/†”. The size of the square is immaterial.
ISO 21178:2005(E) 2
ISO 21178:2005(E) © ISO 2005 – All rights reserved
34.1.4.5 Conditioning Before testing, condition the test pieces in accordance with ISO 18573:2003, Atmosphere B, for 24 h, except that, if the light conveyor belt consists of materials with a high absorption of moisture, e.g. cotton or polyamide, condition the test piece for 48 h. 4.1.4.6 Preparation Prepare the test pieces in the following manner after conditioning according to 4.1.4.5. To ensure good contact between electrodes and test piece a contact agent shall be used. The electrical surface resistivity of the contact agent shall not be higher than 104 Ω. For checking this value, use the same electrode arrangement as described in Clause 5. NOTE A jelly having the following composition is suitable: anhydrous polyethylene glycol of molecular mass 600 800 parts by mass; water 200 parts by mass; potassium chloride 10 parts by mass; soft soap (pharmaceutical quality) 1 part by mass. If the surface of the test piece is flat, paint the contact agent onto the bottom surface of the cleaned electrodes. If the surface of the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.