ENV 500-6:1995
(Main)Mobile road construction machinery - Safety - Part 6: Specific requirements for paver-finishers
- BACK
- 17-Oct-1995
- 03-Oct-2006
- 91.220
- 98/37/EC
- M/BC/CEN/91/1
- CEN/TC 151
Mobile road construction machinery - Safety - Part 6: Specific requirements for paver-finishers
Part 6 of this standard specifies the safety requirements for paver-finishers as defined in clause 3 and deals with the significant hazards pertinent to paver-finishers, when used as intended and in conditions foreseen by the manufacturer.
Bewegliche Straßenbaumaschinen - Sicherheit - Teil 6: Besondere Anforderungen an Straßenfertiger
Teil 6 dieser Norm legt die sicherheitstechnischen Anforderungen für Straßenfertiger - wie in Abschnitt 3 definiert - fest, und behandelt die artspezifischen Gefährdungen, die von Straßenfertiger ausgehen, wenn sie bestimmungsgemäß entsprechend den Empfehlungen des Herstellers verwendet werden.
Machines mobiles pour la construction de routes - Sécurité - Partie 6: Exigences spécifiques pour finisseurs
La partie 6 de cette norme prescrit les exigences de sécurité applicables aux découpeurs de joints - tels qu'ils sont définis dans l'article 3 - et traite les phénomènes dangereux significatifs résultant des découpeurs de joints, quand ils sont utilisés normalement et conformément aux recommandations du fabricant.
Mobile road construction machinery - Safety - Part 6: Specific requirements for paver-finishers
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST ENV 500-6:2000
01-december-2000
Mobile road construction machinery - Safety - Part 6: Specific requirements for
paver-finishers
Mobile road construction machinery - Safety - Part 6: Specific requirements for paver-
finishers
Bewegliche Straßenbaumaschinen - Sicherheit - Teil 6: Besondere Anforderungen an
Straßenfertiger
Machines mobiles pour la construction de routes - Sécurité - Partie 6: Exigences
spécifiques pour finisseurs
Ta slovenski standard je istoveten z: ENV 500-6:1995
ICS:
93.080.10 Gradnja cest Road construction
SIST ENV 500-6:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali
...
This May Also Interest You
This document applies to transportable masonry and stone cutting-off machines stationary during work, principally used on job site building construction for cutting-off stones, other mineral construction materials and composite materials having at least one supporting surface. The power for the tool rotation is supplied by electrical or internal combustion prime motor.
This document deals with all significant hazards, hazardous situations or hazardous events relevant to masonry and stone cutting-off machines for job site (see Annex A), when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer. This document specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during the lifetime of the machinery as described in EN ISO 12100:2010, 5.4.
These machines are designed for use with rotating diamond cutting-off wheels with a continuous rim and/or segmented rim.
This document does not apply to:
- metal cutting-off machines;
- wood and timber sawing machines;
- machines with a feed or descent mechanism other than manual, or with a pedal;
- mobile machines on a trolley travelling on the ground;
- hand-held portable grinding and cutting-off machines;
- hand-held portable grinding and cutting-off machines mounted on a support to be used in a fixed position.
This document does not cover the operation of transportable masonry and stone cutting-off machines in potential explosive atmospheres.
In this document, the masonry and stone cutting-off machines for job site construction are called: “cutting-off machines” or “machines”, and cutting-off wheels are also called: “tools”.
This document applies to machines which are manufactured after the date of approval of the standard by CEN.
- Standard49 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft43 pagesEnglish languagesale 10% offe-Library read for×1 day
- 30-Mar-2022
- 29-Jun-2022
- 91.220
- 2006/42/EC
- M/396
- CEN/TC 151
1.1 This document specifies the safety requirements for truck mixers.
This document also covers the interface between the mixing unit and the truck or trailer (but not the truck or trailer itself).
NOTE 1 Truck or trailer constructed primarily for the carriage of goods as classified according to directive 2007/46/EC, category N3 or O4.
This document does not cover:
a) additional equipment (conveyor belt, mortar pump, concrete pump, concrete-placing boom);
b) requirements for operation in tunnels;
c) truck or self-propelled mixers equipped with self-loading systems;
d) front-discharge mixers;
e) mixing units with articulated steering;
f) truck mixer drum cleaning systems;
g) energy source(s).
This document does not deal with carrier vehicles, e.g. trucks, tractors, construction machinery and mobile industrial handling equipment or other self-propelled vehicles.
This document does not include requirements which are covered in directives related to the construction of vehicles or national road regulations.
NOTE 2 The use in public road traffic is governed by the national regulations.
1.2 This document deals with all significant hazards, hazardous situations and events relevant to truck mixers when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex D). This document specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during transportation, assembly, dismantling, disabling, scrapping, operation and maintenance of the truck mixer.
1.3 This document is not applicable to machines which are manufactured before the date of publication of this document by CEN.
- Standard53 pagesEnglish languagesale 10% offe-Library read for×1 day
- 29-Apr-2021
- 30-Jul-2021
- 91.220
- 2006/42/EC
- M/396
- CEN/TC 151
This document, to be used together with EN 1009-1, specifies the safety requirements and their verification for the design and construction of machinery for cleaning, water recycling, mud treatment and sorting (other than screens) for the mechanical processing in quarrying, recycling and processing mineral and by-products. In addition, it specifies the type of information on safe working practices (including residual risks) to be provided by the manufacturer.
When requirements of this part of EN 1009 are different from those which are stated in EN 1009-1:2020, the requirements of this part of EN 1009 take precedence over the requirements of EN 1009-1:2020 for machines that have been designed and built according to the provisions of this part of EN 1009.
This document, together with EN 1009-1:2020, deals with all the significant hazards, hazardous situations and events relevant to machinery for cleaning, recycling, mud treatment when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer associated with the whole lifetime of the machine (see Annex C).
This document does not cover:
- design relating to road traffic regulations;
- hazards arising from the use of the machines in potentially explosive atmospheres as well as from processing of explosive materials and risks related to electromagnetic compatibility;
- specific hazards related to mobile machinery.
NOTE 1 EN ISO 13766-1 and EN ISO 13766-2 specify test methods and acceptance criteria for evaluating the electromagnetic compatibility of all kinds of mobile construction machinery.
NOTE 2 prEN 1009-6 "Specific requirements for mobile and semi mobile equipment" is under preparation to cover specific requirements (e.g. mobility, braking, access, frequent transportation), including exceptions and additional requirements for mobile and semi mobile equipment. This means that mobile machines are not covered as long as EN 1009-6 is not published by CEN.
This document is not applicable to machinery for cleaning, recycling, mud treatment and sorting which are manufactured before the date of publication of this document by CEN.
- Standard39 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft37 pagesEnglish languagesale 10% offe-Library read for×1 day
- 30-Aug-2020
- 30-May-2022
- 73.120
- 91.220
- 2006/42/EC
- M/396
- CEN/TC 151
This document, to be used together with EN 1009-1:2020, specifies the safety requirements and their verification for the design and construction of screening machinery for the mechanical processing in quarrying, recycling and processing mineral and by-products as defined in 3.1.
In addition, it specifies the type of information on safe working practices (including residual risks) to be provided by the manufacturer.
When requirements of this document are different from those which are stated in EN 1009-1:2020, the requirements of this document take precedence over the requirements of EN 1009-1:2020 for machines that have been designed and built according to the provisions of this document.
This document, together with EN 1009-1:2020, deals with all the significant hazards, hazardous situations and events relevant to screening machinery when they are used as intended and under the conditions foreseen by the manufacturer (see Annex C).
This document does not cover:
- design relating to road traffic regulations;
- hazards arising from the use of the machines in potentially explosive atmospheres as well as from processing of explosive materials and risks related to electromagnetic compatibility;
- specific hazards related to mobile machinery.
NOTE 1 EN ISO 13766-1 and EN ISO 13766-2 specify test methods and acceptance criteria for evaluating the electromagnetic compatibility of all kinds of mobile construction machinery.
NOTE 2 prEN 1009-6 "Specific requirements for mobile and semi mobile equipment" is under preparation to cover specific requirements (e.g. mobility, braking, access, frequent transportation), including exceptions and additional requirements for mobile and semi mobile equipment. This means that mobile machines are not covered as long as EN 1009-6 is not published by CEN.
This document is not applicable to screening machinery which are manufactured before the date of publication of this document by CEN.
- Standard37 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft30 pagesEnglish languagesale 10% offe-Library read for×1 day
- 30-Aug-2020
- 30-May-2022
- 73.120
- 91.220
- 2006/42/EC
- M/396
- CEN/TC 151
This document applies to machines for mechanical processing of minerals (cement, lime and gypsum, sand and gravel, industrial minerals, metalliferous ore and hard and soft rock aggregates, coal) and -products (slag and ashes, production and demolition waste) in construction and industry.
It deals with the following types of individual machines for the mechanical processing of minerals and similar solid materials:
- feeding machinery in accordance with EN 1009-2;
- crushing machinery in accordance with EN 1009-3;
- milling machinery in accordance with EN 1009-3;
- screening machinery in accordance with EN 1009-4;
- machinery for cleaning, water recycling, sorting (other than screens) and mud treatment in accordance with EN 1009-5;
- mobile machinery in accordance with prEN 1009-6.
This document gives the common safety requirements for mechanical processing machines used for quarrying, recycling and processing mineral and by-products (cement, lime and gypsum, sand and gravel, industrial minerals, metalliferous ore, production and demolition waste, slag handling, hard and soft rock aggregates, coal) in construction and surface mining and is intended to be used in conjunction with one of the parts EN 1009-2 to prEN 1009-6. These machine specific parts (EN 1009-2 to prEN 1009-6) do not repeat the requirements from this document, but add or replace the requirements for the machine type in question.
NOTE 1 The requirements specified in this part of EN 1009 are common to two or more types of machines for the mechanical processing of minerals and similar solid materials.
Specific requirements in EN 1009 2 to prEN 1009-6 take precedence over the respective requirements of this document.
This document also covers assemblies of two or more of the mentioned machines which function as an integrated whole. The machines included in the scope of this document can be fixed, semi-mobile or mobile.
NOTE 2 prEN 1009-6 "Specific requirements for mobile and semi mobile equipment" is under preparation to cover specific requirements (e.g. mobility, braking, access, frequent transportation), including exceptions and additional requirements for mobile and semi mobile equipment. This means that mobile machines are not covered as long as EN 1009-6 is not published by CEN.
This document covers transportation, erection, commissioning, use and maintenance of single machines or combination of single machines.
This document deals with significant hazards, common to the types of machines listed in this scope when they are used as intended and under conditions for misuse which are reasonably foreseeable by the manufacturer (see Annex F) and to the hazards due to the combination of these machines and specifies the appropriate measures to eliminate or reduce the risks arising from the significant hazards.
Design relating to road traffic regulations is not covered by this document.
This document does not cover:
- design relating to road traffic regulations;
- hazards arising from the use of the machines in potentially explosive atmospheres as well as from processing of explosive materials and risks related to electromagnetic compatibility;
- specific hazards related to mobile machinery.
NOTE 3 EN ISO 13766-1 and EN ISO 13766-2 specify test methods and acceptance criteria for evaluating the electromagnetic compatibility of all kinds of mobile construction machinery.
This document is not applicable to machinery which are manufactured before the date of publication of this document by CEN.
- Standard89 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft72 pagesEnglish languagesale 10% offe-Library read for×1 day
- 30-Aug-2020
- 30-May-2022
- 73.120
- 91.220
- 2006/42/EC
- M/396
- CEN/TC 151
This document specifies safety requirements and measures for their verification for the design and construction of portable, hand-held, internal combustion engine-driven cut-off machines intended to be used by a single operator in the cutting of construction materials, such as asphalt, concrete, stone and metal. It is applicable only to those machines designed purposely for use with a rotating, bonded-abrasive and/or super-abrasive (for example diamond) cut-off wheel having a maximum outer diameter of 430 mm, centre-mounted on and driven by a spindle shaft where the top of the wheel rotates away from the operator (see Figure 1).
This document deals with all significant hazards, hazardous situations or hazardous events significant to these machines when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer. See Annex F for a list of significant hazards.
This document specifies methods for the elimination or reduction of hazards arising from their use, as well as the type of information on safe working practices to be provided with the machines.
Cut-off wheel specifications are not considered in this document. Cut-off wheels are deemed to comply to existing cut-off wheel standards.
NOTE For example see Bibliography.
All through the document, portable, hand-held, internal combustion engine-driven cut-off machines are called "cut-off machines".
This document is not applicable to machines manufactured before the date of its publication.
- Standard62 pagesEnglish languagesale 10% offe-Library read for×1 day
- 30-May-2020
- 30-Aug-2020
- 91.220
- 2006/42/EC
- M/396
- CEN/TC 151
This document, to be used together with EN 1009-1, specifies the safety requirements and their verification for the design and construction of feeding machinery and continuous handling equipment for the mechanical processing in quarrying, recycling and processing mineral and by-products. In addition, it specifies the specific information (including residual risks) to be provided by the manufacturer.
When requirements of this document are different from those which are stated in EN 1009-1:2020, the requirements of this part of EN 1009 take precedence over the requirements of EN 1009-1:2020 for machines that have been designed and built according to the provisions of this document.
This document, together with EN 1009-1:2020, deals with all the significant hazards, hazardous situations and events relevant to feeding machinery when they are used as intended and under the conditions foreseen by the manufacturer (see Annex C).
This document does not cover:
- design relating to road traffic regulations;
- hazards arising from the use of the machines in potentially explosive atmospheres as well as from processing of explosive materials and risks related to electromagnetic compatibility;
- specific hazards related to mobile machinery.
NOTE 1 EN ISO 13766-1 and EN ISO 13766-2 specify test methods and acceptance criteria for evaluating the electromagnetic compatibility of all kinds of mobile construction machinery.
NOTE 2 prEN 1009-6 "Specific requirements for mobile and semi mobile equipment" is under preparation to cover specific requirements (e.g. mobility, braking, access, frequent transportation), including exceptions and additional requirements for mobile and semi mobile equipment. This means that mobile machines are not covered as long as EN 1009-6 is not published by CEN.
This document is not applicable to feeding machinery and continuous handling equipment which are manufactured before the date of publication of this document by CEN.
- Standard27 pagesEnglish languagesale 10% offe-Library read for×1 day
- 26-May-2020
- 30-May-2022
- 73.120
- 91.220
- 2006/42/EC
- M/396
- CEN/TC 151
This document, to be used together with EN 1009-1:2020, specifies the safety requirements and their verification for the design and construction of crushing and milling machinery for the mechanical processing in quarrying, recycling and processing mineral and by-products. In addition, it specifies the type of information on safe working practices (including residual risks) to be provided by the manufacturer.
When requirements of this part of EN 1009 are different from those which are stated in EN 1009-1:2020, the requirements of this part of EN 1009 take precedence over the requirements of EN 1009-1:2020 for machines that have been designed and built according to the provisions of this part of EN 1009.
This document, together with EN 1009-1:2020, deals with all the significant hazards, hazardous situations and events relevant to crushing and milling machinery when they are used as intended and under the conditions foreseen by the manufacturer (see Annex C).
This document does not cover:
- design relating to road traffic regulations;
- hazards arising from the use of the machines in potentially explosive atmospheres as well as from processing of explosive materials and risks related to electromagnetic compatibility;
- specific hazards related to mobile machinery.
NOTE 1 EN ISO 13766-1 and EN ISO 13766-2 specify test methods and acceptance criteria for evaluating the electromagnetic compatibility of all kinds of mobile construction machinery.
NOTE 2 prEN 1009-6 "Specific requirements for mobile and semi mobile equipment' is under preparation to cover specific requirements (e.g. mobility, braking, access, frequent transportation), including exceptions and additional requirements for mobile and semi mobile equipment. This means that mobile machines are not covered as long as EN 1009-6 is not published by CEN.
This document is not applicable to crushing and milling machinery which are manufactured before the date of publication of this document by CEN.
- Standard32 pagesEnglish languagesale 10% offe-Library read for×1 day
- 26-May-2020
- 30-May-2022
- 73.120
- 91.220
- 2006/42/EC
- M/396
- CEN/TC 151
This European Standard specifies the safety requirements applicable to stationary and relocatable mixing plants for the production of materials (e.g. hot-mix asphalt, cold-mix asphalt, cement gravel) used for the construction and maintenance of traffic routes (roads, highways, sidewalks, airfields, etc.) water retaining works, dam walls, culverts, etc.
This European Standard applies to the following types of mixing plant:
a) hot Asphalt mixing plant;
b) cold mixing plant (e.g. for production of cement gravel, cold mix asphalt);
c) mixing plant for bituminous or non-bituminous reclaimed materials;
d) mixing plant for mastic asphalt, also including natural asphalt.
Machines moving during the working process (e.g. mobile mastic asphalt mixers) and crushers are not covered by this European Standard.
Those types of asphalt mixing plants can also be combined or enlarged by additional installations (e.g. Plant for storage of binders (e.g. bituminous, synthetic, vegetal).
This European Standard deals with all significant hazards pertinent to mixing plants, when they are used as intended and under the conditions of misuse which are reasonably foreseen by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards.
This European Standard does not apply to machines for the production of cement concrete and mortar as covered in EN 12151.
This European Standard does not deal with hazards caused by flammable gases. As soon as information is available it will be included.
This European Standard is not applicable to mixing plants for road construction materials, which are manufactured before the date of publication of this European Standard by CEN.
- Standard60 pagesEnglish languagesale 10% offe-Library read for×1 day
- 29-Nov-2015
- 91.220
- 93.080.10
- 2006/42/EC
- M/396
- CEN/TC 151
This European Standard is applicable to tunnelling machinery as defined in Clause 3 used for the construction of tunnels, shafts and other underground excavations.
It deals with all significant hazards, hazardous situations and events relevant to such machinery when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
This European Standard covers monitoring for hazardous atmospheres within the confines of the tunnelling machinery.
Hand-arm and whole-body vibration are not considered as significant hazard for tunnelling machinery.
The following items and applications are not covered by this European Standard:
- The additional requirements for the use of tunnelling machinery under hyperbaric conditions;
- the additional requirements for use of tunnelling machinery in potentially explosive atmospheres;
NOTE For the application in potentially explosive atmospheres see EN 1710:2005+A1:2008 for guidance.
- ancillary tools and equipment which are not an integral part of the tunnelling machinery but used on or with the machinery;
- services (e.g. power supply, water, pipes, compressed air, etc.) supplied to the tunnelling machinery;
- loading and transport equipment which is not an integral part of the tunnelling machinery, e.g. man riders, locomotives, grout cars, segment cars, muck cars and shaft hoisting equipment.
This European Standard is not applicable to road headers, continuous miners and impact rippers.
This European Standard is not applicable to tunnelling machinery which is manufactured before the date of publication of this European Standard by CEN.
- Standard50 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft46 pagesEnglish languagesale 10% offe-Library read for×1 day
- 30-Aug-2014
- 29-Nov-2014
- 91.220
- 93.060
- 2006/42/EC
- M/396
- CEN/TC 151
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.