EN ISO 8496:2013

Metallic materials - Tube - Ring tensile test (ISO 8496:2013)

ISO 8496:2013 specifies a method for a ring tensile test of tubes to reveal surface and internal defects by subjecting the test piece to strain until fracture occurs. This test may also be used to assess the ductility of tubes.
The ring tensile test is applicable to tubes having an outside diameter exceeding 150 mm and a wall thickness no greater than 40 mm. The inside diameter shall be greater than 100 mm.

Metallische Werkstoffe - Rohr - Ringzugversuch (ISO 8496:2013)

Diese Internationale Norm legt ein Verfahren für einen Ringzugversuch für Rohre fest, der der Feststellung von Oberflächen- und Innenfehlern durch Beanspruchung eines Probekörpers bis zum Bruch dient. Diese Prüfung darf auch zur Bewertung der Dehnbarkeit von Rohren angewendet werden.
Der Ringzugversuch gilt für Rohre mit einem Außendurchmesser von mehr als 150 mm und einer Wanddicke von höchstens 40 mm. Der Innendurchmesser muss größer als 100 mm sein.

Matériaux métalliques - Tubes - Essai de traction sur anneaux (ISO 8496:2013)

L'ISO 8496:2013 spécifie une méthode d'essai de traction sur anneaux de tubes, visant à révéler les défauts superficiels et internes, en soumettant l'éprouvette à une déformation jusqu'à rupture. L'essai peut également être utilisé pour évaluer la ductilité des tubes.
L'essai de traction sur anneaux s'applique aux tubes ayant un diamètre extérieur supérieur à 150 mm et une épaisseur de paroi ne dépassant pas 40 mm. Le diamètre intérieur doit être supérieur à 100 mm.

Kovinski materiali - Cev - Natezni preskus obroča (ISO 8496:2013)

Ta mednarodni standard določa metodo za natezni preskus obroča cevi, s čimer se odkrije površinske in notranje hibe tako, da se preskušanca nateza, dokler se ta ne zlomi. Ta preskus se lahko uporabi tudi za ocenjevanje duktilnosti cevi. Natezni preskus obroča cevi se uporablja za cevi z zunanjim premerom, večjim od 150 mm, in debelino stene, manjšo od 40 mm. Notranji premer je nujno večji od 100 mm.

General Information

• Status: Published
• Publication Date: 19-Nov-2013
• Withdrawal Date: 30-May-2014
• ICS: 77.040.10 - Mechanical testing of metals
• Technical Committee: ECISS/TC 110 - Steel tubes, and iron and steel fittings
• Drafting Committee: ECISS/TC 110 - Steel tubes, and iron and steel fittings
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 20-Nov-2013
• Completion Date: 20-Nov-2013
• Ref Project: SIST EN ISO 8496:2014 - Metallic materials - Tube - Ring tensile test (ISO 8496:2013)

Relations

• Replaces: EN ISO 8496:2004 - Metallic materials - Tube - Ring tensile test (ISO 8496:1998)
• Effective Date: 17-Apr-2013

Standards Content (Sample)

SLOVENSKI STANDARD
01-julij-2014
1DGRPHãþD
SIST EN ISO 8496:2004
.RYLQVNLPDWHULDOL&HY1DWH]QLSUHVNXVREURþD,62
Metallic materials - Tube - Ring tensile test (ISO 8496:2013)
Metallische Werkstoffe - Rohr - Ringzugversuch (ISO 8496:2013)
Matériaux métalliques - Tubes - Essai de traction sur anneaux (ISO 8496:2013)
Ta slovenski standard je istoveten z: EN ISO 8496:2013
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 8496
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2013
ICS 77.040.10 Supersedes EN ISO 8496:2004
English Version
Metallic materials - Tube - Ring tensile test (ISO 8496:2013)
Matériaux métalliques - Tubes - Essai de traction sur Metallische Werkstoffe - Rohr - Ringzugversuch (ISO
anneaux (ISO 8496:2013) 8496:2013)
This European Standard was approved by CEN on 28 October 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8496:2013 E
worldwide for CEN national Members.

Contents Page
Foreword .3
Foreword
This document (EN ISO 8496:2013) has been prepared by Technical Committee ISO/TC 164 "Mechanical
testing of metals" in collaboration with Technical Committee ECISS/TC 110 “Steel tubes, and iron and steel
fittings” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2014, and conflicting national standards shall be withdrawn at the
latest by May 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8496:2004.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 8496:2013 has been approved by CEN as EN ISO 8496:2013 without any modification.
INTERNATIONAL ISO
STANDARD 8496
Third edition
2013-11-15
Metallic materials — Tube — Ring
tensile test
Matériaux métalliques — Tubes — Essai de traction sur anneaux
Reference number
ISO 8496:2013(E)
©
ISO 2013
ISO 8496:2013(E)
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

ISO 8496:2013(E)
Contents Page
Foreword .iv
1 Scope .
...