EN 13445-8:2009
(Main)Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys
Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys
This Part 8 of this European Standard specifies requirements for unfired pressure vessels and their parts made of
aluminium and aluminium alloys in addition to the general requirements for unfired pressure vessels under
EN 13445:2009 Parts 1 to 5. This European Standard specifies unfired pressure vessels for loads up to 500 full
cycles.
NOTE Cast materials are not included in this version. Details regarding cast materials will be subject to an amendment to
or a revision of this European Standard.
Unbefeuerte Druckbehälter - Teil 8: Zusätzliche Anforderungen an Druckbehälter aus Aluminium und Aluminiumlegierungen
Dieser Teil 8 der Europäischen Norm legt zusätzlich zu den allgemeinen Anforderungen an unbefeuerte Druckbehälter
nach EN 13445:2009, Teile 1 bis 5, Anforderungen an aus Aluminium und Aluminiumlegierungen hergestellte
unbefeuerte Druckbehälter und deren Bauteile fest. Dieser Teil der Europäischen Norm gilt für unbefeuerte
Druckbehälter für Druckbelastungen bis zu 500 vollen Lastzyklen.
ANMERKUNG Gusswerkstoffe sind in der vorliegenden Fassung nicht enthalten. Angaben zu Gusswerkstoffen werden in
einer Ergänzung bzw. Überarbeitung dieser Norm aufgenommen.
Récipients sous pression non soumis à la flamme - Partie 8 : exigences complémentaires pour les récipients sous pression en aluminium et alliages d'aluminium
La présente partie 8 de cette Norme européenne spécifie les exigences relatives aux récipients sous pression non
soumis à la flamme et à leurs composants en aluminium et alliages d’aluminium, en complément des exigences
générales énoncées dans les parties 1 à 5 de l’EN 13445:2009. La présente Norme européenne concerne les
récipients sous pression non soumis à la flamme pouvant aller jusqu’à 500 cycles complets de chargement.
NOTE Les matériaux moulés ne sont pas inclus pour l’instant. Des détails relatifs aux matériaux moulés feront l’objet d’un
amendement ou à une révision de la présente Norme européenne.
Neogrevane tlačne posode - 8. del: Dodatne zahteve za tlačne posode iz aluminija in aluminijevih zlitin
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Unbefeuerte Druckbehälter - Teil 8: Zusätzliche Anforderungen an Druckbehälter aus Aluminium und AluminiumlegierungenRécipients sous pression non soumis à la flamme - Partie 8 : exigences complémentaires pour les récipients sous pression en aluminium et alliages d'aluminiumUnfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys77.150.10Aluminijski izdelkiAluminium products23.020.30MHNOHQNHPressure vessels, gas cylindersICS:Ta slovenski standard je istoveten z:EN 13445-8:2009SIST EN 13445-8:2009en,fr,de01-november-2009SIST EN 13445-8:2009SLOVENSKI
STANDARDSIST EN 13445-8:20071DGRPHãþD
SIST EN 13445-8:2009
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13445-8July 2009ICS 23.020.30Supersedes EN 13445-8:2006
English VersionUnfired pressure vessels - Part 8: Additional requirements forpressure vessels of aluminium and aluminium alloysRécipients sous pression non soumis à la flamme - Partie 8: exigences complémentaires pour les récipients souspression en aluminium et alliages d'aluminiumUnbefeuerte Druckbehälter - Teil 8: ZusätzlicheAnforderungen an Druckbehälter aus Aluminium undAluminiumlegierungenThis European Standard was approved by CEN on 30 June 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13445-8:2009: ESIST EN 13445-8:2009
EN 13445-8:2009 (E) Issue 1 (2009-07) 2 Contents Page Foreword.4 1 Scope.5 2 Normative references.5 3 Terms, definitions, symbols and units.6 4 General requirements.6 5 Materials.6 5.1 General.6 5.2 Elongation after fracture.6 5.3 Prevention of brittle fracture.6 5.4 Lamellar tearing.7 5.5 Chemical composition.7 5.6 Material grouping system.7 6 Design.8 6.1 General.8 6.2 Design temperature and properties.8 6.3 Time-independe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.