iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14444:2005

(Main)

Structural adhesives - Qualitative assessment of durability of bonded assemblies - Wedge rupture test (ISO 10354:1992 modified)

Structural adhesives - Qualitative assessment of durability of bonded assemblies - Wedge rupture test (ISO 10354:1992 modified)

This document simulates in a qualitative manner mechanical forces and important environmental influences on an adhesive-bonded joint at a metal polymer interfaces it can also be used as a method of checking the surface preparation of substrates, with a limited detection level.
The test is applicable at the present time to the bonding of aluminium and titanium alloys using thermosetting structural adhesives and primers.
NOTE   This method can also be used for assessing surface preparation of other metals. Considerable caution in the evaluation of comparative results should be exercised in the event that the materials (adhesive plus adherend) and the specimen geometry are varied. Like should be compared with like (only similar adherends bonded with similar adhesives can be compared between themselves).

Strukturklebstoffe - Qualitative Bestimmung der Beständigkeit geklebter Baugruppen - Keilberstprüfung (ISO 10354:1992 modifiziert)

Dieses Dokument legt ein Verfahren fest, das auf qualitative Art und Weise mechanische Kräfte und wichtige
Umwelteinflüsse auf Klebverbindungen an einer Metall/Polymer-Grenzfläche simuliert. Es kann auch als
Verfahren mit beschränkter Nachweisgrenze zur Überprüfung der Oberflächenvorbehandlung von Substraten
verwendet werden.
Die Prüfung ist gegenwärtig auf das Fügen von Aluminium- und Titanlegierungen mit wärmehärtenden
Strukturklebstoffen und Haftvermittlern anwendbar.
ANMERKUNG Dieses Verfahren kann auch zur Bestimmung der Oberflächenvorbehandlung anderer Metalle
verwendet werden. Falls die Werkstoffe (Klebstoff und Fügeteil) und die Probengeometrie variiert werden, sollte höchste
Vorsicht bei der Auswertung von Vergleichsergebnissen gewahrt werden. Gleiches sollte mit Gleichem verglichen werden
(nur ähnliche Fügeteile, geklebt mit ähnlichen Klebstoffen können miteinander verglichen werden).

Adhésifs structuraux - Évaluation qualitative de la durabilité des assemblages collés - Essai de clivage au coin (ISO 10354:1992 modifiée)

La présente Norme européenne simule de manière qualitative les forces mécaniques et les influences
environnementales importantes sur un assemblage collé à l�interface métal-polymère. Elle est également un
moyen de contrôle de la préparation de surface des substrats, avec un niveau de détection limitée.
L�essai s�applique à l�heure actuelle au collage d�alliages d�aluminium et de titane, utilisant des adhésifs
structuraux thermodurcissables et des primaires.
NOTE La méthode peut également être utilisée pour caractériser la préparation de surface d�autres métaux. Pour
cela, il convient de prendre beaucoup de précautions dans l�évaluation des résultats comparatifs dans le cas où les
matériaux (adhésif + support) et la géométrie de l�éprouvette varient. Il convient de comparer ce qui est comparable (seuls
des supports identiques collés avec des adhésifs identiques peuvent être comparés entre eux).

Konstrukcijska lepila – Kvalitativno ugotavljanje trdnosti lepljenih spojev - Preskus pretrganja s klinom (ISO 10354:1992, spremenjen)

General Information

Status
Published
Publication Date
18-Oct-2005
ICS
83.180 - Adhesives
Technical Committee
CEN/TC 193 - Adhesives
Drafting Committee
CEN/TC 193/WG 2 - Structural adhesives
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
22-Oct-2020
Ref Project
SIST EN 14444:2006 - Structural adhesives - Qualitative assessment of durability of bonded assemblies - Wedge rupture test (ISO 10354:1992 modified)

Relations

Corrected By
EN 14444:2005/AC:2008 - Structural adhesives - Qualitative assessment of durability of bonded assemblies - Wedge rupture test (ISO 10354:1992 modified)
Effective Date
22-Dec-2008
Revised
EN 14680:2015 - Adhesives for non-pressure thermoplastics piping systems - Specifications
Effective Date
07-Mar-2012

Buy Standard

EN 14444:2006EN 14444:2006
PreviousNext
Standard
EN 14444:2006
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 14444:2006
01-januar-2006
Konstrukcijska lepila – Kvalitativno ugotavljanje trdnosti lepljenih spojev -
Preskus pretrganja s klinom (ISO 10354:1992, spremenjen)
Structural adhesives - Qualitative assessment of durability of bonded assemblies -
Wedge rupture test (ISO 10354:1992 modified)
Strukturklebstoffe - Qualitative Bestimmung der Beständigkeit geklebter Baugruppen -
Keilberstprüfung (ISO 10354:1992 modifiziert)
Adhésifs structuraux - Évaluation qualitative de la durabilité des assemblages collés -
Essai de clivage au coin (ISO 10354:1992 modifiée)
Ta slovenski standard je istoveten z: EN 14444:2005
ICS:
83.180 Lepila Adhesives
SIST EN 14444:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 14444:2006

---------------------- Page: 2 ----------------------

SIST EN 14444:2006
EUROPEAN STANDARD
EN 14444
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2005
ICS 83.180

English Version
Structural adhesives - Qualitative assessment of durability of
bonded assemblies - Wedge rupture test (ISO 10354:1992
modified)
Adhésifs structuraux - Évaluation qualitative de la durabilité Strukturklebstoffe - Qualitative Bestimmung der
des assemblages collés - Essai de clivage au coin (ISO Beständigkeit geklebter Baugruppen - Keilberstprüfung
10354:1992 modifiée) (ISO 10354:1992 modifiziert)
This European Standard was approved by CEN on 13 June 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14444:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 14444:2006
EN 14444:2005 (E)
Contents
Page
Foreword .3
1 Scope.4
2 Normative references.4
3 Principle.4
4 Safety.4
5 Apparatus.5
6 Procedure.5
6.1 Preparation of specimens.5
6.2 Number of specimens.6
6.3 Determination.6
7 Expression of results.7
8 Precision.8
9 Test report.8

2

---------------------- Page: 4 ----------------------

SIST EN 14444:2006
EN 14444:2005 (E)
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 10364:2024(Main)
Structural adhesives - Determination of the pot life (working life) of multi-component adhesives (ISO 10364:2024)
SIST EN ISO 10364:2024

This document specifies methods for determining the pot life of multi-part adhesives, in order to be able to determine whether the pot life conforms to the minimum specified working life required of an adhesive.
The different methods described in this document to measure the property do not necessarily provide identical results.
The test methods described are suitable for assessing all multi–part adhesives, and especially epoxy based and polyurethane based adhesives, but they are not suitable for some acrylic-based adhesives.
NOTE 1       Some of the methods described in this document can also be suitable for determination of working life of one-part adhesives that react to humidity (e.g. PUR prepolymers).
NOTE 2       This document can also be used for assessing non-structural adhesives.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21368:2023(Main)
Adhesives - Guidelines for the fabrication of adhesively bonded structures and reporting procedures suitable for the risk evaluation of such structures (ISO 21368:2022)
SIST EN ISO 21368:2023

This document provides guidelines describing the adhesive bonding quality requirements suitable for use by adhesive user-companies utilizing adhesive bonding as a means of fabrication. In particular, the guidelines define various approaches to meeting quality requirements for fabrication and reporting procedures, both in workshops and on site. These guidelines aim to convey the importance of maintaining quality standards in fabrication and reporting procedures, keeping records and thus enabling documentation to provide the basis for risk evaluation of adhesively bonded structures in service and in use.
These guidelines have been prepared such that:
a) they are independent of the type of adhesively bonded structure;
b) they are independent of adhesive user-companies’ and suppliers’ product recommendations;
c) they define the quality requirements for adhesive bonding in terms of fabrication and reporting procedures, both in workshops and on site;
d) they can be used as the basis for risk evaluation of adhesively bonded structures in service and in use;
e) they can be used as a basis for assessing a fabricator's capability to produce adhesively bonded structures fulfilling specified quality requirements when they are detailed in one or more of the following:
—    a contract between the parties involved;
—    an application standard;
—    a regulatory statement.
The guidelines contained within this document can be adopted in full or selectively chosen by the adhesive user to suit the structure concerned. The guidelines provide a flexible framework for the control of adhesive bonding activities in the following cases.
Case 1
The provision of specific requirements for adhesive bonding in contracts that require the adhesive user to have a quality system other than ISO 9001.
Case 2
The provision of specific requirements for adhesive bonding as guidance to an adhesive user developing a quality system.
Case 3
The provision of specific requirements for references in application standards that uses adhesive bonding as part of its requirements or in a contract between relevant parties.
Case 4
The provision of a framework for fabrication and reporting procedures to a quality standard, suitable in particular as a basis for the risk evaluation of adhesively bonded structures.

  • Standard
    111 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6076:2023(Main)
Adhesives - Installation of floor coverings, wood flooring, levelling compounds and tiles - Specification of trowel notch sizes (ISO 6076:2023, Corrected version 2023-09)
SIST EN ISO 6076:2023

This document specifies the individual measurements of notches. It assigns specific codes used to label notched tools according to the measurements and tolerances specified in this document.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-8:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 8: Static load test of multiple bond line specimens in compression shear
SIST EN 302-8:2023

This document specifies a method of determining the ability of adhesive bonds to resist static load. It is applicable to adhesives used in load bearing timber structures.
It is applicable for the following applications:
a) for assessing the compliance of adhesives according to EN 301, EN 15425, EN 16254, EN 17334 and EN 17418;
b) for assessing the suitability and quality of adhesives for load-bearing timber structures;
c) for assessing the effect on the bond strength resulting from constant load at different climate conditions.
This method is intended primarily to obtain performance data for the classification of adhesives for load bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 301:2023(Main)
Adhesives, phenolic and aminoplastic, for load-bearing timber structures - Classification and performance requirements
SIST EN 301:2023

This document establishes a classification for phenolic and aminoplastic polycondensation adhesives according to their suitability for use for load-bearing timber products in defined climatic exposure conditions, and specifies performance requirements for such adhesives for the factory manufacture or factory-like manufacturing conditions of load-bearing timber products only.
This document only specifies the performance of an adhesive for use in an environment corresponding to the defined conditions.
The performance requirements of this document are applicable to the adhesive only, not to the manufacturing timber products. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) or the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. acetylated wood, heat treated wood and polymer impregnated wood.
This document is primarily intended for use by adhesive manufacturers and for use in timber products bonded with adhesives, to assess or control the quality of adhesives. The requirements are applicable to the type testing of the adhesives. Production control activities are outside the scope of this document.
Adhesives meeting the requirements of this document are adequate for use in load-bearing timber products, provided that the bonding process has been carried out according to an appropriate product standard.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-7:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 7: Determination of the working life under referenced conditions
SIST EN 302-7:2023

This document specifies a method for determining the working life for adhesives mixed with hardener for load-bearing timber structures, by a viscosity test.
This method does not apply to determining the working life of a multi-component adhesive whose actual working life is very short.
This document is only intended for obtaining a reliable basis for comparison between adhesives. The method gives results which cannot be applied to the safe manufacture of timber structures without modifications for the influences of factory temperature and relative air humidity.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-4:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 4: Determination of the effects of wood shrinkage on the shear strength
SIST EN 302-4:2023

This document specifies a method for determining the influence of shear strength in crosswise gluing by wood shrinkage under drying conditions.
It is applicable for the following applications:
a)   for assessing the compliance of adhesives with EN 301, EN 15425, EN 16254, EN 17334 and EN 17418;
b)   for assessing the suitability and quality of adhesives for load-bearing timber structures;
c)   for determining if the adhesive is capable of withstanding stresses due to wood shrinkage without unacceptable loss of strength.
This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments. This test is carried out on Norway spruce (Picea abies L.).
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-2:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 2: Determination of resistance to delamination
SIST EN 302-2:2023

This document specifies a method for determining the resistance to delamination in glue lines.
It is applicable to the following applications:
a)   for assessing the compliance of adhesives with EN 301, EN 15425, EN 16254, EN 17334 and EN 17418;
b)   for assessing the suitability and quality of adhesives for load-bearing timber structures;
c)   for comparing the effects on the bond strength resulting from the choice of bonding conditions, from different climatic conditioning and from the treatment of the test pieces before and after bonding.
This test does not apply to modified and stabilized wood with strongly reduced swelling and shrinkage properties, such as acetylated wood, heat-treated wood and polymer impregnated wood.
This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15425:2023(Main)
Adhesives - One component polyurethane (PUR) for load-bearing timber structures - Classification and performance requirements
SIST EN 15425:2023

This document establishes a classification for one component polyurethane (PUR) adhesives according to their suitability for use in load-bearing timber products in defined climatic exposure conditions, and specifies performance requirements for such adhesives for the factory manufacture or factory-like manufacturing of load-bearing timber products only.
It also classifies “adhesive product lines” where all the products within the line have the same chemical composition except for a different amount of catalyst.
This document only specifies the performance of adhesives for use in an environment corresponding to the defined conditions.
The performance requirements of this document are applicable to the adhesives only, not to the manufactured timber products. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) or the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. acetylated wood, heat treated wood and polymer impregnated wood.
This document is primarily intended for use by adhesive manufacturers and for use in timber products bonded with adhesives, to assess or control the quality of adhesives. The requirements are applicable to the type testing of the adhesives. Production control activities are outside the scope of this document.
Adhesives meeting the requirements of this document are adequate for use in load-bearing timber products, provided that the bonding process has been carried out according to an appropriate product standard.
This document does not address the classification and use of adhesives in combination with the spraying of water before or during the bonding process; see informative Annex C of this document.
This does neither allow nor forbid the use of adhesives in combination with the spraying of water.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-6:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 6: Determination of the minimum pressing time under referenced conditions
SIST EN 302-6:2023

This document specifies a method of determining the minimum pressing time for two glue line thicknesses, close contact glue line and thick glue line (between 0,3 mm and 8 mm), at three temperatures. It is applicable to adhesives used in load-bearing timber products.
This document is only intended for obtaining a reliable base of comparison of pressing time between adhesives. The method gives results that cannot be applied to the safe manufacture of timber structures without modifications for the influences of timber density/absorbency, moisture content, factory temperature and relative air humidity.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day