EN ISO 18753:2017
(Main)Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of absolute density of ceramic powders by pycnometer (ISO 18753:2017)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of absolute density of ceramic powders by pycnometer (ISO 18753:2017)
ISO 18753:2017 specifies a method for determining the absolute particle density of fine ceramic powders or sintered parts using liquid pycnometry.
NOTE Other pycnometer methods like gas pycnometers (e.g. helium pycnometer), where a gas is used as media, also exist.
Hochleistungskeramik - Bestimmung der absoluten Dichte keramischer Pulver mit einem Pyknometer (ISO 18753:2017)
Céramiques techniques - Détermination de la masse volumique absolue des poudres céramiques à l'aide d'un pycnomètre (ISO 18753:2017)
ISO 18753:2017 spécifie une méthode permettant de déterminer, à l'aide d'un pycnomètre à liquide, la masse volumique absolue de poudres céramiques ou d'objets obtenus par frittage.
NOTE Il existe d'autres méthodes pycnométriques telles que celles impliquant l'utilisation d'un pycnomètre à gaz (par exemple, un pycnomètre à l'hélium) dans lequel un gaz est utilisé comme milieu d'immersion.
Fina keramika (sodobna keramika, sodobna tehnična keramika) - Določanje absolutne gostote keramičnih praškov s piknometrom (ISO 18753:2017)
Ta dokument opredeljuje metodo za določanje absolutne gostote finih keramičnih praškov ali sintranih delov s tekočinskim piknometrom.
OPOMBA: Obstajajo tudi metode z uporabo drugih piknometrov, kot so plinski piknometri (npr. helijev piknometer), kjer se kot medij uporablja plin.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2017
1DGRPHãþD
SIST EN ISO 18753:2006
)LQDNHUDPLND VRGREQDNHUDPLNDVRGREQDWHKQLþQDNHUDPLND 'RORþDQMH
DEVROXWQHJRVWRWHNHUDPLþQLKSUDãNRYVSLNQRPHWURP ,62
Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of
absolute density of ceramic powders by pyknometer (ISO 18753:2017)
Hochleistungskeramik - Bestimmung der absoluten Dichte keramischer Pulver mit einem
Pyknometer (ISO 18753:2017)
Céramiques techniques - Détermination de la masse volumique absolue des poudres
céramiques à l'aide d'un pycnomètre (ISO 18753:2017)
Ta slovenski standard je istoveten z: EN ISO 18753:2017
ICS:
17.060 Merjenje prostornine, mase, Measurement of volume,
gostote, viskoznosti mass, density, viscosity
81.060.30 Sodobna keramika Advanced ceramics
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 18753
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2017
EUROPÄISCHE NORM
ICS 81.060.30 Supersedes EN ISO 18753:2005
English Version
Fine ceramics (advanced ceramics, advanced technical
ceramics) - Determination of absolute density of ceramic
powders by pycnometer (ISO 18753:2017)
Céramiques techniques - Détermination de la masse Hochleistungskeramik - Bestimmung der absoluten
volumique absolue des poudres céramiques à l'aide Dichte keramischer Pulver mit einem Pyknometer (ISO
d'un pycnomètre (ISO 18753:2017) 18753:2017)
This European Standard was approved by CEN on 6 August 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18753:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 18753:2017) has been prepared by Technical Committee ISO/TC 206 “Fine
ceramics” in collaboration with Technical Committee CEN/TC 184 “Ergonomics” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2018 and conflicting national standards shall be
withdrawn at the latest by March 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 18753:2005.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 18753:2017 has been approved by CEN as EN ISO 18753:2017 without any modification.
INTERNATIONAL ISO
STANDARD 18753
Second edition
2017-08
Fine ceramics (advanced ceramics,
advanced technical ceramics) —
Determination of absolute density of
ceramic powders by pycnometer
Céramiques techniques — Détermination de la masse volumique
absolue des poudres céramiques à l’aide d’un pycnomètre
Reference number
ISO 18753:2017(E)
©
ISO 2017
ISO 18753:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO 18753:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Preparation of measurement . 2
4.1 Sampling . 2
4.2 Drying of sample . 2
4.3 Preparation of immersion liquid . 2
5 Apparatus . 2
6 Procedure. 3
7 Calculation . 4
8 Tests in duplicate . 5
9 Test report . 5
Annex A (normative) Reference data for absolute density of distilled water .6
Bibliography . 7
ISO 18753:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w . i s o .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 206, Fine ceramics.
This second edition cancels and replaces the first edition (ISO 18753:2004), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— Clause 6 has been modified to include changes in list items d) and g) and to add a paragraph
discussing factors affecting accuracy of test results;
[1]
— Table A.1 has been modified with new reference data for the absolute density of distilled water .
iv © ISO 2017 – All rights reserved
INTERNATIONAL STANDARD ISO 18753:2017(E)
Fine ceramics (advanced ceramics, advanced technical
ceramics) — Determination of absolute density of ceramic
powders by pycnometer
1 Scope
This document specifies a method for determining the absolute particle density of fine ceramic powders
or sintered parts using liquid pycnometry.
NOTE Other pycnometer methods like gas pycnometers (e.g. helium pycnometer), where a gas is used as
media, also exist.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 758, Liquid chemical products for industrial use — Determination of density at 20 °C
ISO 3507, Laboratory glassware — Pyknometers
ISO 6353-2, Reagents for chemical analysis — Part 2: Specifications — First series
ISO 6353-3, Reagents for chemical analysis — Part 3: Specifications — Second series
ISO 8213, Chemical products for industrial use — Sampling techniques — Solid chemical products in the
form of particles varying from powders to coarse lumps
ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at http:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
3.1
absolute particle density
absolute density of ceramic powders
density of an individual ceramic particle, a ceramic powder or sintered parts
Note 1 to entry: When an enclosed space occurs (pore) inside the particle or part, the space is considered to be
part of the individual particle or part. The result of the test is then the absolute density of the ceramic particles or
ceramic parts with closed porosity.
Note 2 to entry: If the intention of the test is to determine the absolute density of a ceramic material, the test is
limited to particles or parts without closed porosity.
ISO 18753:2017(E)
3.2
particle
ceramic powder or an amount of small sintered ceramic parts
EXAMPLE Grinding balls or other small parts.
Note 1 to entry: When the examined material has closed porosity inside the particles, the measured density is
not the absolute density of the material but of the examined part.
3.3
pycnometry
method of measuring absolute particle density using a pycnomete
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.