EN 10217-3:2002

Welded steel tubes for pressure purposes - Technical delivery conditions - Part 3: Alloy fine grain steel tubes

This Part of EN 10217 specifies the technical delivery condition in two test categories for welded tubes of circular cross section, made of weldable alloy fine grain steel.

Geschweißte Stahlrohre für Druckbeanspruchungen - Technische Lieferbedingungen - Teil 3: Rohre aus legierten Feinkornbaustählen

Dieser Teil der EN 10217 enthält die technischen Lieferbedingungen für geschweißte Rohre mit kreisförmigem Querschnitt aus schweißbaren legierten Feinkornbaustählen und legt dafür zwei Prüfkategorien fest.

Tubes soudés en acier pour service sous pression - Conditions techniques de livraison - Partie 3: Tubes en aciers allié à grain fin

La présente partie de l'EN 10217 spécifie les conditions techniques de livraison de deux catégories d'essai des tubes soudés à section circulaire, fabriqués en aciers alliés à grains fins.

Varjene jeklene cevi za tlačne posode - Tehnični dobavni pogoji - 3. del: Legirane jeklene cevi z drobnozrnato mikrostrukturo

General Information

• Status: Withdrawn
• Publication Date: 21-May-2002
• Withdrawal Date: 16-Apr-2019
• ICS: 23.040.10 - Iron and steel pipes
• ICS: 77.140.75 - Steel pipes and tubes for specific use
• Technical Committee: ECISS/TC 110 - Steel tubes, and iron and steel fittings
• Drafting Committee: ECISS/TC 29/SC 1 - Tubes for pressure purposes
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 17-Apr-2019
• Directive: 2014/68/EU - Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN 10217-3:2003 - Welded steel tubes for pressure purposes - Technical delivery conditions - Part 3: Alloy fine grain steel tubes

Relations

• Replaced By: EN 10217-3:2019 - Welded steel tubes for pressure purposes - Technical delivery conditions - Part 3: Electric welded and submerged arc welded alloy fine grain steel tubes with specified room, elevated and low temperature properties
• Effective Date: 24-Apr-2019
• Amended By: EN 10217-3:2002/A1:2005 - Welded steel tubes for pressure purposes - Technical delivery conditions - Part 3: Alloy fine grain steel tubes
• Effective Date: 08-Jun-2022

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Geschweißte Stahlrohre für Druckbeanspruchungen - Technische Lieferbedingungen - Teil 3: Rohre aus legierten FeinkornbaustählenTubes soudés en acier pour service sous pression - Conditions techniques de livraison - Partie 3: Tubes en aciers allié a grain finWelded steel tubes for pressure purposes - Technical delivery conditions - Part 3: Alloy fine grain steel tubes77.140.75Jeklene cevi in cevni profili za posebne nameneSteel pipes and tubes for specific use23.020.30MHNOHQNHPressure vessels, gas cylindersICS:Ta slovenski standard je istoveten z:EN 10217-3:2002SIST EN 10217-3:2003en01-april-2003SIST EN 10217-3:2003SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10217-3May 2002ICS 23.040.10; 77.140.75English versionWelded steel tubes for pressure purposes - Technical deliveryconditions - Part 3: Alloy fine grain steel tubesTubes soudés en acier pour service sous pression -Conditions techniques de livraison - Partie 3: Tubes enaciers allié à grain finGeschweißte Stahlrohre für Druckbeanspruchungen -Technische Lieferbedingungen - Teil 3: Rohre aus legiertenFeinkornbaustählenThis European Standard was approved by CEN on 25 April 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10217-3:2002 ESIST EN 10217-3:2003

Testing.3211.13Material identification.3311.14Retests, sorting and reprocessing.3312Marking.33SIST EN 10217-3:2003

European Standard series covering tubes for pressure purposes is:EN 10216:Seamless
steel tubes for pressure purposes.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark,Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway,Portugal, Spain, Sweden, Switzerland and the United Kingdom.SIST EN 10217-3:2003

of steel tubes Part 1 : Automatic electromagnetic testing of seamlessand welded
...