FprEN ISO 16810
(Main)Non-destructive testing - Ultrasonic testing - General principles (ISO/FDIS 16810:2024)
Non-destructive testing - Ultrasonic testing - General principles (ISO/FDIS 16810:2024)
ISO 16810:2012 defines the general principles required for the ultrasonic examination of industrial products that permit the transmission of ultrasound.
The specific conditions of application and use of ultrasonic examination, which depend on the type of product examined, are described in documents which could include: a) product standards; b) specifications; c) codes; d) contractual documents; e) written procedures.
Unless otherwise specified in the referencing documents the minimum requirements of ISO 16810:2012 are applicable.
ISO 16810:2012 does not define: 1) extent of examination and scanning plans; 2) acceptance criteria.
Zerstörungsfreie Prüfung - Ultraschallprüfung - Allgemeine Grundsätze (ISO/FDIS 16810:2024)
Essais non destructifs - Contrôle par ultrasons - Principes généraux (ISO/FDIS 16810:2024)
L'ISO 16810:2012 définit les principes généraux du contrôle ultrasonore des produits industriels perméables aux ondes ultrasonores.
Les conditions particulières d'application et d'utilisation des contrôles ultrasonores, qui dépendent du type de produit examiné, font l'objet de documents tels que normes de produit, spécifications, codes, documents contractuels et procédures écrites.
Sauf indications contraires dans les documents de référence, les exigences minimales de l'ISO 16810:2012 sont applicables.
L'ISO 16810:2012 ne définit pas l'étendue des essais et des plans de contrôle et les critères d'acceptation.
Neporušitvene preiskave - Ultrazvočne preiskave - Splošna načela (ISO/DIS 16810:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2024
Neporušitvene preiskave - Ultrazvočne preiskave - Splošna načela (ISO/DIS
16810:2024)
Non-destructive testing - Ultrasonic testing - General principles (ISO/DIS 16810:2024)
Zerstörungsfreie Prüfung - Ultraschallprüfung - Allgemeine Grundsätze (ISO/DIS
16810:2024)
Essais non destructifs - Contrôle par ultrasons - Principes généraux (ISO/DIS
16810:2024)
Ta slovenski standard je istoveten z: prEN ISO 16810
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT INTERNATIONAL STANDARD
ISO/DIS 16810
ISO/TC 135/SC 3 Secretariat: DIN
Voting begins on: Voting terminates on:
2024-01-23 2024-04-16
Non-destructive testing — Ultrasonic testing — General
principles
Essais non destructifs — Contrôle par ultrasons — Principes généraux
ICS: 19.100
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 16810:2024(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2024
ISO/DIS 16810:2024(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 16810
ISO/TC 135/SC 3 Secretariat: DIN
Voting begins on: Voting terminates on:
Non-destructive testing — Ultrasonic testing — General
principles
Essais non destructifs — Contrôle par ultrasons — Principes généraux
ICS: 19.100
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2024
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 16810:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
ISO/DIS 16810:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Qualification and certification of test personnel . 2
5 Information required prior to testing . 2
6 Principles of ultrasonic testing (UT) . .2
6.1 General . 2
6.2 Wave mode and direction of sound propagation . 3
6.3 Through-transmission technique . 3
6.4 Pulse-echo technique . . 3
7 Test equipment .3
7.1 Instrument . 3
7.2 Probes . 3
7.2.1 Probe selection. 4
7.2.2 Frequency and dimensions of transducer . 4
7.2.3 Dead zone . 4
7.2.4 Damping . 4
7.2.5 Focusing probes . 4
7.3 Coupling media . 5
7.4 Calibration blocks . 5
7.5 Reference blocks . 5
7.6 Specific test blocks . 6
8 Settings. 6
8.1 General . 6
8.2 Range . . 6
8.3 Sensitivity . 7
8.4 Pulse repetition frequency . 7
9 Preparation for testing . 7
9.1 Surface preparation . 7
9.2 Identification and datum points . 7
9.3 Application of transfer correction . 7
10 Testing. 8
10.1 Coverage of testing . 8
10.2 Overlapping . 8
10.3 Scanning speed. 8
10.4 Evaluation and recording levels . 8
10.4.1 General . 8
10.4.2 Pulse-echo technique . 9
10.4.3 Through-transmission technique . 9
11 Characterization of discontinuities .9
11.1 Pulse-echo technique . . 9
11.2 Through-transmission technique . 9
12 Test procedure .9
13 Test report .10
Bibliography .11
iii
ISO/DIS 16810:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information give
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.