iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1870-10:2003/prA1

(Amendment)

Safety of woodworking machines - Circular sawing machines - Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines

Safety of woodworking machines - Circular sawing machines - Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines

Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen - Teil 10: Von unten schneidende automatische und halbautomatische Kappsägemaschinen mit einem Sägeblatt (Untertischkappkreissägemaschinen)

Sécurité des machines pour le travail du bois - Machines à scier circulaires - Partie 10: Tronçonneuses monolames automatiques et semi-automatiques à coupe ascendante

Varnost lesnoobdelovalnih strojev - Krožne žage - 10. del: Enojne zajeralne avtomatske in polavtomatske žage za prečni prerez

General Information

Status
Not Published
ICS
79.120.10 - Woodworking machines
Technical Committee
CEN/TC 142 - Woodworking machines - Safety
Drafting Committee
CEN/TC 142/WG 4 - Circular sawing machines
Current Stage
5060 - Closure of Vote - Formal Approval
Start Date
05-Jul-2009
Completion Date
05-Jul-2009
Directive
2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
98/37/EC - Machinery
Mandate
M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
Ref Project
SIST EN 1870-10:2004/kprA1:2009 - Safety of woodworking machines - Circular sawing machines - Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines

Relations

Merged Into
EN 1870-10:2003+A1:2009 - Safety of woodworking machines - Circular sawing machines - Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines
Effective Date
11-Jul-2009
Amends
EN 1870-10:2003 - Safety of woodworking machines - Circular sawing machines - Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines
Effective Date
22-Dec-2008

Buy Standard

EN 1870-10:2004/kprA1:2009EN 1870-10:2004/kprA1:2009
PreviousNext
Draft
EN 1870-10:2004/kprA1:2009
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-maj-2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY.URåQHåDJHGHO(QRMQH]DMHUDOQH
DYWRPDWVNHLQSRODYWRPDWVNHåDJH]DSUHþQLSUHUH]
Safety of woodworking machines - Circular sawing machines - Part 10: Single blade
automatic and semi-automatic up-cutting cross-cut sawing machines
Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen - Teil 10: Von unten
schneidende automatische und halbautomatische Kappsägemaschinen mit einem
Sägeblatt (Untertischkappkreissägemaschinen)
Sécurité des machines pour le travail du bois - Machines à scier circulaires - Partie 10:
Tronçonneuses monolames automatiques et semi-automatiques à coupe ascendante
Ta slovenski standard je istoveten z: EN 1870-10:2003/prA1
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 1870-10:2003
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
February 2009
ICS 79.120.10
English Version
Safety of woodworking machines - Circular sawing machines -
Part 10: Single blade automatic and semi-automatic up-cutting
cross-cut sawing machines
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
scier circulaires - Partie 10: Tronçonneuses monolames Kreissägemaschinen - Teil 10: Von unten schneidende
automatiques et semi-automatiques à coupe ascendante automatische und halbauttomatische Kappsägemaschinen
mit einem Sägeblatt (Untertischkappkreissägemaschinen)
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A1, if approved, will modify the European Standard EN 1870-10:2003. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1870-10:2003/prA1:2009: E
worldwide for CEN national Members.

Contents Page
Foreword .3
1 Modification to the Foreword .4
2 Modification to Clause 1, Scope .4
3 Modification to Clause 2, Normative references .4
4 Modification to Clause 3, Terms and definitions .6
5 Modification to Clause 4, List of hazards .6
6 Modification to Clause 5, Safety requirements and/or measures (hanging paragraphs) .8
7 Modification to 5.1.1, Safety and reliability of control systems .8
8 Modification to 5.1.2, Position of controls .9
9 Modification to 5.1.3, Starting .9
10 Modification to 5.1.4, Normal stopping .9
11 Modification to 5.1.5, Emergency stop .9
12 Modification to 5.1.8, Failure of the power supply .9
13 Modification to 5.1.9, Failure of the control circuits .9
14 Modification to 5.2.1, Stability .9
15 Modification to 5.2.2, Risk of break-up during operation .9
16 Modification to 5.2.3.1, Spindle locking. 10
17 Modification to 5.2.6.3, Workpiece guides . 10
18 Modification to 5.3.1, Fire . 10
19 Modification to 5.3.4, Electricity . 10
20 Modification to 5.3.5, Ergonomics and handling . 10
21 Modification to 5.3.8, Radiation . 11
22 Modification to 5.3.9, Laser . 11
23 Modification to 5.3.12, Isolation . 12
24 Modification to 5.3.13, Maintenance . 12
25 Modification to 6.2, Marking . 12
26 Modification to 6.3, Instruction handbook . 12
27 Modification to Annex B . 14
28 Modification to Annex ZA, Relationship between this European Standard and the
Essential Requirements of EU Directive 98/37/EC . 14
29 Addition of Annex ZB, Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC . 15
30 Modification to the Bibliography . 15

Foreword
This document (EN 1870-10:2003/prA1:2009) has been prepared by Technical Committee CEN/TC 142
“Woodworking machines - Safety”, the secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of the Machinery Directive.
For relationship with EU Directive, see informative Annexes ZA and ZB, which are integral parts of this
document.
1 Modification to the Foreword
Replace the fourth paragraph with the following:
"For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.".
th
In the 6 paragraph, replace "annex B is informative" with "Annexes ZA and ZB are informative".

2 Modification to Clause 1, Scope
Replace the first paragraph with: "This document deals with the significant hazards, hazardous situations and
events as listed in Clause 4 which are relevant to single blade automatic and semi-automatic up-cutting cross
cut sawing machines with one sawing unit herein after referred to as ‘machines’ designed to cut solid wood,
chipboard, fibreboard, plywood and also these materials when they are covered with plastic edging and/or
plastic/light alloy laminates."
Delete the third paragraph.
3 Modification to Clause 2, Normative references
Replace the standard paragraph with the following: "The following referenced documents are indispensable
for the application of this document. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.".
Delete reference EN 292-1:1991 in Clause 2 and replace "EN 292-1:1991" with "EN ISO 12100-1:2003"
throughout the document.
Delete references EN 292-2:1991 and EN 292/A1:1995.
Delete reference EN 294:1992 and replace it with "EN ISO 13857:2008, Safety of machinery - Safety
distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)". Replace "EN
294:1992" with "EN ISO 13857:2008" throughout the document.
Delete reference to EN 418:1992, replace it with "EN ISO 13850, Safety of machinery — Emergency stop —
st
Principles for design (ISO 13850:2006)" and replace "EN 418:1992" in 5.1.5, 1 paragraph, with
"EN ISO 13850".
Replace "EN 847-1:1997" with "EN 847-1:2005" throughout the document and in the title replace "and"
between "tools" and "circular" with a comma.
Delete reference EN 954-1:1996 and replace it with "EN ISO 13849-1:2008, Safety of machinery - Safety-
related parts of control systems - Part 1: General principles for design (ISO 13849-1:2006)". Replace "EN 954-
1:1996" with "EN ISO 13849-1:2008" throughout the document.
Delete reference to "EN 1070:1998" and replace it with "EN ISO 12100-1:2003" throughout the document.
Replace reference to "EN 60204-1:1992" with "EN 60204-1:2006, Safety of machinery - Electrical equipment
of machines - Part 1: General requirements (IEC 60204-1:2005, modified)".
Replace reference to "EN 60825-1:1994+ A11:1996 + A2:2001" with "EN 60825-1:2007, Safety of laser
products — Part 1: Equipment classification and requirements (IEC 60825-1:2007)".
Replace "EN 60947-4-1:1992" with "EN 60947-4-1:2001" throughout the document and replace in the title
"(IEC 60947-4-1:1990)" with "(IEC 60947-4-1:2000)".
Replace "EN 60947-5-1:1997" with "EN 60947-5-1:2004" throughout the document and replace in the title
"(IEC 60947-5-1:1997)" with "(IEC 60947-5-1:2003)".
Replace "prEN 61496-2:1997" with "CLC/TS 61496-2:2006" in Clause 2 and "prEN 61496-2:1997" with
rd
"CLC/TS 61496-2:2006" throughout the document and the 3 element of the title with "Part 2: Particular
requirements for equipment using active opto-electronic protective devices (AOPDs) (IEC 61496-2:2006)".
Delete reference to "ISO 3745:1997", replace it with "EN ISO 3745:2003, Acoustics — Determination of sound
power levels of noise sources using sound pressure — Precision methods for anechoic and semi-anechoic
rooms (ISO 3745:2003)" and replace "ISO 3745:1997" with "EN ISO 3745:2003" throughout the document.
Replace reference to "HD 21.1 S3:1997" with "HD 21.1 S4:2002, Cables of rated voltages up to and including
450/750 V and having thermoplastic insulation — Part 1: General requirements" and replace "HD 21.1
S3:1997" with "HD 21.1 S4:2002" throughout the document.
Replace reference to "HD 22.1 S3:1997" with "HD 22.1 S4:2002, Cables of rated voltages up to and including
450/750 V and having cross-linked insulation — Part 1: General requirements" and replace "HD 22.1
S3:1997" with "HD 22.1 S4:2002" throughout the document.
Replace reference to "HD 22.4 S3:1995+ A1:1999" with "HD 22.4 S4:2004, Cables of rated voltages up to and
including 450/750 V and having crosslinked insulation — Part 4: Cords and flexible cables" and replace "HD
22.4 S3:1995+ A1:1999" with "HD 22.4 S4:2004" throughout the document.
Add the following references:
"EN 894-1:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 1: General principles for human interactions with displays and control actuators
EN 894-2:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 2: Displays
EN 894-3:2000, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 3: Control actuators",
"EN 1005-1:2001, Safety of machinery — Human physical performance — Part 1: Terms and definitions
EN 1005-2:2003, Safety of machinery — Human physical performance — Part 2: Manual handling of
machinery and component parts of machinery
EN 1005-3:2002, Safety of machinery — Human physical performance — Part 3: Recommended force limits
for machinery operation
EN 1005-4:2005, Safety of machinery — Human physical performance — Part 4: Evaluation of working
postures and movements in relation to machinery"
"EN 50370-1:2005, Electromagnetic compatibility (EMC) — Product family standard for machine-tools —
Part 1: Emission
EN 50370-2:2003, Electromagnetic compatibility (EMC) — Product family standard for machine-tools —
Part 2: Immunity",
"EN 60439-1:1999, Low-voltage switchgear and controlgear assemblies — Part 1: Type-tested and partially
type-tested assemblies (IEC 60439-1:1999)",
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 19085-4:2024(Main)
Woodworking machines - Safety - Part 4: Vertical panel circular sawing machines (ISO 19085-4:2024)
SIST EN ISO 19085-4:2025

This document specifies the safety requirements and measures for manually loaded and unloaded vertical panel circular sawing machines (defined in 3.1) capable of continuous production use, with hand feed or integrated feed, hereinafter referred to also as “machines”.
This document deals with all significant hazards, hazardous situations and events, as listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer, including reasonably foreseeable misuse. Transport, assembly, dismantling, disabling and scrapping phases are also taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
—     an integrated feed device;
—     a device for scoring;
—     an angle cutting device;
—     a middle support device;
—     programmable end stops for parallel vertical cuts;
—     a device for grooving with a milling tool with a cutting width not exceeding 27 mm;
—     a panel pusher;
—     a panel lowering device;
—     stop devices for workpiece during horizontal cuts.
The machines are designed for cutting panels consisting of:
a)       solid wood;
b)       material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2);
c)        composite materials with core consisting, for example, of polyurethane or mineral material laminated with light alloy;
d)       polymer-matrix composite materials and reinforced thermoplastic/thermoset/elastomeric materials;
e)       gypsum boards, gypsum bounded fibreboards;
f)         honeycomb aluminium boards;
g)       matrix engineered mineral boards, silicate boards;
h)       aluminium light alloy plates;
i)         composite boards made from the materials listed above.
This document does not apply to machines
—     with pressure beam and saw unit mounted behind the workpiece support,
—     where the guide rails on which the saw unit moves vertically are fixed on the machine frame and the horizontal cut can only be made by manually feeding the panel,
—     designed to cut in vertical direction only,
—     automatically performing two or more cutting cycles in sequence,
—     intended for use in potentially explosive atmosphere, and
—     manufactured prior to the publication of this document.

  • Draft
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-9:2024(Main)
Woodworking machines - Safety - Part 9: Circular saw benches (with and without sliding table) (ISO 19085-9:2024)
SIST EN ISO 19085-9:2025

This document specifies the safety requirements and measures for circular saw benches with or without sliding table or demountable power feed unit or both and capable of continuous production use, also known as “table saws” (in the USA), hereinafter referred to also as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2).
This document deals with all significant hazards, hazardous situations and events as listed in Annex A relevant to the machines when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to machines fitted with one or more of the following devices or working units, whose hazards have been dealt with:
—     device for the main saw blade and scoring saw blade to be raised and lowered through the table;
—     device to tilt the main saw blade and scoring saw blade for angled cutting;
—     device for scoring;
—     device for grooving with milling tool with a width not exceeding 20 mm in one pass;
—     demountable power feed unit;
—     additional manually operated sliding table;
—     powered workpiece clamping device.
This document does not apply to:
a)       machines intended for outdoor use on building sites;
NOTE            Building site saws (contractor saws) are covered by the requirements of ISO 19085-10:2018.
b)       handheld woodworking machines including any adaptation permitting their use in a different mode, i.e. bench mounting;
c)        machines intended for use in a potentially explosive atmosphere;
d)       machines manufactured prior to the publication of this document.

  • Draft
    59 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-5:2024(Main)
Woodworking machines - Safety - Part 5: Dimension saws (ISO 19085-5:2024)
SIST EN ISO 19085-5:2025

This document specifies the safety requirements and measures for dimension saws (defined in 3.1), capable of continuous production use and hereinafter referred to also as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood.
This document deals with all significant hazards, hazardous situations and events, listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
a)       device to raise and lower the main saw blade and scoring saw blade;
b)       device to tilt the main saw blade and scoring saw blade for angled cutting in one or both directions;
c)        device for scoring;
d)       device for grooving with milling tool with a width not exceeding 20 mm;
e)       demountable power feed unit;
f)         power-operated sliding table;
g)       workpiece clamping.
This document is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

  • Draft
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-7:2024(Main)
Woodworking machines - Safety - Part 7: Surface planing, thickness planing and combined surface/thickness planing machines (ISO 19085-7:2024)
SIST EN ISO 19085-7:2024

This document specifies the safety requirements and measures for
—     surface planing machines, also called jointers,
—     thickness planing machines, also called planers or single surface planers, and
—     combined surface/thickness planing machines
with fixed cutter block position, with an integrated feed in thickness planing mode, with or without demountable power feed device in planing mode, with manual loading and/or unloading of the workpiece, and capable of continuous production use, altogether referred to as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2).
This document deals with all significant hazards, hazardous situations and events as listed in Annex A relevant to the machines when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer. Reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to surface planing machines and combined surface/thickness planing machines fitted with an optional mortising device, whose hazards have been dealt with.
This document does not apply to:
a)       machines with more than one cutter block;
b)       machines with a mortising unit driven by a separate motor;
c)        machines where the cutter block is adjustable for depth of cut setting in thickness planing mode;
d)       machines where the conversion from planing to thickness planing mode or vice versa is achieved by mounting or demounting parts/units;
e)       machines where surface planing and thickness planing can be performed at the same time;
f)         machines intended for use in potentially explosive atmosphere;
g)       machines manufactured prior to the publication of this document.

  • Draft
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-11:2024(Main)
Woodworking machines - Safety - Part 11: Combined machines (ISO 19085-11:2024)
SIST EN ISO 19085-11:2024

This document specifies the safety requirements and measures for combined woodworking machines (defined in 3.1), capable of continuous production use, with manual loading and unloading of the workpiece and hereinafter referred to also as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2).
This document deals with all significant hazards, hazardous situations and events, listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document applies to machines also equipped with the devices or additional working units listed in the Scopes of ISO 19085-5:2024, ISO 19085-6:2024, ISO 19085-7:2024 and ISO 19085-9:2024.
This document does not apply to:
a)       machines incorporating a planing unit and a mortising device only;
NOTE            Machines incorporating a planing unit and a mortising device only are dealt with in ISO 19085-7:2024.
b)       combined machines incorporating a band saw unit;
c)        machines with a mortising unit with a separate drive other than the planing unit drive;
d)       machines intended for use in potentially explosive atmosphere;
e)       machines manufactured before the publication of this document.

  • Draft
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-8:2024(Main)
Woodworking machines - Safety - Part 8: Wide belt sanding machines and surface treating machines (ISO 19085-8:2024)
SIST EN ISO 19085-8:2024

This document specifies the safety requirements and measures for wide belt sanding machines (defined in 3.1) and for surface treating machines (defined in 3.2) capable of continuous production use, altogether referred to as “machines”.
This document deals with all significant hazards, hazardous situations and events, as listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer, including reasonably foreseeable misuse. Transport, assembly, dismantling, disabling and scrapping phases are also taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
—     transversal sanding unit;
—     cleaning brushing unit;
—     satining roller unit;
—     disk brushing unit;
—     texturing brushing roller unit;
—     texturing brushing belt unit;
—     cutterblock unit;
—     texturing band saw unit;
—     spiked roller unit;
—     multi blade unit;
—     conveyor directly controlled by the machine;
—     additional workpiece vacuum clamping device;
—     antistatic bar unit.
NOTE 1        An antistatic bar is a device that eliminates electrostatic charges on the workpiece to ease its subsequent cleaning from dust by airflow.
This document is also applicable to machines fitted with a laser engraving unit, but the specific hazards of this unit have not been dealt with.
The machines are designed to process workpieces with flat surface and even thickness, in shape of panels or beams or frames, consisting of:
a)       solid wood;
b)       material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2);
c)        gypsum boards, gypsum bounded fibreboards;
d)       composite materials with core consisting of, e.g. polyurethane or mineral material;
e)       composite boards made from the materials listed above;
f)         all materials listed above, already lacquered.
This document does not deal with hazards related to:
—     specific devices other than those listed above;
—     access through in-feed and out-feed openings of machines with a work piece height capacity greater than 700 mm;
—     systems for powered loading or unloading, or both, of the workpiece to or from a single machine;
NOTE 2        Loading the machine manually includes manually placing the workpiece onto a conveyor directly controlled by the machine. Unloading the machine manually includes manually removing the workpiece from a conveyor directly controlled by the machine.
—     out-feed workpieces on machines with feed speed higher than 60 m/min;
—     interfacing of the machine with any other machine.
This document is not applicable to machines intended for use in a potentially explosive atmosphere and to machines manufactured prior to the date of its publication.

  • Draft
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-6:2024(Main)
Woodworking machines - Safety - Part 6: Single spindle vertical moulding machines (toupie) (ISO 19085-6:2024)
SIST EN ISO 19085-6:2024

This document specifies the safety requirements and measures for single spindle vertical moulding machines (defined in 3.1), capable of continuous production use and hereinafter referred to also as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood.
This document deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to the machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
a)       device to adjust the arbor vertically;
b)       device to tilt the arbor;
c)        device to fit a manually operated tenoning sliding table;
d)       glass bead saw unit;
e)       adjustable table insert;
f)         device for changing the direction of rotation of the spindle;
g)       device for fixing shank mounted tools on the arbor;
h)       interchangeable arbor;
i)         quick tool/arbor change system;
j)         demountable power feed unit;
k)       support for the demountable power feed unit with power-driven adjustments.
This document does not apply to
—     machines equipped with outboard bearings,
—     machines equipped with powered movements of a front extension table and/or a tenoning sliding table.
This document is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

  • Standard
    71 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-12:2021/A11:2023(Amendment)
Woodworking machines - Safety - Part 12: Tenoning/profiling machines (ISO 19085-12:2021)
SIST EN ISO 19085-12:2021/A11:2023
  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-3:2021(Main)
Woodworking machines - Safety - Part 3: Numerically controlled (NC/CNC) boring and routing machines (ISO 19085-3:2021)
SIST EN ISO 19085-3:2022

This document gives the safety requirements and measures for numerically controlled (NC/CNC) boring machines, NC/CNC routing machines and NC/CNC boring and routing machines (as defined in 3.2, 3.3 and 3.4), capable of continuous production use, hereinafter referred to as "machines".
This document deals with all significant hazards, hazardous situations and events, listed in Annex A, relevant to the machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
—    additional working units for sawing, sanding, assembling or dowel inserting;
—    fixed or movable workpiece support;
—    mechanical, pneumatic, hydraulic or vacuum workpiece clamping;
—    automatic tool change devices.
It is also applicable to machines fitted with edge-banding equipment, even if the relevant specific hazards have not been dealt with.
NOTE      For the risk assessment needed for the edge-banding equipment, ISO 19085-17 can be useful.
Machines covered in this document are designed for workpieces consisting of:
—    solid wood;
—    material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2);
—    gypsum boards, gypsum bounded fibreboards, cardboard;
—    matrix engineered mineral boards, silicate boards;
—    composite materials with core consisting of polyurethane or mineral material laminated with light alloy;
—    polymer-matrix composite materials and reinforced thermoplastic/thermoset/elastomeric materials;
—    aluminium light alloy profiles;
—    aluminium light alloy plates with a maximum thickness of 10 mm;
—    composite boards made from the materials listed above.
This document does not deal with specific hazards related to:
—    use of grinding wheels;
—    ejection through openings guarded by curtains on machines where the height of the opening in the enclosure above the workpiece support exceeds 700 mm;
—    ejection due to failure of milling tools with a cutting circle diameter equal to or greater than 16 mm and sawing tools not conforming to EN 847‑1:2017 and EN 847‑2:2017;
—    the combination of a single machine being used with other machines (as a part of a line);
—    integrated workpiece loading/unloading systems (e.g. robots).
This document is not applicable to:
—    single spindle hand fed or integrated fed routing machines;
—    machines intended for use in potentially explosive atmosphere;
—    machines manufactured prior to its publication.

  • Standard
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-16:2021(Main)
Woodworking machines - Safety - Part 16: Table band saws and band re-saws (ISO 19085-16:2021)
SIST EN ISO 19085-16:2022

This document gives the safety requirements and measures for table band saws and band resaws, with manual loading and/or unloading and suitable for continuous production use, hereinafter referred to as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood.
It deals with all significant hazards, hazardous situations and events, listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
a) device to tilt the table;
b) device to tilt the saw unit.
This document does not apply to:
1)    machines driven by combustion engines or power take offs (PTO);
2)    log band sawing machines;
NOTE Log band sawing machines are covered by EN 1807-2:2013.
3)    horizontal band saws and band resaws;
4)    machines designed for cross-cutting of firewood.
This document does not deal with hazards related to the combination of a single machine being used with any other machine (as part of a line).
This document is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day