EN ISO 1519:2002

Paints and varnishes - Bend test (cylindrical mandrel) (ISO 1519:2002)

This International Standard specifies an empirical test procedure for assessing the resistance of a coating of paint, varnish or related product to cracking and/or detachment from a metal or plastic substrate when subjected to bending round a cylindrical mandrel under standard conditions.
For a multicoat system, each coat may be tested separately or the complete system may be tested.
The method specified may be carried out either as a "go/no go" test, by carrying out the test with a single specified size of mandrel, to assess compliance with a particular requirement, or by repeating the procedure using successively smaller mandrels to determine the diameter of the first mandrel over which the coating cracks and/or becomes detached from the substrate.
Two types of apparatus are specified, type 1 being appropriate for use on test panels of thickness up to 0,3 mm, and type 2 for use on test panels of thickness up to 1,0 mm. Both types of apparatus have been found to give similar results with the same coating, but normally only one will be used for testing a given product.

Beschichtungsstoffe - Dornbiegeversuch (zylindrischer Dorn) (ISO 1519:2002)

Diese Internationale Norm legt ein empirisches Prüfverfahren zum Bewerten der Widerstandsfähigkeit von Beschichtungen aus Beschichtungsstoffen wie Lacken, Anstrichstoffen oder ähnlichen Produkten gegen Rissbildung und/oder Ablösen von einem Substrat aus Metall oder Kunststoff fest, wenn dieses unter Normbedingungen um einen zylindrischen Dorn gebogen wird.
Bei einem Mehrschichtsystem kann jede Schicht für sich allein oder das gesamte System geprüft werden.
Das festgelegte Verfahren kann durchgeführt werden
¾ entweder als �ja/nein"-Prüfung, indem die Prüfung mit einem einzigen Dorn mit festgelegtem Durchmesser durchgeführt wird, um die Übereinstimmung mit einer bestimmten Anforderung festzustellen,
¾ oder durch wiederholte Prüfungen, indem nacheinander Dorne mit jeweils kleinerem Durchmesser angewendet werden, um den Durchmesser des ersten Dorns zu bestimmen, über dem die Beschichtung das erste Mal reißt und/oder sich vom Substrat ablöst.
Es sind zwei Gerätetypen festgelegt. Typ 1 ist zur Anwendung für Probenplatten mit einer Dicke bis 0,3 mm, Typ 2 für solche mit einer Dicke bis 1,0 mm geeignet. Mit beiden Typen werden an der gleichen Beschichtung ähnliche Ergebnisse erhalten. Im Allgemeinen wird für die Prüfung eines gegebenen Produktes aber nur ein Gerätetyp angewendet.

Peintures et vernis - Essai de pliage sur mandrin cylindrique (ISO 1519:2002)

La présente Norme Internationale spécifie une méthode d'essai empirique permettant d'évaluer la résistance d'une couche de peinture, de vernis ou de produit assimilé aux craquelures et/ou au décollement d'un subjectile métallique ou en matière plastique lorsqu'il est plié sur un mandrin cylindrique dans des conditions normalisées.
Pour un système multicouche, l'essai peut porter sur chaque couche séparément ou sur le système complet.
La méthode spécifiée peut être mise en oeuvre soit comme un essai «tout ou rien», l'essai étant effectué avec une dimension spécifiée unique du mandrin pour évaluer la conformité à une exigence particulière, soit  en utilisant des mandrins de plus en plus petits pour déterminer le diamètre du premier mandrin sur lequel la couche se craquelle et/ou se décolle du subjectile.
Deux types d'appareils sont spécifiés; le type 1 convient pour des panneaux d'essai dont l'épaisseur est inférieure ou égale à 0,3 mm, le type 2 pour des panneaux d'essai dont l'épaisseur est inférieure ou égale à 1,0 mm. Ces deux types d'appareils donnent des résultats semblables pour le même revêtement, mais normalement un seul sera utilisé pour essayer un produit donné.

Barve in laki - Preskus s pregibom (cilindrični trn) (ISO 1519:2002)

General Information

• Status: Withdrawn
• Publication Date: 14-Mar-2002
• Withdrawal Date: 14-Jan-2011
• ICS: 87.040 - Paints and varnishes
• Technical Committee: CEN/TC 139 - Paints and varnishes
• Drafting Committee: CEN/TC 139 - Paints and varnishes
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 15-Jan-2011
• Completion Date: 15-Jan-2011
• Ref Project: SIST EN ISO 1519:2002 - Paints and varnishes - Bend test (cylindrical mandrel) (ISO 1519:2002)

Relations

• Replaces: EN ISO 1519:1995 - Paints and varnishes - Bend test (cylindrical mandrel) (ISO 1519:1973)
• Effective Date: 22-Dec-2008
• Replaced By: EN ISO 1519:2011 - Paints and varnishes - Bend test (cylindrical mandrel) (ISO 1519:2011)
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 1519:2002
01-september-2002
1DGRPHãþD
SIST EN ISO 1519:1997
%DUYHLQODNL3UHVNXVVSUHJLERPFLOLQGULþQLWUQ,62
Paints and varnishes - Bend test (cylindrical mandrel) (ISO 1519:2002)
Beschichtungsstoffe - Dornbiegeversuch (zylindrischer Dorn) (ISO 1519:2002)
Peintures et vernis - Essai de pliage sur mandrin cylindrique (ISO 1519:2002)
Ta slovenski standard je istoveten z: EN ISO 1519:2002
ICS:
87.040 Barve in laki Paints and varnishes
SIST EN ISO 1519:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 1519:2002

---------------------- Page: 2 ----------------------

SIST EN ISO 1519:2002
EUROPEAN STANDARD
EN ISO 1519
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2002
ICS 87.040 Supersedes EN ISO 1519:1995
English version
Paints and varnishes - Bend test (cylindrical mandrel) (ISO
1519:2002)
Peintures et vernis - Essai de pliage sur mandrin Beschichtungsstoffe - Dornbiegeversuch (zylindrischer
cylindrique (ISO 1519:2002) Dorn) (ISO 1519:2002)
This European Standard was approved by CEN on 4 March 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1519:2002 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 1519:2002
EN ISO 1519:2002 (E)
CORRECTED  2002-04-24
Foreword
This document (ISO 1519:2002) has been prepared by Technical Committee ISO/TC 35
"Paints and varnishes" in collaboration with Technical Committee CEN/TC 139 "Paints and
varnishes", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by September 2002, and conflicting
national standards shall be withdrawn at the latest by September 2002.
This document supersedes EN ISO 1519:1995.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the
United Kingdom.
Endorsement notice
The text of the International Standard ISO 1519:2002 has been approved by CEN as a
European Standard without any modifications.
NOTE Normative references to International Standards are listed in annex ZA (normative).
2

---------------------- Page: 4 ----------------------

SIST EN ISO 1519:2002
EN ISO 1519:2002 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions
of any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications,
indicated by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 1513 1992 Paints and varnishes - Examination EN ISO 1513 1994
and preparation of samples for
testing
ISO 1514 1993 Paints and varnishes - Standard EN ISO 1514 1997
panels for testing
ISO 2808 1997 Paints and varnishes - EN ISO 2808 1999
Determination of film thickness
ISO 3270 1984 Paints and varnishes and their raw EN 23270 1991
materials - Temperatures and
humidities for conditioning and
testing
ISO 15528 2000 Paints, varnishes and raw materials EN ISO 155
...