EN ISO 10350-1:2008

Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2007)

ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions. The properties included are those presented conventionally in manufacturers' data sheets.
ISO 10350-1:2007 applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials that may be injection- or compression-moulded or prepared as sheets of specified thickness. Part 2 of ISO 10350 deals specifically with long- or continuous-fibre-reinforced plastics. For the purposes of ISO 10350, long-fibre-reinforced plastics are considered to have fibre lengths greater than 7,5 mm prior to moulding.

Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte - Teil 1: Formmassen (ISO 10350-1:2007)

Die Reihe ISO 10350 legt spezifische Prüfverfahren zur Ermittlung und Darstellung vergleichbarer Kennwerte für bestimmte grundlegende Eigenschaften von Kunststoffen fest. Im Allgemeinen wird jede Eigen¬schaft durch einen einzelnen Messwert festgelegt, in bestimmten Fällen wird eine Eigenschaft jedoch durch zwei Werte charakterisiert, die unter verschiedenen Prüfbedingungen ermittelt wurden. Die aufgeführten Eigenschaften werden vom Hersteller üblicherweise in Datenblättern erfasst. Dieser Teil der Reihe ISO 10350 behandelt in erster Linie thermoplastische und duroplastische Kunststoffe mit oder ohne Verstärkung, die spritzgegossen, gepresst oder in Form von Platten mit festgelegter Dicke bereitgestellt werden. ISO 10350 2 befasst sich speziell mit Kunststoffen, die eine Verstärkung durch lange oder kontinuierliche Fasern haben. Für die Anwendung von ISO 10350 gelten solche Kunststoffe als langfaserverstärkt, die vor dem Formen eine Faserlänge von mehr als 7,5 mm haben.

Plastiques - Acquisition et présentation de caractéristiques intrinsèques comparables - Partie 1: Matériaux pour moulage (ISO 10350-1:2007)

L'ISO 10350 identifie des méthodes d'essai spécifiques en vue de l'acquisition et de la présentation de données comparables relatives à certaines propriétés de base des matières plastiques. En général, chaque propriété est spécifiée par une valeur expérimentale unique; toutefois, dans certains cas, certaines propriétés sont représentées par deux valeurs obtenues dans des conditions d'essai différentes. Les propriétés indiquées sont celles qui sont traditionnellement présentées dans les fiches techniques des fabricants.
L'ISO 10350-1:2007 est avant tout applicable aux matériaux thermodurcissables ou thermoplastiques, renforcés ou non, susceptibles d'être moulés par compression ou injection ou préparés en feuilles ayant une épaisseur spécifiée. La partie 2 de l'ISO 10350 traite spécifiquement des plastiques renforcés de fibres longues ou continues. Pour les besoins de l'ISO 10350, il est à noter que les plastiques renforcés de fibres longues ont des longueurs de fibre supérieures à 7,5 mm avant moulage.

Polimerni materiali - Pridobitev in predstavitev primerljivih značilnih enotočkovnih podatkov - 1. del: Materiali za oblikovanja (ISO 10350-1:2007)

Standard ISO 10350 določa posebne preskusne postopke za pridobitev in predstavitev primerljivih podatkov za nekatere osnovne lastnosti polimernih materialov. Na splošno vsako lastnost določa ena eksperimentalna vrednost, čeprav so v nekaterih primerih lastnosti predstavljene z dvema vrednostma, ki sta pridobljeni v različnih preskusnih pogojih. Vključene so tiste lastnosti, ki so običajno navedene v tehničnih listih proizvajalca. Ta del standarda ISO 10350 se večinoma uporablja za neojačene in ojačene plastomerne materiale in duromere, ki so lahko oblikovani z vbrizgavanjem ali s stiskanjem ali pripravljeni v obliki trakov določene debeline. 2. del standarda ISO 10350 obravnava zlasti polimerne materiale, ojačene z dolgimi vlakni ali z brezkončnimi vlakni. Za potrebe standarda ISO 10350 se za polimerne materiale, ojačene z dolgimi vlakni, štejejo polimerni materiali, katerih vlakna so pred oblikovanjem daljša od 7,5 mm.

General Information

• Status: Withdrawn
• Publication Date: 26-Aug-2008
• Withdrawal Date: 28-Nov-2017
• ICS: 83.080.01 - Plastics in general
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 29-Nov-2017
• Ref Project: SIST EN ISO 10350-1:2008 - Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2007)

Relations

• Replaces: EN ISO 10350-1:2000 - Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:1998)
• Effective Date: 22-Dec-2008
• Replaced By: EN ISO 10350-1:2017 - Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2017)
• Effective Date: 09-Dec-2015
• Amended By: EN ISO 10350-1:2008/A1:2014 - Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2007/Amd 1:2014)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2008
1DGRPHãþD
SIST EN ISO 10350-1:2001
3ROLPHUQLPDWHULDOL3ULGRELWHYLQSUHGVWDYLWHYSULPHUOMLYLK]QDþLOQLKHQRWRþNRYQLK
SRGDWNRYGHO0DWHULDOL]DREOLNRYDQMD,62
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding
materials (ISO 10350-1:2007)
Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte - Teil 1:
Formmassen (ISO 10350-1:2007)
Plastiques - Acquisition et présentation de caractéristiques intrinsèques comparables -
Partie 1: Matériaux pour moulage (ISO 10350-1:2007)
Ta slovenski standard je istoveten z: EN ISO 10350-1:2008
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 10350-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2008
ICS 83.080.20 Supersedes EN ISO 10350-1:2000
English Version
Plastics - Acquisition and presentation of comparable single-
point data - Part 1: Moulding materials (ISO 10350-1:2007)
Plastiques - Acquisition et présentation de caractéristiques Kunststoffe - Ermittlung und Darstellung vergleichbarer
intrinsèques comparables - Partie 1: Matériaux pour Einpunktkennwerte - Teil 1: Formmassen (ISO 10350-
moulage (ISO 10350-1:2007) 1:2007)
This European Standard was approved by CEN on 30 July 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10350-1:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.3

Foreword
The text of ISO 10350-1:2007 has been prepared by Technical Committee ISO/TC 61 “Plastics” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 10350-1:2008 by
Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by February 2009, and conflicting national standards shall be withdrawn
at the latest by February 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10350-1:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10350-1:2007 has been approved by CEN as a EN ISO 10350-1:2008 without any
modification.
INTERNATIONAL ISO
STANDARD 10350-1
Second edition
2007-07-15
Plastics — Acquisition and presentation
of comparable single-point data —
Part 1:
Moulding materials
Plastiques — Acquisition et présentation de caractéristiques
intrinsèques comparables —
Partie 1: Matériaux pour moulage

Reference number
ISO 10350-1:2007(E)
©
ISO 2007
.
ISO 10350-1:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved

ISO 10350-1:2007(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 3
4 Specimen preparation and conditioning. 3
5 Test requirements. 4
6 Presentation of results. 4

ISO 10350-1:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10350-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 2, Mechanical
properties.
This second edition cancels and replaces the first edition (ISO 10350-1:1998), which has been technically
revised.
ISO 10350 consists of the following parts, under the general title Plastics — Acquisition and presentation of
comparable single-point data:
⎯ Part 1: Moulding materials
⎯ Part 2: Long-fibre-reinforced plastics
iv © ISO 2007 – All rights reserved

ISO 10350-1:2007(E)
Introduction
ISO 10350 has been prepared because users of plastics find that available data cannot always be readily
used to compare the properties of similar materials, especially when the data have been supplied by different
sources. Even when the same standard tests have been used, they often allow the adoption of a wide range
of alternative test conditions, and the data obtained are not necessarily comparable. The purpose of this
International Standard is to identify specific methods and conditions of test to be used for the acquisition and
presentation of data in order that valid comparisons between materials can be made.
ISO 10350 is concerned with tests employed to present “single-point” data on the limited range of properties
commonly included in data sheets and used for the preliminary selection of materials. Such data represent the
most basic approach to the specification of properties of materials, and the standard thus facilitates the first
steps towards more efficient selection and use of plastics in the many applications to which they are suited.
1)
Complementary International Standards (ISO 11403-1, ISO 11403-2 and ISO 11403-3) are concerned with
the standardized acquisition and presentation of multipoint data, to demonstrate how properties vary with
important factors such as time, temperature and the presence of particular natural and chemical environments.
In these standards, some additional properties are included. Their use will provide a more substantial
database than one containing only single-point data, and so will enable improved assessment of the fitness of
a material for any particular application. In addition, ISO 11403-1, which deals with mechanical properties,
assists predictions of the performance of components and ISO 11403-2, covering thermal and processing
properties, aids predictions of melt-flow behaviour during manufacturing. ISO 11403-3 is concerned with
environmental influences on properties, and other parts may be prepared to cover additional properties.

1) ISO 11403-1, Plastics — Acquisition and presentation of comparable multipoint data — Part 1: Mechanical properties
ISO 11403-2, Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and
processing properties
ISO 11403-3, Plastics — Acquisition and presentation of comparable multipoint data — Part 3: Environmental
influences on properties
INTERNATIONAL STANDARD ISO 10350-1:2007(E)

Plastics — Acquisition and presentation of comparable single-
point data —
Part 1:
Moulding materials
1 Scope
ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for
certain basic properties of plastics. In general, each property is specified by a single experimental value,
although in certain cases properties are represented by two values obtained under different test conditions.
The properties included are those presented conventionally in manufacturers' data sheets. This part of
ISO 10350 applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials
that may be injection- or compression-moulded or prepared as sheets of specified thickness. Part 2 of
ISO 10350 deals specifically with long- or continuous-fibre-reinforced plastics. For the purposes of ISO 10350,
long-fibre-reinforced plastics are considered to have fibre lengths greater than 7,5 mm prior to moulding.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 62, Plastics — Determination of water absorption
ISO 75-1, Plastics — Determination of temperature of deflection under load — Part 1: General test method
ISO 75-2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 178, Plastics — Determination of flexural properties
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 293, Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 294-1, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General
...