EN ISO 9405:2017
(Main)Textile floor coverings - Assessment of changes in appearance (ISO 9405:2015)
Textile floor coverings - Assessment of changes in appearance (ISO 9405:2015)
ISO 9405:2015 describes the procedures for assessing the overall change in appearance of textile floor coverings caused by Vettermann drum and hexapod tumbler testers according to ISO 10361 and ISO 4918.
Textile Bodenbeläge - Beurteilung der Aussehensveränderung (ISO 9405:2015)
Revêtements de sol textiles - Évaluation des changements d'aspect (ISO 9405:2015)
L'ISO 9405:2015 décrit les méthodes d'évaluation du changement global d'aspect des revêtements de sol textiles provoqués par un tambour Vettermann et un tambour d'essai pour hexapode, conformes aux ISO 10361 et ISO 4918.
Tekstilne talne obloge - Ocenitev sprememb videza (ISO 9405:2015)
Ta mednarodni standard opisuje postopke za ocenjevanje celotne spremembe videza tekstilnih talnih oblog, ki jih povzročijo bobnasti in šestnožni preskuševalniki po Vettermannu v skladu s standardoma ISO 10361 in ISO 4918.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2017
1DGRPHãþD
SIST EN 1471:1999
SIST EN 1471:1999/A1:2004
Tekstilne talne obloge - Ocenitev sprememb videza (ISO 9405:2015)
Textile floor coverings - Assessment of changes in appearance (ISO 9405:2015)
Textile Bodenbeläge - Beurteilung der Aussehensveränderung (ISO 9405:2015)
Revêtements de sol textiles - Évaluation des changements d'aspect (ISO 9405:2015)
Ta slovenski standard je istoveten z: EN ISO 9405:2017
ICS:
97.150 Talne obloge Floor coverings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 9405
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2017
EUROPÄISCHE NORM
ICS 97.150 Supersedes EN 1471:1996
English Version
Textile floor coverings - Assessment of changes in
appearance (ISO 9405:2015)
Revêtements de sol textiles - Évaluation des Textile Bodenbeläge - Beurteilung der
changements d'aspect (ISO 9405:2015) Aussehensveränderung (ISO 9405:2015)
This European Standard was approved by CEN on 8 June 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9405:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
The text of ISO 9405:2015 has been prepared by Technical Committee ISO/TC 219 “Floor coverings” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 9405:2017
by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings” the secretariat of
which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2017, and conflicting national standards
shall be withdrawn at the latest by December 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN 1471:1996.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 9405:2015 has been approved by CEN as EN ISO 9405:2017 without any modification.
INTERNATIONAL ISO
STANDARD 9405
Second edition
2015-02-01
Textile floor coverings — Assessment
of changes in appearance
Revêtements de sol textiles — Évaluation des changements d’aspect
Reference number
ISO 9405:2015(E)
©
ISO 2015
ISO 9405:2015(E)
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved
ISO 9405:2015(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 General apparatus . 2
5.1 Viewing cabinet . 2
5.2 Digital images (reference scales for assessing appearance change) . 3
5.3 Large grey scales . 3
6 Selection and preparation of specimens . 3
7 Assessment of change. 3
7.1 Assessors . 3
7.2 Procedure . 3
7.3 Change of colour . 4
7.4 Test report . 4
Annex A (informative) Precision of the test method . 5
Bibliography . 6
ISO 9405:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT), see the following URL: Foreword — Supplementary information.
The committee responsible for this document is ISO/TC 219, Floor coverings.
This second edition cancels and replaces the first edition (ISO 9405:2001), which has been technically
revised.
iv © ISO 2015 – All rights reserved
INTERNATIONAL STANDARD ISO 9405:2015(E)
Textile floor coverings — Assessment of changes in
appearance
1 Scope
This International Standard describes the procedures for assessing the overall change in appearance of
textile floor coverings caused by Vettermann drum and hexapod tumbler testers according to ISO 10361
and ISO 4918.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 105-A01, Textiles — Tests for colour fastness — Part A01: General principles of testing
ISO 105-A02, Textiles — Tests for colour fastness — Part A02: Grey scale for assessing change in colour
ISO 2424, Textile floor coverings — Vocabulary
ISO 4918, Resilient, textile and laminate floor coverings — Castor chair test
ISO 10361, Textile Floor coverings — Production of changes in appearance by means of Vettermann drum
and hexapod tumbler testers
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 2424 and the following apply:
3.1
change in surface appearance
difference between a fatigued and an unfatigued specimen
Note 1 to entry: The degree of change is expressed by reference to standard digital image reference scales and by
reference to large grey scales, grade 5 representing no change and grade 1 an extreme change.
Note 2 to entry: Changes in structure, roughness, colour, and/or pattern of a textile floor covering may contribute
to change in appearance. It is not always possible to distinguish clearly between the factors since each can have
an interaction with others.
3.2
change in structure
textural change
visible change in configuration of loops and tufts and/or fibres at the use-surface of a textile floor covering
3.3
loss of tuft definition
decrease of the pile definition caused by the bursting, opening, and untwisting of the pile yarn and/or
decrimping of the fibres in the use-surface of a textile floor covering
3.4
crushing
flattening
loss of thickness of a textile floor covering under the action of a static or dynamic load
ISO 9405:2015(E)
3.5
felting
matting
loss of pile definition of a textile floor covering due to entanglement and compression of pile fibres
3.6
hairiness
filamentation
protrusion of fibres above the normal level of the use-surface of a textile floor covering and not removable
by brushing or suction
3.7
cobwebbing
extreme form of hairiness (3.6) in which the fibres are entangled to form an interlaced web attached to
the use-surface
3.8
pilling
extreme form of hairiness (3.6) in which the fibres are entangled to form small aggregates, attached to
the use-surface, which can or cannot include fibres from other sources
3.9
sprouting
release and appearance during use of extra-long tuft legs which were accidentally trapped within the
pile of a textile floor covering during manufacture
3.10
change of pattern definition
change in the colour appearance of patterned textile floor coverings due to mechanical action
Note 1 to entry: A change of pattern definition can
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.