EN ISO 8130-1:2019

Coating powders - Part 1: Determination of particle size distribution by sieving (ISO 8130-1:2019)

This document specifies a method for the determination of the particle size distribution of coating powders by sieve analysis. Particle size distributions with a maximum of less than 100 µm is determined by laser diffraction, ISO 8130‑13. This method is used especially for determining the oversize material or for the presence of contamination and can be used as a quality control procedure ("go"/"no go" test) by checking the amount  retained on a single sieve.
The following particle sizes are typical for coating powders, however the particle size can deviate depending on the application:
—                                 thin-film technology: 1 µm to 63 µm;
—                                 electrostatic coating: 10 µm to 200 µm;
—                                 fluidizing-bed method: 100 µm and above.
NOTE       Sieves with a mesh size smaller than 32 µm are not practical and are likely to become blind during use.

Pulverlacke - Teil 1: Bestimmung der Teilchengrößenverteilung durch Sieben (ISO 8130-1:2019)

Dieses Dokument legt ein Verfahren zum Bestimmen der Partikelgrößenverteilung von Pulverlacken durch Siebanalyse fest. Partikelgrößenverteilungen mit einem Maximum unter 100 μm werden per Laserbeugung, ISO 8130 13, bestimmt. Dieses Verfahren eignet sich vor allem für die Bestimmung des Überkorns oder von Verunreinigungen und kann auch für die Qualitätskontrolle („Ja/Nein-Prüfung“) angewendet werden, d. h. durch Bestimmen des Rückstandes auf nur einem einzigen Sieb.
Folgende Partikelgrößen sind für die verschiedenen Anwendungen von Pulverlacken typisch, auch wenn die Partikelgrößenverteilung je nach Anwendung abweichen kann:
   Dünnschichttechnologie:   1 μm bis 63 μm;
   Elektrostatisches Beschichten:   10 μm bis 200 μm;
   Fluidisierbettverfahren:   100 μm und größer.
ANMERKUNG   Siebe mit einer Maschenweite unter 32 μm sind unpraktisch

Poudres pour revêtement - Partie 1: Détermination de la distribution granulométrique par tamisage (ISO 8130-1:2019)

Le présent document spécifie une méthode de détermination de la distribution granulométrique de poudres pour revêtement au moyen d'une analyse par tamisage. Les distributions granulométriques inférieures à 100 µm, au maximum, sont déterminées par diffraction laser, voir l'ISO 8130-13. La présente méthode est utilisée en particulier pour la détermination du refus ou de la présence de contamination, et peut être utilisée comme mode opératoire de contrôle de la qualité (essai «tout ou rien») en vérifiant la quantité retenue sur un seul tamis.
Les tailles de particules suivantes sont celles rencontrées habituellement dans les poudres pour revêtement, ces valeurs peuvent toutefois varier en fonction de l'application considérée:
—                                 technologie en couches minces: 1 µm à 63 µm;
—                                 revêtement électrostatique: 10 µm à 200 µm;
—                                 méthode par lit fluidisé: 100 µm et au-delà.
NOTE       Les tamis présentant une dimension de mailles inférieure à 32 µm ne sont pas pratiques et sont susceptibles de s'obturer au cours de leur utilisation.

Praškasti premazi - 1. del: Določevanje porazdelitve velikosti delcev s sejanjem (ISO 8130-1:2019)

Ta dokument določa metodo za ugotavljanje porazdelitve velikosti delcev praškastih premazov s sejalno analizo. Porazdelitev velikosti delcev, kjer najvišja velikost ne presega 100 μm, se določa z lasersko difrakcijo, standard ISO 8130-13. Ta metoda se uporablja zlasti za določanje prevelikega materiala ali onesnaženosti ter jo je mogoče uporabljati kot postopek za nadzor kakovosti (preskus »ustreznosti«/»neustreznosti«) s preverjanjem količine, ki ostane na situ.
Naslednje velikosti delcev so običajne za praškaste premaze, vendar pa lahko velikost delcev odstopa v odvisnosti od nanosa:
– tehnologija s tankim filmom: od 1 μm do 63 μm,
– elektrostatična prevleka: od 10 μm do 200 μm,
– metoda fluidizirane plasti: 100 μm in več.
OPOMBA: Sita z velikostjo mreže, manjšo od 32 μm, niso praktična in se med uporabo rada zamašijo.

General Information

• Status: Published
• Publication Date: 07-May-2019
• Withdrawal Date: 29-Nov-2019
• ICS: 87.040 - Paints and varnishes
• Technical Committee: CEN/TC 139 - Paints and varnishes
• Drafting Committee: CEN/TC 139 - Paints and varnishes
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 08-May-2019
• Completion Date: 08-May-2019
• Ref Project: SIST EN ISO 8130-1:2019 - Coating powders - Part 1: Determination of particle size distribution by sieving (ISO 8130-1:2019)

Relations

• Replaces: EN ISO 8130-1:2010 - Coating powders - Part 1: Determination of particle size distribution by sieving (ISO 8130-1:1992)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 8130-1:2019
01-julij-2019
Nadomešča:
SIST EN ISO 8130-1:2012
Praškasti premazi - 1. del: Določevanje porazdelitve velikosti delcev s sejanjem
(ISO 8130-1:2019)
Coating powders - Part 1: Determination of particle size distribution by sieving (ISO 8130
-1:2019)
Pulverlacke - Teil 1: Bestimmung der Teilchengrößenverteilung durch Sieben (ISO 8130-
1:2019)
Poudres pour revêtement - Partie 1: Détermination de la distribution granulométrique par
tamisage (ISO 8130-1:2019)
Ta slovenski standard je istoveten z: EN ISO 8130-1:2019
ICS:
87.040 Barve in laki Paints and varnishes
SIST EN ISO 8130-1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 8130-1:2019

---------------------- Page: 2 ----------------------

SIST EN ISO 8130-1:2019


EN ISO 8130-1
EUROPEAN STANDARD

NORME EUROPÉENNE

May 2019
EUROPÄISCHE NORM
ICS 87.040 Supersedes EN ISO 8130-1:2010
English Version

Coating powders - Part 1: Determination of particle size
distribution by sieving (ISO 8130-1:2019)
Poudres pour revêtement - Partie 1: Détermination de Pulverlacke - Teil 1: Bestimmung der
la distribution granulométrique par tamisage (ISO Teilchengrößenverteilung durch Sieben (ISO 8130-
8130-1:2019) 1:2019)
This European Standard was approved by CEN on 8 March 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8130-1:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 8130-1:2019
EN ISO 8130-1:2019 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 8130-1:2019
EN ISO 8130-1:2019 (E)
European foreword
This document (EN ISO 8130-1:2019) has been prepared by Technical Committee ISO/TC 35 "Paints
and varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2019, and conflicting national standards
shall be withdrawn at the latest by November 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8130-1:2010.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 8130-1:2019 has been approved by CEN as EN ISO 8130-1:2019 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 8130-1:2019

---------------------- Page: 6 ----------------------

SIST EN ISO 8130-1:2019
INTERNATIONAL ISO
STANDARD 8130-1
Second edition
2019-04
Coating powders —
Part 1:
Determination of particle size
distribution by sieving
Poudres po
...