iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 75-3:2004/AC:2006

(Corrigendum)

Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics (ISO 75-3:2004)

Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics (ISO 75-3:2004)

CMC - Incorrect titles registered

Kunststoffe - Bestimmung der Wärmeformbeständigkeitstemperatur - Teil 3: Hochbeständige härtbare Schichstoffe und langfaserverstärkte Kunststoffe (ISO 75-3:2004)

Plastiques - Détermination de la température de fléchissement sous charge - Partie 3: Stratifiés thermodurcissables à haute résistance et plastiques renforcés de fibres longues (ISO 75-3:2004)

Polimerni materiali - Določanje temperature upogiba pod obremenitvijo - 3. del: Duromerni laminati z visoko trdnostjo in z dolgimi vlakni ojačeni polimeri (ISO 75-3:2004)

General Information

Status
Published
Publication Date
11-Apr-2006
ICS
83.120 - Reinforced plastics
83.140.20 - Laminated sheets
Technical Committee
CEN/TC 249 - Plastics
Drafting Committee
CEN/TC 249 - Plastics
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
12-Apr-2006
Completion Date
12-Apr-2006
Ref Project
SIST EN ISO 75-3:2004/AC:2006 - Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics (ISO 75-3:2004)

Relations

Corrects
EN ISO 75-3:2004 - Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates (ISO 75-3:2004)
Effective Date
22-Dec-2008
Revised
prEN ISO 75-3 - Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics (ISO/DIS 75-3:2024)
Effective Date
18-Jan-2023

Buy Standard

EN ISO 75-3:2004/AC:2006EN ISO 75-3:2004/AC:2006
PreviousNext
Corrigendum
EN ISO 75-3:2004/AC:2006
English, French and German language
2 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoffe - Bestimmung der Wärmeformbeständigkeitstemperatur - Teil 3: Hochbeständige
härtbare Schichstoffe und langfaserverstärkte Kunststoffe (ISO 75-3:2004)Plastiques - Détermination de la température de fléchissement sous charge - Partie 3: Stratifiés thermodurcissables a haute résistance et plastiques renforcés de fibres longues (ISO 75-3:2004)Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics (ISO 75-3:2004)83.120Reinforced plastics83.080.10DuromeriThermosetting materialsICS:Ta slovenski standard je istoveten z:EN ISO 75-3:2004/AC:2006SIST EN ISO 75-3:2004/AC:2006en,fr,de01-julij-2006SIST EN ISO 75-3:2004/AC:2006SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 75-3:2004/ACApril 2006Avril 2006April 2006ICS 83.140.20; 83.120English versionVersion FrançaiseDeutsche FassungPlastics - Determination of temperature of deflection under load - Part 3:High-strength thermosetting laminates and long-fibre-reinforced plastics(ISO 75-3:2004)Plastiques - Détermination de latempérature de fléchissement sous charge- Partie 3: Stratifiés thermodurcissables àhaute résistance et plastiques renforcés defibres longues (ISO 75-3:2004)Kunststoffe - Bestimmung derWärmeformbeständigkeitstemperatur - Teil3: Hochfeste duroplastische Laminate undlangfaserverstärkte Kunststoffe (ISO 75-3:2004)This corrigendum becomes effective on 12 April 2006 for incorporation in the three official
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 75-3:2004(Main)
Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates (ISO 75-3:2004)
SIST EN ISO 75-3:2004

ISO 75-3:2004 specifies a method for the determination of the temperature of deflection under load of high-strength thermosetting laminates and compression-moulded long-fibre-reinforced plastics in which the fibre length is greater than 7,5 mm. The flexural stress used is not fixed, as in ISO 75-2, but is a fraction (1/1000) of the initial (room-temperature) flexural modulus of the material under test. This allows the method to be applied to materials with a wide range of flexural moduli.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14129:1997(Main)
Fibre-reinforced plastic composites - Determination of the in-plane shear stress/shear strain response, including the in-plane shear modulus and strength, by the +/- 45° tension test method (ISO 14129:1997)
SIST EN ISO 14129:1999

This International Standard specifies a procedure for determining the in-plane shear stress-shear strain, shear modulus and shear strength of fibre-reinforced plastic composites by the +/- 45° tension test method. The method is suitable f for use with the following materials: - thermoset and thermoplastic matrix laminates made from unidirectional layers and/or fabrics including unidirectional fabrics, with the fibres oriented at +/- 45° to the specimen axis. the lay-up shall be symmetrical and balanced about the specimen mid-plane.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN ISO 75-3(Main)
Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics (ISO/DIS 75-3:2024)
oSIST prEN ISO 75-3:2024

ISO 75-3:2004 specifies a method for the determination of the temperature of deflection under load of high-strength thermosetting laminates and compression-moulded long-fibre-reinforced plastics in which the fibre length is greater than 7,5 mm. The flexural stress used is not fixed, as in ISO 75-2, but is a fraction (1/1000) of the initial (room-temperature) flexural modulus of the material under test. This allows the method to be applied to materials with a wide range of flexural moduli.

  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 75-3:2004(Main)
Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates (ISO 75-3:2004)
SIST EN ISO 75-3:2004

ISO 75-3:2004 specifies a method for the determination of the temperature of deflection under load of high-strength thermosetting laminates and compression-moulded long-fibre-reinforced plastics in which the fibre length is greater than 7,5 mm. The flexural stress used is not fixed, as in ISO 75-2, but is a fraction (1/1000) of the initial (room-temperature) flexural modulus of the material under test. This allows the method to be applied to materials with a wide range of flexural moduli.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14129:1997(Main)
Fibre-reinforced plastic composites - Determination of the in-plane shear stress/shear strain response, including the in-plane shear modulus and strength, by the +/- 45° tension test method (ISO 14129:1997)
SIST EN ISO 14129:1999

This International Standard specifies a procedure for determining the in-plane shear stress-shear strain, shear modulus and shear strength of fibre-reinforced plastic composites by the +/- 45° tension test method. The method is suitable f for use with the following materials: - thermoset and thermoplastic matrix laminates made from unidirectional layers and/or fabrics including unidirectional fabrics, with the fibres oriented at +/- 45° to the specimen axis. the lay-up shall be symmetrical and balanced about the specimen mid-plane.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN ISO 75-3(Main)
Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics (ISO/DIS 75-3:2024)
oSIST prEN ISO 75-3:2024

ISO 75-3:2004 specifies a method for the determination of the temperature of deflection under load of high-strength thermosetting laminates and compression-moulded long-fibre-reinforced plastics in which the fibre length is greater than 7,5 mm. The flexural stress used is not fixed, as in ISO 75-2, but is a fraction (1/1000) of the initial (room-temperature) flexural modulus of the material under test. This allows the method to be applied to materials with a wide range of flexural moduli.

  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3379:2024(Main)
Leather - Determination of distension and strength of surface (Ball burst method) (ISO 3379:2024)
SIST EN ISO 3379:2025

This document specifies a test method for the determination of distension and strength of the leather grain or finished surface. This method is applicable to all flexible leathers and it is particularly suitable to determine the lastability of leathers for footwear uppers.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12007-5:2024(Main)
Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 5: Service lines - Specific functional requirements
SIST EN 12007-5:2025

This document describes the specific functional requirements for the transportation of gases (gaseous energy carriers) through service lines in addition to the general functional requirements of EN 12007 1 for:
a)   a maximum operating pressure (MOP) up to and including 16 bar;
b)   an operating temperature between −20 °C and +40 °C;
c)   gases and blends of gases which are in the gaseous state when conveyed in the gas pipeline infrastructure such as hydrogen, hydrogen rich, and methane rich gases, dimethyl ether (DME) and propane and butanes used for combustion and/or as feedstock, excluding steam and compressed air, where technical evaluation has ensured that operating conditions, constituents and properties of the gas do not affect the safe operation and maintenance of the service line.
It applies to their design, construction, commissioning, decommissioning, operation, maintenance, extension and other associated works including safety and environmental aspects. The service line is the physical asset comprising of pipework from the gas main branch saddle or top tee to the outlet of the distribution system operator’s nominated point(s) of delivery (for example: isolation valve, regulator, meter connection or combination of regulator and isolation valve).
This document does not apply retrospectively to installations before the publication date unless specifically stated.
Specific functional requirements for:
—   polyethylene pipelines are given in EN 12007 2;
—   steel pipelines are given in EN 12007 3;
—   polyamide (PA-U) pipelines are given in CEN/TS 12007 6;
—   pipework for buildings are given in EN 1775;
—   pressure regulating installations are given in EN 12279 or EN 12186;
—   pressure testing, commissioning and decommissioning are given in EN 12327;
—   safety management system (SMS) and pipeline integrity management system (PIMS) are given in EN 17649.
This document specifies common basic principles for gas infrastructure. Users of this document are expected to be aware that there can exist more detailed national standards and/or codes of practice in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of terms of additional requirements in legislation/regulation than in this document, CEN/TR 13737 (all parts) illustrates these terms.
CEN/TR 13737 gives:
—   description of legislations/regulations applicable in a member state;
—   if appropriate, more restrictive national requirements;
—   a national contact point for the latest information.

  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 18003:2024(Main)
Food authenticity - Determination of 16-O-Methylcafestol content of green and roasted coffee - HPLC-method
SIST EN 18003:2025

This document specifies a high-performance liquid chromatography (HPLC) method for determining the 16-O-Methylcafestol content in green and roasted coffee.
The method is suitable for a content of 40 mg/kg to 1 600 mg/kg of 16-O-Methylcafestol of green and roasted coffee, respectively. The collaborative study has shown that mass fractions also between 20 mg/kg to 40 mg/kg can be successfully analysed depending on the laboratory equipment.
The compliance assessment process is not part of this document.

  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17972:2024(Main)
Food authenticity - Food authenticity and fraud - Concepts, terms and definitions
SIST EN 17972:2025

This document provides technical definitions of terms relating to authenticity and fraud when referring to food products. All terms and definitions are in the context of food supply chains, but most of them can also be applied when referring to feed products and the feed supply chain.

  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day