EN ISO 5263-3:2004

Pulps - Laboratory wet disintegration - Part 3: Disintegration of mechanical pulps at > 85 degrees C (ISO 5263-3:2004)

ISO 5263-3:2004 specifies an apparatus and the procedures for the laboratory wet disintegration of mechanical pulps that exhibit latency. This apparatus and procedure are required for preparation of the test portion in a number of other International Standards dealing with pulps.
ISO 5263-3:2004 is applicable to all kind of mechanical pulps (i.e. mechanical, semi-chemical and chemo-mechanical pulps) exhibiting latency. Mechanical pulps not exhibiting latency shall be disintegrated according to ISO 5263-2.
The procedure specified in ISO 5263-2 should be used to disintegrate all mechanical pulps to be measured for brightness.

Faserstoffe - Nassaufschlagen im Labor - Teil 3: Aufschlagen von Holzstoff bei >85 grad C (ISO 5263-3:2004)

Dieser Teil der ISO 5263 legt ein Laborgerät und Verfahren zum Nassaufschlagen von Holzstoffen im Labor mit Latenz fest. Das Gerät und das Verfahren finden auch zur Probenvorbereitung in mehreren anderen Internationalen Normen zum Thema Faserstoffe Anwendung.
ISO 5263-3 ist für alle Holzstoffarten (d. h. Holzstoffe, Halbzellstoffe und chemische Holzstoffe) mit Latenz anwendbar. Die Holzstoffe müssen nach ISO 5263-2 aufgeschlagen werden.
Das in ISO 5263-2 festgelegte Verfahren sollte auch zum Aufschlagen all der Holzstoffarten verwendet werden, die auf den Weißgrad untersucht werden.
ANMERKUNG   Der Weißgrad wird durch das Vorhandensein von Latenz nicht signifikant beeinflusst; bei der Heißzerfaserung  von Holzstoffen kann es jedoch zu signifikanten Weißgradverlusten kommen.

Pâtes - Désintégration humide en laboratoire - Partie 3: Désintégration des pâtes mécaniques à > 85 degrés C (ISO 5263-3:2004)

Vlaknine - Laboratorijsko razvlaknjevanje v mokrem - 3. del: Razvlaknjevanje mehanskih vlaknin pri > 85 stopinjah C (ISO 5263-3:2004)

General Information

• Status: Withdrawn
• Publication Date: 31-Aug-2004
• Withdrawal Date: 21-Feb-2023
• ICS: 85.040 - Pulps
• Technical Committee: CEN/TC 172 - Pulp, paper and board
• Drafting Committee: CEN/TC 172 - Pulp, paper and board
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 22-Feb-2023
• Ref Project: SIST EN ISO 5263-3:2005 - Pulps - Laboratory wet disintegration - Part 3: Disintegration of mechanical pulps at > 85 degrees C (ISO 5263-3:2004)

Relations

• Replaces: EN ISO 5263:1997 - Pulps - Laboratory wet disintegration (ISO 5263:1995)
• Effective Date: 22-Dec-2008
• Replaced By: EN ISO 5263-3:2023 - Pulps - Laboratory wet disintegration - Part 3: Disintegration of mechanical pulps at ≥ 85°C (ISO 5263-3:2023)
• Effective Date: 19-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 5263-3:2005
01-februar-2005
1DGRPHãþD
SIST EN ISO 5263:2000
Vlaknine - Laboratorijsko razvlaknjevanje v mokrem - 3. del: Razvlaknjevanje
mehanskih vlaknin pri > 85 stopinjah C (ISO 5263-3:2004)
Pulps - Laboratory wet disintegration - Part 3: Disintegration of mechanical pulps at > 85
degrees C (ISO 5263-3:2004)
Faserstoffe - Nassaufschlagen im Labor - Teil 3: Aufschlagen von Holzstoff bei >85 grad
C (ISO 5263-3:2004)
Pâtes - Désintégration humide en laboratoire - Partie 3: Désintégration des pâtes
mécaniques a > 85 degrés C (ISO 5263-3:2004)
Ta slovenski standard je istoveten z: EN ISO 5263-3:2004
ICS:
85.040 Vlaknine Pulps
SIST EN ISO 5263-3:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 5263-3:2005

---------------------- Page: 2 ----------------------

SIST EN ISO 5263-3:2005
EUROPEAN STANDARD
EN ISO 5263-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2004
ICS 85.040 Supersedes EN ISO 5263:1997
English version
Pulps - Laboratory wet disintegration - Part 3: Disintegration of
mechanical pulps at > 85 degrees C (ISO 5263-3:2004)
Pâtes - Désintégration humide en laboratoire - Partie 3:
Désintégration des pâtes mécaniques à > 85 degrés C
(ISO 5263-3:2004)
This European Standard was approved by CEN on 2 August 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5263-3:2004: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 5263-3:2005
EN ISO 5263-3:2004 (E)


Foreword

This document (EN ISO 5263-3:2004) has been prepared by Technical Committee ISO/TC 6
"Paper, board and pulps" in collaboration with Technical Committee CEN/TC 172 "Pulp, paper
and board", the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by March 2005, and conflicting national
standards shall be withdrawn at the latest by March 2005.

This document supersedes EN ISO 5263 :1997.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice

The text of ISO 5263-3:2004 has been approved by CEN as EN ISO 5263-3:2004 without any
modifications.
2

---------------------- Page: 4 ----------------------

SIST EN ISO 5263-3:2005


INTERNATIONAL ISO
STANDARD 5263-3
First edition
2004-09-01


Pulps — Laboratory wet disintegration —
Part 3:
Disintegration of mechanical pulps at
WWWW 85 °C
Pâtes — Désintégration humide en laboratoire —
Partie 3: Désintégration des pâtes mécaniques à W 85 °C




Reference number
ISO 5263-3:2004(E)
©
ISO 2004

---------------------- Page: 5 ----------------------

SIST EN ISO 5263-3:2005
ISO 5263-3:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF fi
...