iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

prEN 1776

(Main)

Gas infrastructure - Gas measuring systems - Functional requirements

Gas infrastructure - Gas measuring systems - Functional requirements

This document specifies functional requirements for the design, construction, testing,
commissioning/decommissioning, operation, maintenance and where appropriate calibration, together with suitable documented provisions for all new gas measuring systems and any major changes of existing systems.
This document also specifies accuracy classes of measuring systems and thresholds applicable to these classes. Demonstration of compliance is achieved through the selection, installation and operation of appropriate measurement instruments, together with suitable documented provisions for calculations. Examples of demonstration of compliance are provided for each accuracy class; however, they are not prescriptive solutions.
This document is applicable for gases of the 2nd gas family as classified in EN 437 and for hydrogen and its blends with gases of the 2nd gas family. This document can also be used as a guideline for 1st and 3rd family gases as classified in EN 437; however additional considerations should be taken with regard to the different constituents and physical characteristics of the gas family.
This document is not applicable for:
- raw or sour gases.
- gas measurement in CNG and hydrogen fuelling stations.
This document gives guidelines when installing and operating gas meters with additional functionalities (smart meters).
Unless otherwise specified all pressures used in this document are gauge pressures.
For associated pressure regulating systems the requirements of EN 12186 and/or EN 12279 apply.
For requirements on design, housing, lay-out, materials for components, construction, ventilation, venting and overall safety of gas measuring systems within the scope of this document, EN 15001, EN 12186, EN 12279 and/or EN 1775 apply additionally, where relevant.
This document specifies common basic principles for gas infrastructure. Users of this European Standard should be aware that more detailed national standards and/or codes of practice can exist in the CEN member countries.
This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this European Standard, national legislation/regulation takes precedence as illustrated in CEN/TR 13737 parts 1 and 2.
CEN/TR 13737 (all parts) gives:
   clarification of all legislation/regulations applicable in a member state;
   if appropriate, more restrictive national requirements;
   a national contact point for the latest information.

Gasinfrastruktur - Gasmesssysteme - Funktionale Anforderungen

Infrastructures gazières - Systèmes de mesure de gaz - Exigences fonctionnelles

Infrastruktura za plin - Merilni sistemi - Funkcionalne zahteve

General Information

Status
Not Published
Publication Date
18-Mar-2025
ICS
75.180.30 - Volumetric equipment and measurements
Technical Committee
CEN/TC 234 - Gas infrastructure
Drafting Committee
CEN/TC 234/WG 5 - Gas measuring
Current Stage
4020 - Submission to enquiry - Enquiry
Start Date
29-Aug-2024
Due Date
16-Apr-2024
Completion Date
29-Aug-2024
Mandate
M/017 - Standardization mandate to CEN in the field of equipment and installation for the transmission and distribution of gas
Ref Project
oSIST prEN 1776:2024 - Gas infrastructure - Gas measuring systems - Functional requirements

Relations

Revises
EN 1776:2015 - Gas infrastructure - Gas measuring systems - Functional requirements
Effective Date
28-Jan-2023

Buy Standard

prEN 1776:2024prEN 1776:2024
PreviousNext
Draft
prEN 1776:2024
English language
110 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-oktober-2024
Infrastruktura za plin - Merilni sistemi - Funkcionalne zahteve
Gas infrastructure - Gas measuring systems - Functional requirements
Gasinfrastruktur - Gasmesssysteme - Funktionale Anforderungen
Infrastructures gazières - Systèmes de mesure de gaz - Prescriptions fonctionnelles
Ta slovenski standard je istoveten z: prEN 1776
ICS:
75.180.30 Oprema za merjenje Volumetric equipment and
prostornine in merjenje measurements
91.140.40 Sistemi za oskrbo s plinom Gas supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2024
ICS 75.180.30 Will supersede EN 1776:2015
English Version
Gas infrastructure - Gas measuring systems - Functional
requirements
Infrastructures gazières - Systèmes de mesure de gaz - Gasinfrastruktur - Gasmesssysteme - Funktionale
Prescriptions fonctionnelles Anforderungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 234.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1776:2024 E
worldwide for CEN national Members.

Contents
European foreword . 7
Introduction . 8
1 Scope . 9
2 Normative references . 10
3 Terms and definitions . 12
4 General requirements . 19
4.1 General. 19
4.2 Safety and environment . 20
4.3 Quality and measurement management system . 20
5 Basic requirements for gas measuring systems . 20
5.1 General. 20
5.2 Classification of the gas measuring system . 21
5.2.1 General. 21
5.2.2 Minimum requirements Class A and Class B . 22
5.2.3 Minimum requirements Class C and Class D . 23
5.3 Gas measuring system modules . 23
6 Energy Determination . 24
6.1 General. 24
6.2 Requirements for measurements used in energy determination . 24
6.2.1 Base conditions . 24
6.2.2 Flow measurement . 24
6.2.3 Gross calorific value (GCV) . 25
6.3 Calculation method of energy using assigned GCV and P, T, Z values . 26
6.4 Calculation method of energy using an on-site CVDD and on-site PTZ-Conversion . 26
6.5 Calculation method of energy using an assigned GCV and PTZ-conversion . 27
6.6 Calculation method of energy using PT-Conversion and assigned GCV and Z value . 27
6.7 Calculation method of energy using T-Conversion and assigned GCV, and P, Z values
................................................................................................................................................................... 27
6.8 Gas temperature conversion . 27
6.9 Gas pressure conversion . 27
6.10 Compressibility conversion . 27
6.11 PTZ-conversion . 28
6.12 Uncertainty of energy determination . 28
7 Design of gas measuring system . 29
7.1 General. 29
7.2 Safety provision . 29
7.3 Housing . 29
7.4 Gas measuring station . 30
7.5 Gas measuring installation . 30
7.5.1 General. 30
7.5.2 Continuity of supply . 33
7.5.3 Gas meters . 33
7.5.4 Gas meters with additional functionalities and remotely operated valve . 34
7.6 Calorific value determination system . 34
7.6.1 General. 34
7.6.2 Sampling . 35
7.6.3 Provisions for calibration . 35
7.7 Gas pressure measurement . 35
7.7.1 General . 35
7.7.2 Gas pressure measurement Class A and Class B . 35
7.7.3 Gas pressure determination Class C and Class D . 36
7.8 Gas temperature measurement . 36
7.9 Conversion device . 37
7.10 Compression factor . 37
7.11 Pipework requirements . 37
7.11.1 For Class A and Class B measuring installation . 37
7.11.2 For Class C and Class D measuring installation . 38
7.12 Valves . 38
7.12.1 General . 38
7.12.2 By-pass. 38
7.13 Parallel meter runs . 38
7.14 Pulsations and vibrations . 39
7.14.1 General . 39
7.14.2 Pulsating effects related to specific flow meter types: . 40
7.15 Filter . 40
7.16 Gas conditioning, hydrate protection . 40
7.17 Duplication/redundancy of measuring instruments . 40
7.18 Venting. 41
7.19 Ventilation . 41
7.20 Odorants and/or additives . 41
7.21 Electromagnetic compatibility (EMC) . 41
7.22 Documented provisions . 41
7.22.1 General . 41
7.22.2 Data handling (Security) . 42
8 Construction of a gas measuring installation . 43
8.1 General . 43
8.2 Specific requirements for thermowells . 43
8.3 Specific requirements for (differential) pressure transducers . 43
8.4 Specific requirements for sampling systems for CVDD’s . 44
8.5 Corrosion protection . 44
8.6 Electrical equipment in hazardous area . 44
9 Testing of the gas measuring installation/station. 44
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 1776:2015(Main)
Gas infrastructure - Gas measuring systems - Functional requirements
SIST EN 1776:2016

This European Standard specifies functional requirements for the design, construction, testing, commissioning/decommissioning, operation, maintenance and where appropriate calibration, together with suitable documented provisions for all new gas measuring systems and any major changes of existing systems.
This European Standard also specifies accuracy classes of measuring systems and thresholds applicable to these classes. Demonstration of compliance is achieved through the selection, installation and operation of appropriate measurement instruments, together with suitable documented provisions for calculations. Examples of demonstration of compliance are provided for each accuracy class; however, they are not prescriptive solutions.
This European Standard is applicable for gases of the 2nd family as classified in EN 437. It is also applicable for treated non-conventional combustible gases complying with EN 437 and for which a detailed technical evaluation of the functional requirements (such as injected biomethane) is performed ensuring there are no other constituents or properties of the gases that can affect the metrological and physical integrity of the measuring systems.
This European Standard can also be used as a guideline for 1st and 3rd family gases as classified in EN 437; however additional considerations should be taken with regard to the different constituents and physical characteristics of the gas family.
This European Standard is not applicable for raw or sour gases.
This European Standard is not applicable for gas measurement in CNG filling station.
This European Standard gives guidelines when designing, installing and operating gas meters with additional functionalities (smart meters).
Unless otherwise specified all pressures used in this European Standard are gauge pressures.
For associated pressure regulating systems the requirements of EN 12186 and/or EN 12279 apply.
For requirements on design, housing, lay-out, materials for components, construction, ventilation, venting and overall safety of gas measuring systems within the scope of this European Standard, EN 15001, EN 12186, EN 12279 and/or EN 1775 apply additionally, where relevant.
This European Standard specifies common basic principles for gas infrastructure. Users of this European Standard should be aware that more detailed national standards and/or codes of practice may exist in the CEN member countries.
This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this European Standard, national legislation/regulation takes precedence as illustrated in CEN/TR 13737 parts 1 and 2.
CEN/TR 13737 (all parts) gives:
   clarification of all legislation/regulations applicable in a member state;
   if appropriate, more restrictive national requirements;
   a national contact point for the latest information.

  • Standard
    86 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 12185:2024(Main)
Crude petroleum, petroleum products and related products - Determination of density - Laboratory density meter with an oscillating U tube sensor (ISO 12185:2024)
SIST EN ISO 12185:2024

This document specifies a method for the determination, using an oscillating U-tube density meter, of the density of crude petroleum and related products within the range 600 kg/m3 to 1 100 kg/m3, which can be handled as single-phase liquids at the test temperature and pressure.
This document is applicable to liquids of any vapour pressure as long as suitable precautions are taken to ensure that they remain in single phase. Loss of light components leads to changes in density during both the sample handling and the density determination.
This method is not intended for use with in-line density meters.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 7278-2:2022(Main)
Petroleum measurement systems - Part 2: Pipe prover design, calibration and operation (ISO 7278-2:2022)
SIST EN ISO 7278-2:2023

This document provides descriptions of the different types of pipe provers, otherwise known as displacement provers, currently in use. These include sphere (ball) provers and piston provers operating in unidirectional and bidirectional forms. It applies to provers operated in conventional, reduced volume, and small volume modes.
This document gives guidelines for:
—    the design of pipe provers of each type;
—    the calibration methods;
—    the installation and use of pipe provers of each type;
—    the interaction between pipe provers and different types of flowmeters;
—    the calculations used to derive the volumes of liquid measured (see Annex A);
—    the expected acceptance criteria for fiscal and custody transfer applications, given as guidance for both the calibration of pipe provers and when proving flowmeters (see Annex C).
This document is applicable to the use of pipe provers for crude oils and light hydrocarbon products which are liquid at ambient conditions. The principles apply across applications for a wider range of liquids, including water. The principles also apply for low vapour pressure, chilled and cryogenic products, however use with these products can require additional guidance.

  • Standard
    118 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8222:2020/A1:2022(Amendment)
Petroleum measurement systems - Calibration - Volumetric measures, proving tanks and field measures (including formulae for properties of liquids and materials) - Amendment 1: Correction of two typographical errors (ISO 8222:2020/Amd 1:2022)
SIST EN ISO 8222:2020/A1:2022
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8222:2020(Main)
Petroleum measurement systems - Calibration - Volumetric measures, proving tanks and field measures (including formulae for properties of liquids and materials) (ISO 8222:2020)
SIST EN ISO 8222:2020

This document describes the design, use and calibration of volumetric measures (capacity measures) which are intended for use in fixed locations in a laboratory or in the field. This document gives guidance on both standard and non-standard measures. It also covers portable and mobile measures. This document is applicable to the petroleum industry; however, it may be applied more widely to other applications.
This document excludes measures for cryogenic liquids and pressurized measures as used for liquid petroleum gas (LPG) and liquefied natural gas (LNG).
Volumetric measures are classified as test measures or prover tanks depending on capacity and design.
Measures described in this document are primarily designed, calibrated and used to measure volumes from a measure which is wetted and drained for a specified time before use and designated to deliver. Many of the provisions, however, apply equally to measures which are used to measure a volume using a clean and dry measure and designated to contain.
Guidance is given regarding commonly expected uncertainties and calibration specifications.
The document also provides, in Annex A, reference formulae describing the properties of water and other fluids and materials used in volumetric measurement more generally.

  • Standard
    79 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1776:2015(Main)
Gas infrastructure - Gas measuring systems - Functional requirements
SIST EN 1776:2016

This European Standard specifies functional requirements for the design, construction, testing, commissioning/decommissioning, operation, maintenance and where appropriate calibration, together with suitable documented provisions for all new gas measuring systems and any major changes of existing systems.
This European Standard also specifies accuracy classes of measuring systems and thresholds applicable to these classes. Demonstration of compliance is achieved through the selection, installation and operation of appropriate measurement instruments, together with suitable documented provisions for calculations. Examples of demonstration of compliance are provided for each accuracy class; however, they are not prescriptive solutions.
This European Standard is applicable for gases of the 2nd family as classified in EN 437. It is also applicable for treated non-conventional combustible gases complying with EN 437 and for which a detailed technical evaluation of the functional requirements (such as injected biomethane) is performed ensuring there are no other constituents or properties of the gases that can affect the metrological and physical integrity of the measuring systems.
This European Standard can also be used as a guideline for 1st and 3rd family gases as classified in EN 437; however additional considerations should be taken with regard to the different constituents and physical characteristics of the gas family.
This European Standard is not applicable for raw or sour gases.
This European Standard is not applicable for gas measurement in CNG filling station.
This European Standard gives guidelines when designing, installing and operating gas meters with additional functionalities (smart meters).
Unless otherwise specified all pressures used in this European Standard are gauge pressures.
For associated pressure regulating systems the requirements of EN 12186 and/or EN 12279 apply.
For requirements on design, housing, lay-out, materials for components, construction, ventilation, venting and overall safety of gas measuring systems within the scope of this European Standard, EN 15001, EN 12186, EN 12279 and/or EN 1775 apply additionally, where relevant.
This European Standard specifies common basic principles for gas infrastructure. Users of this European Standard should be aware that more detailed national standards and/or codes of practice may exist in the CEN member countries.
This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this European Standard, national legislation/regulation takes precedence as illustrated in CEN/TR 13737 parts 1 and 2.
CEN/TR 13737 (all parts) gives:
   clarification of all legislation/regulations applicable in a member state;
   if appropriate, more restrictive national requirements;
   a national contact point for the latest information.

  • Standard
    86 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15970:2014(Main)
Natural gas - Measurement of properties - Volumetric properties: density, pressure, temperature and compression factor (ISO 15970:2008)
SIST EN ISO 15970:2014

ISO 15970:2008 gives requirements and procedures for the measurement of the properties of natural gas that are used mainly for volume calculation and volume conversion: density at reference and at operating conditions, pressure, temperature and compression factor.
Only those methods and instruments are considered that are suitable for field operation under the conditions of natural gas transmission and distribution, installed either in-line or on-line, and that do not involve the determination of the gas composition.
ISO 15970:2008 gives examples for currently used instruments that are available commercially and of interest to the natural gas industry.
The density at reference conditions (sometimes referred to as normal, standard or even base density) is required for conversion of volume data and can be used for other physical properties.
Density at operating conditions is measured for mass-flow measurement and volume conversion using the observed line density and can be used for other physical properties. ISO 15970:2008 covers density transducers based on vibrating elements, normally suitable for measuring ranges of 5 kg/m3 to 250 kg/m3.
Pressure measurement deals with differential, gauge and absolute pressure transmitters. It considers both analogue and smart transmitters (i.e. microprocessor based instruments) and, if not specified otherwise, the corresponding paragraphs refer to differential, absolute and gauge pressure transmitters without distinction.
Temperature measurements in natural gas are performed within the range of conditions under which transmission and distribution are normally carried out (253 K < T < 338 K). In this field of application, resistance thermometer detectors (RTD) are generally used.
The compression factor (also known as the compressibility factor or the real gas factor and given the symbol Z) appears, in particular, in equations governing volumetric metering. Moreover, the conversion of volume at metering conditions to volume at defined reference conditions can properly proceed with an accurate knowledge of Z at both relevant pressure and relevant temperature conditions.

  • Standard
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8311:2013(Main)
Refrigerated hydrocarbon and non-petroleum based liquefied gaseous fuels - Calibration of membrane tanks and independent prismatic tanks in ships - Manual and internal electro-optical distance-ranging methods (ISO 8311:2013)
SIST EN ISO 8311:2014

ISO 8311:2013 specifies a method for the internal measurement of membrane tanks used in ships for the transport of refrigerated light hydrocarbon fluids. In addition to the actual process of measurement, it sets out the calculation procedures for compiling the tank capacity table and correction tables to be used for the computation of cargo quantities. ISO 8311:2013, with some modification, can also be applicable to the calibration of independent prismatic tanks.

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 16478:2012(Main)
Surveillance from first commissioning on measuring devices used in natural gas supply to the installations of the activities under the Directive 2003/87/EC establishing a scheme of CO2 emissions trading
SIST-TP CEN/TR 16478:2013

This Technical Report establishes minimum provisions for the surveillance, based on available standards from first commissioning, of devices and systems with measuring function throughout their technical life when used in the activities of the categories listed in the Annex I of the European Directive 2003/87/EC. It does so in order to ensure the compliance with the expected maximum allowable difference of indication.
This Technical Report applies to devices/systems with the function to measure:
-   volumetric or mass amount of natural gas consumption (any type of gas meters),
-   volumetric amount of natural gas consumption at specified base conditions (conversion devices),
-   composition of natural gas (gas chromatographs),
for calculating, in accordance with the applicable provisions of the guidelines C(2007) 3416, the amount of the CO2 emissions from the source stream of natural gas.
Users of this document should be aware that more detailed national recommendations/standards and/or codes of practice as well as national measures possibly approved by National Regulator may exist inside the EU Member States.
When national regulations have to be applied, this document should not be considered.
Except in the aforementioned case, this Technical Report is intended to be applied in association with applicable national recommendations/standards and/or codes of practice setting out the above mentioned surveillance provisions.
In the event of conflict in terms of different requirements in national regulations/standards and in the provisions of this document, the national regulations/standards will take precedence.
Referring to the aforesaid Commission's guidelines C(2007) 3416, SFG_I opts for the calculation based method to determine the amount of the CO2 emissions.
Regarding commercially traded of natural gas, competent authorities may permit the determination of the annual gas consumption leading to evaluation of CO2 emissions based solely on the invoiced amount of gas without further individual proof of associated uncertainties, provided that national legislation or the documented application of standards ensures that respective uncertainty requirements for activity data are met for commercial transactions (guidelines C(2007) 3416 -annex 1 §7).
Referring to 5.2 and to Chapter 16, annex 1 of guidelines C(2007) 3416, for installations with “de minimis” souce streams and with low emissions respectively, the provisions of this document can be waived.

  • Technical report
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical report
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13352:2012(Main)
Specification for the performance of automatic tank contents gauges
SIST EN 13352:2012

This European Standard specifies the minimum performance requirements for various classes of automatic tank gauges which are limited to static tanks of shop fabricated manufacture both metallic and non metallic, underground and above ground which do not exceed 5 m in height.
It is applicable to gauges for fuels (products) which are flammable, having a flash point up to but not exceeding 100 C, stored at premises (e.g. filling stations) at which fuel is dispensed for use in vehicles and other forms of transportation. This European Standard applies to gauges suitable for use at ambient tempera¬tures and subject to normal operational pressure variations.
Gauging of liquefied gases are not covered by this standard.
This European Standard relates to the measurement of product level, measurement of product temperature and detection of the presence of free water. The detection of free water may be compromised for Alcohol blended fuels.
NOTE 1   This standard is not intended to cover safety functionalities (i.e. overfill prevention, leak detection, etc.). Further Standards apply.
NOTE 2    This standard is not intended to cover legal metrology requirements.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day