EN 848-2:2007+A1:2009

Safety of woodworking machines - One side moulding machines with rotating tool - Part 2: Single spindle hand fed/integrated fed routing machines

This document specifies all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable single spindle hand fed/integrated fed routing machines with fixed head but allowing only movement along the axis of the tool during machining hereinafter referred to as "machines" designed to cut solid wood, chip board, fibreboard, plywood and also these materials if they are covered with plastic laminate, edgings or veneer when they are used as intended and under the conditions foreseen by the manufacturer.
NOTE 1   For the definition of stationary and displaceable machine see 3.2.17 and 3.2.18.
This document does not apply to:
a)   inverted pin routers and radial arm routers (machines where the work piece is fixed and the tool head is manually moved);
b)   NC boring machines and NC routing machines;
NOTE 2   NC boring machines and NC routing machines are dealt with in EN 848-3:2007.
c)   hand-held routers or any adaptation permitting their use in a different mode, e.g. bench mounting;
NOTE 3   Hand-held motor-operated electric tools are dealt with in EN 60745-1:2003 together with EN 60745-2-17:2003.
d)   routing machines set up on a bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of being lifted by one person by hand. The bench can also be an integrated part of the machine if it consists of hinged legs which can be extended down.
NOTE 4   Transportable motor-operated electric tools are dealt with in EN 61029-1:2000 together with
EN 61029-2-8:2003.
This document is not applicable to single spindle hand fed/integrated fed routing machines which are manufactured before the date of its publication as EN.

Sicherheit von Holzbearbeitungsmaschinen - Fräsmaschinen für einseitige Bearbeitung mit drehendem Werkzeug - Teil 2: Einspindelige Oberfräsmaschinen mit Handvorschub/mechanischem Vorschub

Dieses Dokument !spezifiziert alle" im Abschnitt 4 aufgeführten signifikanten Gefährdungen, Gefährdungssituationen
und Gefährdungsereignisse, die auf stationäre und verschiebbare einspindelige Oberfräsmaschinen
mit Handvorschub/mechanischem Vorschub mit feststehendem Werkzeugträger, der aber eine
Bewegung nur in Richtung der Werkzeugachse während der Bearbeitung zulässt, zutreffen — im Folgenden
als „Maschinen“ bezeichnet — , die konstruiert sind zum Bearbeiten von Massivholz, Spanplatten, Faserplatten,
Sperrholz sowie diesen Werkstoffen, wenn sie kunststoffbeschichtet oder mit Kunststoffkanten oder
Furnier versehen sind, wenn sie bestimmungsgemäß und entsprechend den vorhersehbaren Bedingungen
des Herstellers verwendet werden.
ANMERKUNG 1 Hinsichtlich der Definitionen für stationäre und verschiebbare Maschinen siehe 3.2.17 und 3.2.18.
Dieses Dokument gilt nicht für:
a) Kopier-Unterfräsmaschinen und Radialarm-Oberfräsmaschinen (Maschinen bei denen das Werkstück
festliegt und der Werkzeugträger von Hand bewegt wird);
b) NC-Bohrmaschinen und NC-Fräsmaschinen;
ANMERKUNG 2 NC-Bohrmaschinen und NC-Fräsmaschinen sind in EN 848-3:2007 behandelt.
c) handgeführte Oberfräsmaschinen oder irgendwelche Einrichtungen, die ihre Verwendung in einer
anderen Weise, z. B. in einer Stationäreinrichtung, ermöglichen;
ANMERKUNG 3 Handgeführte motorbetriebene Elektrowerkzeuge sind in EN 60745-1:2003 zusammen mit
EN 60745-2-17:2003 behandelt.
d) Oberfräsmaschinen, die auf ein Gestell oder auf einen Tisch, der einem Gestell ähnlich ist, aufgesetzt
sind und die vorgesehen sind, während des Betriebs stationär verwendet zu werden und die von einer
Person von Hand angehoben werden können. Das Gestell kann auch ein fester Teil der Maschine sein,
wenn es aus scharnierbefestigten Füßen besteht, die heruntergeklappt werden können.

Sécurité des machines pour le travail du bois - Machines à fraiser sur une face, à outil rotatif - Partie 2: Défonceuses monobroche à avance manuelle/mécanisée

Le présent document spécifie tous les phénomènes dangereux, situations et événements dangereux significatifs, tels qu’énumérés dans l’Article 4, applicables aux défonceuses monobroche à avance manuelle ou mécanisée, fixes ou transportables, avec une tête fixe, qui ne permet que le mouvement le long de l’axe de l’outil durant l’usinage, et désignées ci-après sous le terme «machines». Celles-ci sont conçues pour usiner du bois, des panneaux de fibres ou de particules, de contre-plaqué, y compris quand la surface ou le chant sont recouverts de plastique, de bordures ou de placage, durant l’utilisation normale et dans les conditions prévues par le fabricant.
NOTE 1   Pour la définition de machine fixe et transportable, voir 3.2.17 et 3.2.18.
Le présent document n'est pas applicable aux :
a)   défonceuses à téton inversé ni aux défonceuses radiales (machines pour lesquelles la pièce est fixe et le porte-outil est déplacé manuellement) ;
b)   perceuses et défonceuses à commande numérique ;
NOTE 2   Les perceuses et défonceuses à commande numérique sont traitées dans l’EN 848-3:2007.
c)   défonceuses portatives ou toute adaptation permettant leur utilisation de manière différente, par exemple fixées sur un bâti ;
NOTE 3   Les outils électroportatifs à moteur sont traités dans l’EN 60745-1:2003 à utiliser conjointement avec l’EN 60745-2-17:2003.
d)   réglages des défonceuses montées sur un bâti ou sur une table similaire à un bâti, conçues pour réaliser un travail à poste fixe et capables d’être soulevées à la main par une personne. Le bâti peut aussi être une partie intégrée à la machine s’il consiste en pieds articulés qui peuvent être dépliés.
NOTE 4   Les machines-outils semi-fixes électriques sont traitées dans l’EN 61029-1:2000 à utiliser conjointement avec l’EN 61029-2-8:2003.
Le présent document n’est pas applicable aux défonceuses monobroche à avance manuelle ou mécanisée fabriquées avant la date de publication comme EN.

Varnost lesnoobdelovalnih strojev - Rezkalniki z vrtilnim orodjem za enostransko obdelavo - 2. del: Enovretenski namizni rezkalni stroji z ročnim/mehanskim podajanjem

Ta dokument opredeljuje vsa velika tveganja, nevarna stanja in dogodke, kot so našteti v določbi št. 4, ki so pomembni za stacionarne in premestljive enovretenske navpične rezkalne stroje z ročnim/mehanskim podajanjem s fiksno glavo, ki dovoljujejo le gibanje vzdolž osi orodja med strojno obdelavo, v nadaljevanju »stroji«, ki so zasnovani za rezanje masivnega lesa, ivernih plošč, plošč iz stisnjenih vlaken, vezanega lesa, kot tudi teh istih materialov, če so prekriti s plastičnim laminatom, robovi ali furnirjem, kadar se uporabljajo v skladu z namembnostjo in pod pogoji, ki jih predvidi proizvajalec.

General Information

• Status: Withdrawn
• Publication Date: 10-Nov-2009
• Withdrawal Date: 25-Sep-2012
• ICS: 79.120.10 - Woodworking machines
• Technical Committee: CEN/TC 142 - Woodworking machines - Safety
• Drafting Committee: CEN/TC 142/WG 5 - Spindle moulding, routing machines and machine centres
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 26-Sep-2012
• Completion Date: 26-Sep-2012
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Directive: 98/37/EC - Machinery
• Mandate: M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: SIST EN 848-2:2007+A1:2010 - Safety of woodworking machines - One side moulding machines with rotating tool - Part 2: Single spindle hand fed/integrated fed routing machines

Relations

• Merged Into: EN 848-2:2007+A2:2012 - Safety of woodworking machines - One side moulding machines with rotating tool - Part 2: Single spindle hand fed/integrated fed routing machines
• Effective Date: 01-Aug-2012
• Merged From: EN 848-2:2007/FprA1 - Safety of woodworking machines - One side moulding machines with rotating tool - Part 2: Single spindle hand fed/integrated fed routing machines
• Effective Date: 19-Jan-2023
• Merged From: EN 848-2:2007 - Safety of woodworking machines - One side moulding machines with rotating tool - Part 2: Single spindle hand fed/integrated fed routing machines
• Effective Date: 12-Sep-2009
• Amended By: EN 848-2:2007+A1:2009/FprA2 - Safety of woodworking machines - One side moulding machines with rotating tool - Part 2: Single spindle hand fed/integrated fed routing machines
• Effective Date: 17-Jul-2010

Standards Content (Sample)

SLOVENSKI STANDARD
01-januar-2010
9DUQRVWOHVQRREGHORYDOQLKVWURMHY5H]NDOQLNL]YUWLOQLPRURGMHP]DHQRVWUDQVNR
REGHODYRGHO(QRYUHWHQVNLQDPL]QLUH]NDOQLVWURML]URþQLPPHKDQVNLP
SRGDMDQMHP
Safety of woodworking machines - One side moulding machines with rotating tool - Part
2: Single spindle hand fed/integrated fed routing machines
Sicherheit von Holzbearbeitungsmaschinen - Fräsmaschinen für einseitige Bearbeitung
mit drehendem Werkzeug - Teil 2: Einspindelige Oberfräsmaschinen mit
Handvorschub/mechanischem Vorschub
Sécurité des machines pour le travail du bois - Machines à fraiser sur une face à outil
rotatif - Partie 2: Défonceuses monobroches à avance manuelle/mécanisée
Ta slovenski standard je istoveten z: EN 848-2:2007+A1:2009
ICS:
79.120.10 Lesnoobdelovalni stroji Woodworking machines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 848-2:2007+A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2009
ICS 79.120.10 Supersedes EN 848-2:2007
English Version
Safety of woodworking machines - One side moulding machines
with rotating tool - Part 2: Single spindle hand fed/integrated fed
routing machines
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
fraiser sur une face à outil rotatif - Partie 2: Défonceuses Fräsmaschinen für einseitige Bearbeitung mit drehendem
monobroches à avance manuelle/mécanisée Werkzeug - Teil 2: Einspindelige Oberfräsmaschinen mit
Handvorschub/mechanischem Vorschub
This European Standard was approved by CEN on 13 January 2007 and includes Amendment 1 approved by CEN on 3 October 2009.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 848-2:2007+A1:2009: E
worldwide for CEN national Members.

Contents Page
Foreword .4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms and definitions .8
3.1 General .8
3.2 Definitions .8
3.3 Terms . 14
4 List of significant hazards . 15
5 Safety requirements and/or measures . 19
5.1 General . 19
5.2 Controls . 19
5.2.1 Safety and reliability of control systems . 19
5.2.2 Position of controls . 20
5.2.3 Starting . 21
5.2.4 Normal stopping . 22
5.2.5 Additional stop . 22
5.2.6 Emergency stop . 23
5.2.7 Mode selection . 23
5.2.8 Spindle speed monitoring . 24
5.2.9 Integrated feed . 25
5.2.10 Failure of the power supply . 25
5.2.11 Failure of the control circuits . 25
5.3 Protection against mechanical hazards . 25
5.3.1 Stability . 25
5.3.2 Hazard of break up during operation . 26
5.3.3 Tool holder and tool design . 26
5.3.4 Braking . 28
5.3.5 Devices to minimise the possibility or the effect of ejection . 29
5.3.6 Workpiece supports and guides . 31
5.3.7 Prevention of access to moving parts . 33
5.3.8 Characteristics of guards and safety devices . 35
5.3.9 Clamping device . 35
5.3.10 Safety appliances. 35
5.4 Protection against non mechanical hazards . 36
5.4.1 Fire . 36
5.4.2 Noise . 36
5.4.3 Emission of chips and dust . 37
5.4.4 Electricity . 37
5.4.5 Ergonomics and handling . 38
5.4.6 Pneumatics . 39
5.4.7 Hydraulics . 39
5.4.8 Electromagnetic compatibility . 39
5.4.9 Static electricity . 39
5.4.10 Errors of fitting . 39
5.4.11 Supply disconnecting devices . 39
5.4.12 Maintenance . 40
6 Information for use . 40
6.1 Warning devices . 40
6.2 Marking . 40
6.3 Instruction handbook . 41
Annex A (informative) Use of well tried components . 46
Annex B (normative) Stability test for displaceable machines . 47
Annex C (normative) Braking tests . 48
C.1 Conditions for all tests . 48
C.2.1 Un-braked run-down time . 48
C.2.2 Braked run-down time . 48
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC . 49
Annex ZB (informative) !Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC" . 52
Bibliography . 56

Foreword
This document (EN 848-2:2007+A1:2009) has been prepared by Technical Committee CEN/TC 142
“Woodworking machines - Safety”, the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2010, and conflicting national standards shall be withdrawn at the
latest by May 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document includes Amendment 1, approved by CEN on 2009-10-03.
This document supersedes !EN 848-2:2007".
The start and finish of text introduced or altered by amendment is indicated in the text by tags!"͘
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of the !Machinery Directives".
!For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document."
Organisation contributing to the preparation of this document include the European Association of
Manufacturer of Woodworking Machines "EUMABOIS".
The European Standards produced by CEN/TC 142 are particular to woodworking machines and compliment
the relevant A and B standards on the subject of general safety (see introduction of EN ISO 12100-1:2003 for
a description of A, B and C standards).
!EN 848 Safety of woodworking machines — One side moulding machines with rotating tool consists of the
following parts:
Part 1: Single spindle vertical moulding machines
Part 2: Single spindle hand fed/integrated fed routing machines
Part 3: Numerically controlled (NC) boring and routing machines"
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound
...