prEN 13763-2
(Main)Explosives for civil uses - Detonators and detonating cord relays - Part 2: Verification of thermal stability at high temperatures
Explosives for civil uses - Detonators and detonating cord relays - Part 2: Verification of thermal stability at high temperatures
This document specifies a method for verification of the thermal stability of electric detonators, non-electric detonators, plain detonators, electronic detonators, surface connectors, detonating cord relays and shock tubes for use with electronic and non-electric detonators.
This document applies to explosives for civil uses.
Explosives become more stable in low temperatures and therefore this method does not include temperatures lower than (75 ± 2) °C.
Explosivstoffe für zivile Zwecke - Zünder und Sprengschnurverbinder - Teil 2: Überprüfung der thermischen Stabilität bei hohen Temperaturen
Dieses Dokument legt ein Verfahren für die Überprüfung der thermischen Stabilität von elektrischen Zündern, nichtelektrischen Zündern, Sprengkapseln, elektronischen Zündern, Oberflächenverbindern, Sprengschnurverzögerern und Zündschläuchen zur Verwendung mit elektronischen und nichtelektronischen Zündern fest.
Dieses Dokument ist anzuwenden für Explosivstoffe für zivile Zwecke.
Explosivstoffe werden bei niedrigen Temperaturen stabiler und daher berücksichtigt dieses Verfahren keine Temperaturen unter (75 ± 2) °C.
Explosifs à usage civil - Détonateurs et relais pour cordeau détonant - Partie 2 : Vérification de la stabilité thermique à haute température
Le présent document spécifie une méthode de vérification de la stabilité thermique des détonateurs électriques, des détonateurs non électriques, des détonateurs pyrotechniques, des détonateurs électroniques, des connecteurs de surface, des relais pour cordeau détonant ainsi que des tubes à transmission d’onde de choc utilisés avec des détonateurs non électriques et électroniques.
Le présent document s’applique aux explosifs à usage civil.
Les explosifs sont plus stables à basse température, c’est pourquoi cette méthode n’inclut pas les températures inférieures à (75 ± 2) °C.
Eksplozivi za civilno uporabo - Detonatorji in zakasnilniki - 2. del: Ugotavljanje toplotne stabilnosti
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 13763-2:2021
01-april-2021
Eksplozivi za civilno uporabo - Detonatorji in zakasnilniki - 2. del: Ugotavljanje
toplotne stabilnosti
Explosives for civil uses - Detonators and relays - Part 2: Determination of thermal
stability
Explosivstoffe für zivile Zwecke - Zünder und Verzögerungselemente - Teil 2:
Bestimmung der thermischen Stabilität
Explosifs à usage civil - Détonateurs et relais - Partie 2: Détermination de la stabilité
thermique
Ta slovenski standard je istoveten z: prEN 13763-2
ICS:
71.100.30 Eksplozivi. Pirotehnika in Explosives. Pyrotechnics and
ognjemeti fireworks
oSIST prEN 13763-2:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 13763-2:2021
---------------------- Page: 2 ----------------------
oSIST prEN 13763-2:2021
DRAFT
EUROPEAN STANDARD
prEN 13763-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2021
ICS 71.100.30 Will supersede EN 13763-2:2002
English Version
Explosives for civil uses - Detonators and detonating cord
relays - Part 2: Verification of thermal stability at high
temperatures
Explosifs à usage civil - Détonateurs et relais pour Explosivstoffe für zivile Zwecke - Zünder und
cordeau détonant - Partie 2: Vérification de la stabilité Sprengschnurverbinder - Teil 2: Überprüfung der
thermique à hautes températures thermischen Stabilität bei hohen Temperaturen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 321.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13763-2:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 13763-2:2021
prEN 13763-2:2021 (E)
Contents Page
European foreword . 3
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Principle . 6
5 Apparatus . 6
6 Preparation and handling of test samples and test pieces . 6
6.1 Handling of test samples . 6
6.2 Detonators . 6
6.2.1 Electric detonators .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.