iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

prEN 1991-1-7

(Main)

Eurocode 1 - Actions on structures - Part 1-7: Accidental actions

Eurocode 1 - Actions on structures - Part 1-7: Accidental actions

1.1   Scope of prEN 1991-1-7
(1) prEN 1991 1 7 provides actions and rules for safeguarding buildings and other civil engineering works against identifiable accidental actions.
NOTE 1   Identifiable accidental actions include impact from vehicles and internal explosions.
NOTE 2    Rules on impact from vehicles travelling on a bridge deck are given in prEN 1991 2.
(2) prEN 1991 1 7 also covers actions and rules for tying systems and key members; information on risk assessment; dynamic design for impact; actions for internal explosions; actions from debris.
1.2   Assumptions
(1) The general assumptions of EN 1990 apply to prEN 1991 1 7.
(2) prEN 1991 1 7 is intended to be used in conjunction with EN 1990, EN 1991 (all parts) and the other Eurocode parts for the design of structures.

Eurocode 1 - Einwirkungen auf Tragwerke - Teil 1-7: Außergewöhnliche Einwirkungen

1.1   Anwendungsbereich von prEN 1991 1 7
(1) prEN 1991 1 7 enthält Einwirkungen und Regelungen für die Sicherung von Hochbauten und anderen Ingenieurbauwerken gegen identifizierbare außergewöhnliche Einwirkungen.
ANMERKUNG 1   Identifizierbare außergewöhnliche Einwirkungen umfassen Anpralllasten durch Fahrzeuge und Innenraumexplosionen.
ANMERKUNG 2   Regelungen für Anpralllasten durch Fahrzeuge auf einem Brückenüberbau sind in EN 1991 2 angegeben.
(2) prEN 1991 1 7 behandelt außerdem Einwirkungen und Regelungen für Zugverankerungssysteme und Haupttragelemente; Informationen zur Risikobeurteilung; dynamische Anprallberechnungen; Einwirkungen durch Innenraumexplosionen; Einwirkungen aus Trümmern.
1.2   Annahmen
(1) Für prEN 1991 1 7 gelten die allgemeinen Annahmen von EN 1990.
(2) prEN 1991 1 7 ist dafür vorgesehen, zusammen mit EN 1990, EN 1991 (alle Teile) und den anderen Eurocode-Teilen für die Bemessung und Konstruktion von Tragwerken angewendet zu werden.

Eurocode 1 - Actions sur les structures - Partie 1-7: Actions accidentelles

1.1   Domaine d'application du prEN 1991-1-7
(1) Le prEN 1991 1 7 fournit des actions et des règles pour préserver les bâtiments et autres ouvrages de génie civil contre les actions accidentelles identifiables.
NOTE 1   Les actions accidentelles identifiables incluent les chocs produits par des véhicules et des explosions intérieures.
NOTE 2   Les règles relatives aux chocs produits par des véhicules circulant sur un tablier de pont sont données dans le prEN 1991 2.
(2) Le prEN 1991 1 7 spécifie également des actions et des règles pour les tirants et les éléments clefs ; des informations sur l'évaluation des risques ; le calcul dynamique pour le choc ; des actions pour les explosions intérieures ; des actions dues aux débris.
1.2   Hypothèses
(1) Les hypothèses générales de l'EN 1990 s'appliquent au prEN 1991 1 7.
(2) Le prEN 1991 1 7 est destiné à être utilisé avec l'EN 1990, l'EN 1991 (toutes les parties) et les autres parties de l'Eurocode pour le calcul des structures.

Evrokod 1: Vplivi na konstrukcije -1-7. del: Nezgodni vplivi

General Information

Status
Not Published
Publication Date
12-Jun-2025
ICS
91.010.30 - Technical aspects
Technical Committee
CEN/TC 250 - Structural Eurocodes
Drafting Committee
CEN/TC 250/SC 1/WG 7 - Evolution of EN 1991-1-1, EN 1991-1-6, EN 1991-1-7 and EN 1991-3
Current Stage
4060 - Closure of enquiry - Enquiry
Start Date
28-Dec-2023
Due Date
19-Jul-2023
Completion Date
28-Dec-2023
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
Mandate
M/515 - Mandate for amending existing Eurocodes and extending the scope of structural Eurocodes
Ref Project
oSIST prEN 1991-1-7:2023 - Eurocode 1 - Actions on structures - Part 1-7: Accidental actions

Relations

Revises
EN 1991-1-7:2006 - Eurocode 1 - Actions on structures - Part 1-7: General actions - Accidental actions
Effective Date
18-Jan-2023

Buy Standard

prEN 1991-1-7:2023 - BARVEprEN 1991-1-7:2023 - BARVE
PreviousNext
Draft
prEN 1991-1-7:2023 - BARVE
English language
67 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 1991-1-7:2023
01-december-2023
Nadomešča:
SIST EN 1991-1-7:2006
Evrokod 1: Vplivi na konstrukcije -1-7. del: Nezgodni vplivi
Eurocode 1 - Actions on structures - Part 1-7: Accidental actions
Eurocode 1 - Einwirkungen auf Tragwerke - Teil 1-7: Außergewöhnliche Einwirkungen
Eurocode 1 - Actions sur les structures - Partie 1-7: Actions accidentelles
Ta slovenski standard je istoveten z: prEN 1991-1-7
ICS:
91.010.30 Tehnični vidiki Technical aspects
oSIST prEN 1991-1-7:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 1991-1-7:2023

---------------------- Page: 2 ----------------------
oSIST prEN 1991-1-7:2023


DRAFT
EUROPEAN STANDARD
prEN 1991-1-7
NORME EUROPÉENNE

EUROPÄISCHE NORM

September 2023
ICS 91.010.30
English Version

Eurocode 1 - Actions on structures - Part 1-7: Accidental
actions
Eurocode 1 - Actions sur les structures - Partie 1-7: Eurocode 1 - Einwirkungen auf Tragwerke - Teil 1-7:
Actions accidentelles Außergewöhnliche Einwirkungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 250.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1991-1-7:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 1991-1-7:2023
prEN 1991-1-7:2023 (E)
Contents Page
European foreword . 4
0 Introduction . 5
1 Scope . 8
1.1 Scope of prEN 1991-1-7 . 8
1.2 Assumptions . 8
2 Normative references . 8
3 Terms, definitions and symbols . 8
3.1 Terms and definitions . 8
3.2 Symbols . 12
4 Basis of design . 13
4.1 General strategies . 13
4.2 Accidental design situations — strategies for identified accidental actions .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 1993-1-3:2024(Main)
Eurocode 3 - Design of steel structures - Part 1-3: Cold-formed members and sheeting
kSIST FprEN 1993-1-3:2023

1.1   Scope of prEN 1993-1-3
(1) This document provides rules for structural design of cold-formed steel members and sheeting.
(2) This document applies to cold-formed steel products made from coated or uncoated hot- or cold-rolled sheet or strip, which have been cold-formed by processes such as roll-forming or press braking. It also covers sheeting and members which are curved during fabrication by continuous bending or roll-forming. Sheeting which has the curvature created by crushing the inner flanges is not included. This document is also applicable to the design of profiled steel sheeting for composite steel and concrete slabs at the construction stage, see EN 1994. The execution of steel structures made of cold-formed steel members and sheeting is covered in EN 1090 4. Provisions for bolted connections are provided in EN 1090 2.
NOTE   The rules in prEN 1993 1 3 complement the rules in other parts of EN 1993 1.
(3) Methods are also given for stressed-skin design, using steel sheeting as a structural diaphragm.
(4) This document does not apply to cold-formed circular and rectangular structural hollow sections supplied to EN 10219, for which reference is made to EN 1993 1 1 and EN 1993 1 8.
(5) This document provides methods for design by calculation and for design assisted by testing. The methods for design by calculation apply only within the stated ranges of material properties and geometric proportions, for which sufficient experience and test evidence is available. These limitations do not apply to design assisted by testing.
1.2   Assumptions
(1) Unless specifically stated, EN 1990, EN 1991 (all parts) and EN 1993 1 1 apply.
(2) The design methods given in prEN 1993 1 3 are applicable if:
-   the execution quality is as specified in EN 1090 4, the execution quality of bolted connections is as specified in EN 1090 2, and
-   the construction materials and products are as specified in the relevant parts of EN 1993 (all parts), or in the relevant material and product specifications.
(2) EN 1993 is intended to be used in conjunction with:
-   the parts of EN 1992 to EN 1999 where steel structures or steel components are referred to within those documents;
-   EN, EAD and ETA standards for construction products relevant to steel structures.

  • Draft
    208 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1993-1-8:2024(Main)
Eurocode 3 - Design of steel structures - Part 1-8: Joints
kSIST FprEN 1993-1-8:2023

1.1   Scope of FprEN 1993-1-8
(1) FprEN 1993-1-8 provides rules for structural design of joints subject to predominantly static loading using all steel grades from S235 up to and including S700, unless otherwise stated in individual clauses.
NOTE   As an alternative to the design rules provided in Clause 9, the design rules given in CEN/TR 1993-1-801 "Eurocode 3: Design of steel structures - Part 1 801: Hollow section joints design according to the component method" can be used.
(2) The provisions in this document apply to steels complying with the requirements given in EN 1993 1 1 and to material thickness greater than or equal to 3 mm, unless otherwise stated in individual clauses.
1.2   Assumptions
(1) Unless specifically stated, EN 1990, EN 1991 (all parts) and the other relevant parts of EN 1993-1 (all parts) apply.
(2) The design methods given in FprEN 1993-1-8 are applicable if:
-   the execution quality is as specified in EN 1090-2,
and
-   the construction materials and products used are as specified in the relevant parts of EN 1993 (all parts), or in the relevant material and product specifications.

  • Draft
    197 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1993-1-13:2024(Main)
Eurocode 3 - Design of steel structures - Part 1-13: Beams with large web openings
kSIST FprEN 1993-1-13:2023

1.1   Scope of EN 1993-1-13
1.1.1   General
(1) This document gives supplementary provisions that extend the application of EN 1993-1-1 and EN 1993-1-5 to the design of rolled and welded steel sections with various shapes of web openings. The following cases are considered:
-   rolled or welded beams with single or widely spaced web openings;
-   rolled or welded beams with closely spaced web openings;
-   cellular beams with circular openings made by cutting and re-welding two parts of steel sections that may be different in dimensions;
-   beams with hexagonal and sinusoidal openings made by cutting and re-welding two parts of steel sections that may be different in dimensions.
(2) This document applies to uniform members with I or H profiles, which are symmetric about the weak axis. It does not apply to non-prismatic or curved beams although the same principles can apply.
(3) This document applies to steel beams with web openings that are subjected to sagging (positive) or to hogging (negative) bending moments.
(4) This document covers the verification of the resistance at the openings and their effects on the global behaviour of the beam, including lateral torsional buckling.
(5) Alternative methods are presented for beams with circular openings and with sinusoidal openings in which the forces and resistances are calculated by increments around or along the openings and which are suitable for computer methods.
(6) This document applies to web slenderness, hw/tw, not exceeding 121ε. The local checks at and between adjacent openings apply to web slenderness up to this limit. The material parameter ε is defined in EN 1993-1-1:2022, 5.2.5 (2).
NOTE   The limit of 121ε is the limit of a Class 4 web for a steel section with equal flanges. It is used as a convenient limit for the application of this document, including mono-symmetric sections.
(7) This document does not cover fatigue. In case of fatigue, EN 1993-1-9 applies.
(8) This document does not cover fire design. For the design in case of fire, EN 1993-1-2 applies.
(9) This document does not cover the buckling verification of members with web openings under axial force.
1.1.2   Shapes of web openings
(1) The different shapes of web openings that are considered in this document are shown in Figure 1.1.
Figure 1.1 - Different shapes of web openings in steel beams
1.1.3   Stiffened openings
(1) This document also covers openings in the web of beams that are reinforced by longitudinal stiffeners and/or transverse stiffeners on one or both sides of the web, see Figure 1.2.
NOTE   The National Annex can give rules for alternative types of stiffener.
Figure 1.2 - Stiffening of openings in beam webs
1.2   Assumptions
(1) Unless specifically stated, EN 1990, the EN 1991 series and EN 1993-1-1 apply.
(2) The design methods given in EN 1993-1-13 are applicable if:
-   the execution quality is as specified in EN 1090-2, and
-   the construction materials and products used are as specified in the relevant parts of the EN 1993 series, or in the relevant material and product specifications.

  • Draft
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1991-1-2:2024(Main)
Eurocode 1 - Actions on structures – Part 1-2: Actions on structures exposed to fire
kSIST FprEN 1991-1-2:2023

1.1   Scope of EN 1991 1 2
(1)   The methods given in this Eurocode are applicable to buildings and civil engineering works, with a fire load related to the building and its occupancy.
(2)   EN 1991 1 2 deals with thermal and mechanical actions on structures exposed to fire. It is intended to be used in conjunction with the fire design Parts of EN 1992 to EN 1996 and EN 1999 which give rules for designing structures for fire resistance.
(3)   EN 1991 1 2 contains thermal actions either nominal or physically based. More data and models for physically based thermal actions are given in annexes.
(4)   EN 1991 1 2 does not cover the assessment of the damage of a structure after a fire.
(5)   EN 1991 1 2 does not cover supplementary requirements concerning, for example:
-   the possible installation and maintenance of sprinkler systems;
-   conditions on occupancy of building or fire compartment;
-   the use of approved insulation and coating materials, including their maintenance.
1.2   Assumptions
(1)   In addition to the general assumptions of EN 1990 the following assumptions apply:
-   any active and passive fire protection systems taken into account in the design will be adequately maintained;
-   the choice of the relevant design fire scenario is made by appropriate qualified and experienced personnel, or is given by the relevant national regulation.

  • Draft
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1993-1-5:2024(Main)
Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements
kSIST FprEN 1993-1-5:2023

1.1   Scope of EN 1993-1-5
(1) This document provides rules for structural design of stiffened and unstiffened nominally flat plates which are subject to in-plane forces.
(2) Non-uniform stress distributions due to shear lag, in-plane load introduction and plate buckling are covered. The effects of out-of-plane loading are outside the scope of this document.
NOTE 1   The rules in this part complement the rules for class 1, 2, 3 and 4 sections, see EN 1993-1-1.
NOTE 2   For the design of slender plates which are subject to repeated direct stress and/or shear and also fatigue due to out-of-plane bending of plate elements ("breathing"), see EN 1993-2 and EN 1993-6.
NOTE 3   For the effects of out-of-plane loading and for the combination of in-plane effects and out-of-plane loading effects, see EN 1993-2 and EN 1993-1-7.
(3) Single plate elements are considered as nominally flat where the curvature radius r in the direction perpendicular to the compression satisfies, as illustrated in Figure 1.1:
r≥b^2/t   (1.1)
where
b   is the panel width;
t   is the plate thickness.
Figure 1.1 - Definition of plate curvature
1.2   Assumptions
(1) Unless specifically stated, EN 1990, the EN 1991 series and EN 1993-1-1 apply.
(2) The design methods given in EN 1993-1-5 are applicable if
-   the execution quality is as specified in EN 1090-2 and
-   the construction materials and products used are as specified in the relevant parts of the EN 1993 series or in the relevant material product specifications.

  • Draft
    73 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1993-1-2:2024(Main)
Eurocode 3 - Design of steel structures - Part 1-2: Structural fire design
kSIST FprEN 1993-1-2:2023

1.1   Scope of prEN 1993-1-2
(1) This document provides rules for the design of steel structures for the accidental situation of fire exposure. This Part of EN 1993 only identifies differences from, or supplements to, normal temperature design.
(2) This document applies to steel structures required to fulfil a loadbearing function.
(3) This document does not include rules for separating function.
(4) This document gives principles and application rules for the design of structures for specified requirements in respect of the aforementioned function and the levels of performance.
(5) This document applies to structures, or parts of structures, that are within the scope of EN 1993 1 1 and are designed accordingly.
(6) This document is intended to be used in conjunction with EN 1991-1-2, EN 1993-1-1, EN 1993 1-3, EN 1993-1-4, EN 1993-1-5, EN 1993-1-6, EN 1993-1-7, EN 1993-1-8, EN 1993-1-11, EN 1993-1-13 or EN 1993-1-14.
1.2   Assumptions
(1) Unless specifically stated, EN 1990, EN 1991(all parts) and EN 1993-1-1 apply.
(2) The design methods given in prEN 1993-1-2 are applicable if
-   the execution quality is as specified in EN 1090-2 and/or EN 1090-4, and
-   the construction materials and products used are as specified in prEN 1993-1-1:2020, Table 5.1 and Table 5.2 and in prEN 1993-1-3:2022, Table 5.1 and Table 5.2, or in the relevant material and product specifications.
(3) In addition to the general assumptions of EN 1990 the following assumptions apply:
-   the choice of the relevant design fire scenario is made by appropriate qualified and experienced personnel, or is given by the relevant national regulation;
-   any fire protection measure taken into account in the design will be adequately maintained.

  • Draft
    91 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1996-3:2023(Main)
Eurocode 6 - Design of masonry structures - Part 3: Simplified calculation methods for unreinforced masonry structures
SIST EN 1996-3:2024

1.1   Scope of EN 1996-3
(1)   This document provides simplified calculation methods to facilitate the design of the following unreinforced masonry walls, subject to certain conditions of application:
-   walls subjected to vertical and wind loading;
-   walls subjected to concentrated loads;
-   shear walls;
-   basement walls subjected to lateral earth pressure and vertical loading;
-   walls subjected to lateral loading but not subjected to vertical loading.
NOTE 1   For those types of masonry structures or parts of structures not covered by (1), the design can be based on EN 1996-1-1.
NOTE 2   The rules given in this document are consistent with those given in EN 1996-1-1 but are more conservative in respect of the conditions and limitations of their use.
(2) This document applies only to those masonry structures, or parts thereof, that are described in EN 1996-1-1 and EN 1996-2.
(3) The simplified calculation methods given in this document do not cover the design of double-leaf walls.
(4) The simplified calculation methods given in this document do not cover the design for accidental situations.
1.2   Assumptions
(1) The assumptions of EN 1990 apply to this document.
(2) This document is intended to be used, for direct application, together with EN 1990, the EN 1991 series, EN 1996 1-1, EN 1996-1-2 and EN 1996-2.
(3) The rules given in this document assume that concrete floors are designed according to EN 1992-1-1.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1992-1-2:2023(Main)
Eurocode 2 - Design of concrete structures – Part 1-2: Structural fire design
SIST EN 1992-1-2:2024

1.1   Scope of prEN 1992 1 2
(1)   This document deals with the design of concrete structures for the accidental situation of fire exposure and is intended to be used in conjunction with prEN 1992 1 1 and EN 1991 1 2. This document identifies differences from, or supplements to, normal temperature design.
(2)   This document applies to concrete structures required to fulfil a loadbearing function, separating function or both.
(3)   This document gives principles and application rules for the design of structures for specified requirements in respect of the aforementioned functions and the levels of performance.
(4)   This document applies to structures, or parts of structures, that are within the scope of prEN 1992 1 1 and are designed accordingly.
(5)   The methods given in this document are applicable to normal weight concrete up to strength class C100/115 and lightweight concrete up to strength class LC50/60.
1.2   Assumptions
(1)   In addition to the general assumptions of prEN 1990 the following assumptions apply:
-   the choice of the relevant design fire scenario is made by appropriate qualified and experienced personnel or is given by the relevant national regulation;
-   any fire protection measure taken into account in the design will be adequately maintained.

  • Standard
    88 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1991-2:2023(Main)
Eurocode 1 - Actions on structures - Part 2: Traffic loads on bridges and other civil engineering works
SIST EN 1991-2:2024

(1)   This document defines imposed loads (models and representative values) associated with road traffic, pedestrian actions and rail traffic which include, when relevant, dynamic effects and centrifugal, braking and acceleration actions and actions for accidental design situations.
(2)   Imposed loads defined in this document are applicable for the design of new bridges, including piers, abutments, upstand walls, wing walls and flank walls, noise barriers, canopies etc., and their foundations. Where appropriate, the loads can also be considered as a basis for assessment or modification of existing structures in combination with complementary conditions if necessary.
(3)   The load models and values given in this document are also applicable for the design of retaining walls adjacent to roads and railway lines and the design of earthworks subject to road or rail traffic actions. This document also provides applicability conditions for specific load models.
(4)   This document is intended to be used with prEN 1990, the other parts of the EN 1991 series and the EN 1992 series to EN 1999 series for the design of structures.

  • Standard
    160 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1992-1-1:2023(Main)
Eurocode 2 - Design of concrete structures - Part 1-1: General rules and rules for buildings, bridges and civil engineering structures
SIST EN 1992-1-1:2024

1.1    Scope of FprEN 1992-1-1
(1)   This document gives the general basis for the design of structures in plain, reinforced and prestressed concrete made with normal weight, lightweight and heavyweight aggregates. It gives specific rules for buildings, bridges and civil engineering structures, including temporary structures; additional requirements specific to bridges are given in Annex K. The rules are valid under temperature conditions between −40 °C and +100 °C generally. This document complies with the principles and requirements for the safety, serviceability, durability and robustness of structures, the basis of their design and verification that are given in EN 1990.
(2)   This document is only concerned with the requirements for resistance, serviceability, durability, robustness and fire resistance of concrete structures. Other requirements, e.g. concerning thermal or sound insulation, are not considered.
(3)    This document does not cover:
-   resistance to fire (see EN 1992 1 2);
-   fastenings in concrete (see EN 1992 4);
-   seismic design (see EN 1998 (all parts));
-   particular aspects of special types of civil engineering works (such as dams, pressure vessels);
-   structures made with no-fines concrete, aerated or cellular concrete, lightweight aggregate concrete with open structure components;
-   structures containing steel sections considered in design (see EN 1994 (all parts)) for composite steel and concrete structures;
-   structural parts made of concrete with a smallest value of the upper sieve aggregate size Dlower < 8 mm (or if known Dmax < 8 mm) unless otherwise stated in this Eurocode.
1.2   Assumptions
(1)   The assumptions of EN 1990 apply to FprEN 1992-1-1.
(2)   It is assumed that the requirements for execution and workmanship given in EN 13670 are complied with.

  • Standard
    402 pages
    English language
    sale 10% off
    e-Library read for
    1 day