LPG equipment and accessories - Pressure relief valves for LPG pressure vessels - Ancillary equipment

This European Standard specifies the design, testing and inspection requirements for pressure relief valve isolating devices, valve manifolds, vent pipes and system assemblies which are, where necessary, used with pressure relief valves for use in static pressure vessels for Liquefied Petroleum Gas (LPG) service.
This European Standard addresses both prototype testing and production testing of isolating devices and PRV manifolds.
Pressure relief valves for LPG pressure vessels are specified in EN 14129:2014.

Flüssiggas-Geräte und Ausrüstungsteile - Druckentlastungsventile für Druckbehälter für Flüssiggas (LPG) - Zusatzausrüstung

Diese Europäische Norm legt Anforderungen an die Auslegung, Prüfungen und Inspektion von Absperreinrichtungen für Druckentlastungsventile, Ventilsammelleitungen, Entlüftungsrohren und Systembaugruppen fest, welche bei Bedarf zusammen mit Druckentlastungsventilen für Druckbehälter für den Betrieb mit Flüssiggas (LPG, en: Liquefied Petroleum Gas) verwendet werden.
Druckentlastungsventile für LPG-Behälter sind in EN 14129 festgelegt.

Équipements pour GPL et leurs accessoires - Soupapes de sécurité des réservoirs de gaz de pétrole liquéfié (GPL) - Équipement auxiliaire

La présente Norme européenne spécifie les exigences en matière de conception, essais et inspection relatives aux clapets porte-soupape pour soupapes de sécurité, collecteurs de soupapes, prolongateurs de soupapes et systèmes d'assemblage utilisés, lorsque nécessaire, avec les soupapes de sécurité destinées à être installées sur des réservoirs sous pression statiques contenant du gaz de pétrole liquéfié (GPL).
La présente Norme européenne traite à la fois des essais sur prototype et des essais de production des clapets porte-soupape et des collecteurs de soupape.
Les soupapes de sécurité pour réservoirs GPL sous pression sont spécifiées dans l'EN 14129:2014.

Oprema in pribor za utekočinjeni naftni plin (UNP) - Varnostni ventili za tlačne posode za UNP - Pomožna oprema

General Information

Status
Not Published
Current Stage
5060 - Closure of Vote - Formal Approval
Start Date
31-Jan-2019
Due Date
19-May-2019
Completion Date
31-Jan-2019

Relations

Buy Standard

Draft
EN 14071:2015/oprA1:2017
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 14071:2015/oprA1:2017
01-december-2017
2SUHPDLQSULERU]DXWHNRþLQMHQLQDIWQLSOLQ 813 9DUQRVWQLYHQWLOL]DWODþQH
SRVRGH]D8133RPRåQDRSUHPD
LPG equipment and accessories - Pressure relief valves for LPG pressure vessels -
Ancillary equipment
Flüssiggas-Geräte und Ausrüstungsteile - Druckentlastungsventile für Behälter für
Flüssiggas (LPG) - Zusatzausrüstung
Équipements pour GPL et leurs accessoires - Soupapes de sécurité des réservoirs de
gaz de pétrole liquéfié (GPL) - Équipement auxiliaire
Ta slovenski standard je istoveten z: EN 14071:2015/prA1
ICS:
23.020.32 7ODþQHSRVRGH Pressure vessels
23.060.40 7ODþQLUHJXODWRUML Pressure regulators
SIST EN 14071:2015/oprA1:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 14071:2015/oprA1:2017

---------------------- Page: 2 ----------------------

SIST EN 14071:2015/oprA1:2017


DRAFT
EUROPEAN STANDARD
EN 14071:2015
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA1
November 2017
ICS 23.060.40
English Version

LPG equipment and accessories - Pressure relief valves for
LPG pressure vessels - Ancillary equipment
Équipements pour GPL et leurs accessoires - Soupapes Flüssiggas-Geräte und Ausrüstungsteile -
de sécurité des réservoirs de gaz de pétrole liquéfié Druckentlastungsventile für Behälter für Flüssiggas
(GPL) - Équipement auxiliaire (LPG) - Zusatzausrüstung
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 286.

This draft amendment A1, if approved, will modify the European Standard EN 14071:2015. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14071:2015/prA1:2017:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 14071:2015/oprA1:2017
EN 14071:2015/prA1:2017 (E)
Contents Page
European foreword . 3
1 Modification to 9.1 . 4
2 Modification to 9.2 . 4
3 Modification to Annex ZA . 4

2

---------------------- Page: 4 ----------------------

SIST EN 14071:2015/oprA1:2017
EN 14071:2015/prA1:2017 (E)
European foreword
This document (EN 14071:2015/prA1:2017) has been prepared by Technical Committee CEN/TC 286
“LPG equipment and accessories”, the secretariat of which is held by NSAI.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of
EN 14071:2015.
3

---------------------- Page: 5 ----------------------

SIST EN 14071:2015/oprA1:2017
EN 14071:2015/prA1:2017 (E)
1 Modification to
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.