EN ISO 16810:2014
(Main)Non-destructive testing - Ultrasonic testing - General principles (ISO 16810:2012)
Non-destructive testing - Ultrasonic testing - General principles (ISO 16810:2012)
ISO 16810:2012 defines the general principles required for the ultrasonic examination of industrial products that permit the transmission of ultrasound.
The specific conditions of application and use of ultrasonic examination, which depend on the type of product examined, are described in documents which could include: a) product standards; b) specifications; c) codes; d) contractual documents; e) written procedures.
Unless otherwise specified in the referencing documents the minimum requirements of ISO 16810:2012 are applicable.
ISO 16810:2012 does not define: 1) extent of examination and scanning plans; 2) acceptance criteria.
Zerstörungsfreie Prüfung - Ultraschallprüfung - Allgemeine Grundsätze (ISO 16810:2012)
Diese Internationale Norm legt die allgemeinen Grundsätze fest, die bei der Ultraschallprüfung von industriellen Erzeugnissen beachtet werden müssen, soweit sich Ultraschall in diesen Gegenständen ausbreiten kann.
Die besonderen Bedingungen der Anwendung und Durchführung von Ultraschallprüfungen, die von der Art des Prüfgegenstandes abhängen, sind in Dokumenten beschrieben, wie:
- Spezifikationen;
- Richtlinien;
- Regeln;
- vertragliche Vereinbarungen;
- schriftliche Prüfanweisungen.
Sofern in den zitierten Normen nichts anderes beschrieben ist, gelten die Mindestanaforderungen dieser Internationalen Norm.
Diese Norm behandelt nicht:
- Prüfumfang und Abtastpläne;
- Zulässigkeitskriterien.
Essais non destructifs - Contrôle par ultrasons - Principes généraux (ISO 16810:2012)
L'ISO 16810:2012 définit les principes généraux du contrôle ultrasonore des produits industriels perméables aux ondes ultrasonores.
Les conditions particulières d'application et d'utilisation des contrôles ultrasonores, qui dépendent du type de produit examiné, font l'objet de documents tels que normes de produit, spécifications, codes, documents contractuels et procédures écrites.
Sauf indications contraires dans les documents de référence, les exigences minimales de l'ISO 16810:2012 sont applicables.
L'ISO 16810:2012 ne définit pas l'étendue des essais et des plans de contrôle et les critères d'acceptation.
Neporušitvene preiskave - Ultrazvočne preiskave - Splošna načela (ISO 16810:2012)
Standard EN ISO 16810 opredeljuje splošna načela za ultrazvočne preiskave industrijskih izdelkov, ki omogočajo prenos ultrazvoka. Posebni pogoji izvajanja in uporabe ultrazvočnih preiskav, ki so odvisni od vrste izdelka, so opisani v dokumentih, med katerimi so lahko: - standardi izdelka; - specifikacije; - oznake; - pogodbeni dokumenti; - zapisani postopki. Minimalne zahteve tega mednarodnega standarda so veljavne, razen če je v referenčnih dokumentih drugače določeno.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2014
1DGRPHãþD
SIST EN 583-1:2000
SIST EN 583-1:2000/A1:2004
1HSRUXãLWYHQHSUHLVNDYH8OWUD]YRþQHSUHLVNDYH6SORãQDQDþHOD ,62
Non-destructive testing - Ultrasonic testing - General principles (ISO 16810:2012)
Zerstörungsfreie Prüfung - Ultraschallprüfung - Allgemeine Grundsätze (ISO
16810:2012)
Essais non destructifs - Contrôle par ultrasons - Principes généraux (ISO 16810:2012)
Ta slovenski standard je istoveten z: EN ISO 16810:2014
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 16810
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2014
ICS 19.100 Supersedes EN 583-1:1998
English Version
Non-destructive testing - Ultrasonic testing - General principles
(ISO 16810:2012)
Essais non destructifs - Contrôle par ultrasons - Principes Zerstörungsfreie Prüfung - Ultraschallprüfung - Allgemeine
généraux (ISO 16810:2012) Grundsätze (ISO 16810:2012)
This European Standard was approved by CEN on 9 February 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16810:2014 E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
The text of ISO 16810:2012 has been prepared by Technical Committee ISO/TC 135 “Non-destructive testing”
of the International Organization for Standardization (ISO) and has been taken over as EN ISO 16810:2014 by
Technical Committee CEN/TC 138 “Non-destructive testing” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2014, and conflicting national standards shall be
withdrawn at the latest by September 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 583-1:1998.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 16810:2012 has been approved by CEN as EN ISO 16810:2014 without any modification.
INTERNATIONAL ISO
STANDARD 16810
First edition
2012-04-01
Non-destructive testing — Ultrasonic
testing — General principles
Essais non destructifs — Contrôle par ultrasons — Principes généraux
Reference number
ISO 16810:2012(E)
©
ISO 2012
ISO 16810:2012(E)
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
ISO 16810:2012(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Qualification and certification of personnel .2
4 Information required prior to examination.2
5 Principles of ultrasonic examination.3
5.1 General.3
5.2 Vibration mode and direction of sound propagation .3
5.3 Transmission technique.3
5.4 Pulse echo technique.3
6 Equipment.4
6.1 Ultrasonic instrument.4
6.2 Ultrasonic probes.4
6.2.1 Probe selection.4
6.2.2 Frequency and dimensions of transducer.4
6.2.3 Dead zone.4
6.2.4 Damping.5
6.2.5 Focusing probes.5
6.3 Coupling media.5
6.4 Calibration blocks.5
6.5 Reference blocks.5
6.6 Specific blocks.6
7 Settings.6
7.1 General settings.6
7.2 Range settings.6
7.3 Amplification.7
7.4 Pulse repetition frequency .7
8 Preparation for examination.7
8.1 Surface preparation.7
8.2 Identification and datum points .7
8.3 Application of transfer correction .7
9 Examination.8
9.1 Examination coverage.8
9.2 Overlap and scanning speed .8
9.2.1 Overlap.8
9.2.2 Scanning speed.8
9.3 Evaluation and recording levels .8
9.3.1 Pulse echo technique.8
9.3.2 Transmission technique.8
10 Characterization of imperfections .8
10.1 Pulse echo technique.8
10.2 Transmission techniques.9
11 Examination procedure.9
12 Examination report.10
ISO 16810:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16810 was prepared by Technical Committee ISO/TC 135, Non-destructive testing, Subcommittee SC 3,
Ultrasonic testing.
iv © ISO 2012 – All rights reserved
ISO 16810:2012(E)
Introduction
This International Standard is based on EN 583-1:1998, Non-destructive testing — Ultrasonic examination —
Part 1: General principles.
The following International Standards are linked.
ISO 16810, Non-destructive testing — Ultrasonic testing — General principles
ISO 16811, Non-destructive testing — Ultrasonic testing — Sensitivity and range setting
ISO 16823, Non-destructive testing — Ultrasonic testing — Transmission technique
ISO 16826, Non-destructive testing — Ultrasonic testing — Examination for discontinuities perpendicular to
the surface
ISO 16827, Non-destructive testing — Ultrasonic testing — C
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.