Test sieves — Technical requirements and testing — Part 2: Test sieves of perforated metal plate

ISO 3310-2:2013 specifies the technical requirements and corresponding test methods for test sieves of perforated metal plate. It applies to test sieves having round holes, with sizes from 125 mm down to 1 mm, or square holes, with sizes from 125 mm down to 4 mm, in accordance with ISO 565.

Tamis de contrôle — Exigences techniques et vérifications — Partie 2: Tamis de contrôle en tôles métalliques perforées

La présente partie de l'ISO 3310 spécifie les exigences techniques et les méthodes d'essai correspondantes pour les tamis de contrôle en tôles métalliques perforées. Elle s'applique aux tamis de contrôle ayant — des trous ronds, d'une dimension allant de 125 mm à 1 mm, ou — des trous carrés, d'une dimension allant de 125 mm à 4 mm, conformément à l'ISO 565.

Preskusna sita - Tehnične zahteve in preskušanje - 2. del: Preskusna sita iz kovinskih perforiranih plošč

Ta del standarda ISO 3310 določa tehnične zahteve in ustrezne preskusne metode za preskusna sita iz kovinskih perforiranih plošč.
Uporablja se za preskusna sita z
– okroglimi odprtinami velikosti od 125 mm do 1 mm ali
– kvadratnimi odprtinami velikosti od 125 mm do 4 mm
v skladu s standardom ISO 565.

General Information

Status
Published
Publication Date
12-Aug-2013
Current Stage
9020 - International Standard under periodical review
Start Date
15-Jan-2024
Completion Date
15-Jan-2024

Relations

Buy Standard

Standard
ISO 3310-2:2015
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 3310-2:2013 - Test sieves -- Technical requirements and testing
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 3310-2:2013 - Tamis de contrôle -- Exigences techniques et vérifications
French language
9 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO 3310-2:2015
01-marec-2015
1DGRPHãþD
SIST ISO 3310-2:2002
3UHVNXVQDVLWD7HKQLþQH]DKWHYHLQSUHVNXãDQMHGHO3UHVNXVQDVLWDL]
NRYLQVNLKSHUIRULUDQLKSORãþ
Test sieves - Technical requirements and testing - Part 2: Test sieves of perforated metal
plate
Tamis de contrôle - Exigences techniques et vérifications - Partie 2: Tamis de contrôle
en tôles métalliques perforées
Ta slovenski standard je istoveten z: ISO 3310-2:2013
ICS:
19.120 Analiza velikosti delcev. Particle size analysis. Sieving
Sejanje
SIST ISO 3310-2:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 3310-2:2015

---------------------- Page: 2 ----------------------

SIST ISO 3310-2:2015
INTERNATIONAL ISO
STANDARD 3310-2
Fifth edition
2013-09-01
Test sieves — Technical requirements
and testing —
Part 2:
Test sieves of perforated metal plate
Tamis de contrôle — Exigences techniques et vérifications —
Partie 2: Tamis de contrôle en tôles métalliques perforées
Reference number
ISO 3310-2:2013(E)
©
ISO 2013

---------------------- Page: 3 ----------------------

SIST ISO 3310-2:2015
ISO 3310-2:2013(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 3310-2:2015
ISO 3310-2:2013(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Designation . 1
5 Perforated metal plate . 1
5.1 Requirements . 1
5.2 Test methods . 5
5.3 Documentation for sieve conformity . 6
6 Test sieve frames . 6
7 Marking of test sieves . 7
Annex A (informative) Test sieve record card . 8
Bibliography .
...

INTERNATIONAL ISO
STANDARD 3310-2
Fifth edition
2013-09-01
Test sieves — Technical requirements
and testing —
Part 2:
Test sieves of perforated metal plate
Tamis de contrôle — Exigences techniques et vérifications —
Partie 2: Tamis de contrôle en tôles métalliques perforées
Reference number
ISO 3310-2:2013(E)
©
ISO 2013

---------------------- Page: 1 ----------------------
ISO 3310-2:2013(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3310-2:2013(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Designation . 1
5 Perforated metal plate . 1
5.1 Requirements . 1
5.2 Test methods . 5
5.3 Documentation for sieve conformity . 6
6 Test sieve frames . 6
7 Marking of test sieves . 7
Annex A (informative) Test sieve record card . 8
Bibliography . 9
© ISO 2013 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 3310-2:2013(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further main
...

NORME ISO
INTERNATIONALE 3310-2
Cinquième édition
2013-09-01
Tamis de contrôle — Exigences
techniques et vérifications —
Partie 2:
Tamis de contrôle en tôles métalliques
perforées
Test sieves — Technical requirements and testing —
Part 2: Test sieves of perforated metal plate
Numéro de référence
ISO 3310-2:2013(F)
©
ISO 2013

---------------------- Page: 1 ----------------------
ISO 3310-2:2013(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2013
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2013 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 3310-2:2013(F)

Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Désignation . 1
5 Tôle métallique perforée . 1
5.1 Exigences . 1
5.1.1 Tolérances sur les tailles des trous individuels . 1
5.1.2 Entraxe, p . 2
5.1.3 Épaisseur de tôle . 3
5.1.4 Agencement des trous . 4
5.1.5 Matériau de la tôle . 4
5.2 Méthodes d’essai . 5
5.3 Documentation relative à la conformité des tamis . 6
5.3.1 Fiche de suivi de tamis de contrôle . 6
5.3.2 Certificats . 6
6 Châssis de tamis de contrôle . 6
7 Marquage des tamis de contrôle . 7
Annexe A (i
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.