EN ISO 17491-3:2008
(Main)Protective clothing - Test methods for clothing providing protection against chemicals - Part 3: Determination of resistance to penetration by a jet of liquid (jet test) (ISO 17491-3:2008)
Protective clothing - Test methods for clothing providing protection against chemicals - Part 3: Determination of resistance to penetration by a jet of liquid (jet test) (ISO 17491-3:2008)
ISO 17491-3:2008 specifies a test method for determining the resistance of protective clothing against penetration by a jet of liquid.
ISO 17491-3:2008 is applicable to clothing with liquid-tight connections between different parts of the clothing and, if applicable, between the clothing and other items of personal protective equipment worn with it.
ISO 17491-3:2008 does not address chemical permeation resistance of the clothing materials, which is specified in other standards.
Schutzkleidung - Prüfverfahren für Chemikalienschutzkleidung - Teil 3: Bestimmung der Beständigkeit gegen das Durchdringen eines Flüssigkeitsstrahls (Jet-Test) (ISO 17491-3:2008)
Dieser Teil von ISOISO 17491 legt ein Prüfverfahren zur Bestimmung der Beständigkeit von Schutzkleidung gegen das Durch¬dringen eines Flüssigkeitsstrahls fest.
Dieser Teil von ISOISO 17491 gilt für Kleidung mit flüssigkeitsdichten Verbindungen zwischen verschiedenen Teilen der Kleidung und, sofern zutreffend, zwischen der Kleidung und gleichzeitig getragenen anderen Gegenständen persönlicher Schutzausrüstung.
Dieser Teil von ISOISO 17491 gilt nicht für die Beständigkeit gegen Permeation von Chemikalien durch Materialien, die in anderen Normen festgelegt ist.
Vêtements de protection - Méthodes d'essai pour les vêtements fournissant une protection contre les produits chimiques - Partie 3: Détermination de la résistance à la pénétration par un jet de liquide (essai au jet) (ISO 17491-3:2008)
L'ISO 17491-3:2008 spécifie une méthode d'essai pour la détermination de la résistance à la pénétration par un jet de liquide des vêtements de protection.
L'ISO 17491-3:2008 s'applique aux vêtements ayant des coutures étanches entre les différentes parties du vêtement, et, le cas échéant, entre le vêtement et les autres équipements de protection individuelle portés en association.
L'ISO 17491-3:2008 ne traite pas de la résistance à la perméation chimique des matériaux du vêtement, spécifiée dans d'autres normes.
Varovalna obleka - Preskusne metode za obleke, ki varujejo pred kemikalijami - 3. del: Ugotavljanje odpornosti proti penetraciji curka tekočine (jet test) (ISO 17491-3:2008)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Schutzkleidung - Prüfverfahren für Chemikalienschutzkleidung - Teil 3: Bestimmung der Beständigkeit gegen das Durchdringen eines Flüssigkeitsstrahls (Jet-Test) (ISO 17491-3:2008)Vetements de protection - Méthodes d'essai pour les vetements fournissant une protection contre les produits chimiques - Partie 3: Détermination de la résistance a la pénétration par un jet de liquide (essai au jet) (ISO 17491-3:2008)Protective clothing - Test methods for clothing providing protection against chemicals - Part 3: Determination of resistance to penetration by a jet of liquid (jet test) (ISO 17491-3:2008)13.340.10Varovalna oblekaProtective clothingICS:Ta slovenski standard je istoveten z:EN ISO 17491-3:2008SIST EN ISO 17491-3:2008en01-december-2008SIST EN ISO 17491-3:2008SLOVENSKI
STANDARDSIST EN 463:19961DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 17491-3August 2008ICS 13.340.10Supersedes EN 463:1994
English VersionProtective clothing - Test methods for clothing providingprotection against chemicals - Part 3: Determination ofresistance to penetration by a jet of liquid (jet test) (ISO 17491-3:2008)Vêtements de protection - Méthodes d'essai pour lesvêtements fournissant une protection contre les produitschimiques - Partie 3: Détermination de la résistance à lapénétration par un jet de liquide (essai au jet) (ISO 17491-3:2008)Schutzkleidung - Prüfverfahren fürChemikalienschutzkleidung - Teil 3: Bestimmung derBeständigkeit gegen das Durchdringen einesFlüssigkeitsstrahls (Jet-Test) (ISO 17491-3:2008)This European Standard was approved by CEN on 14 August 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 17491-3:2008: ESIST EN ISO 17491-3:2008
Relationship between this part of ISO 17491 and the Essential Requirements of EU Directive 89/686/EEC Personal Protective Equipment.4
Relationship between this part of ISO 17491 and the Essential Requirements of EU Directive 89/686/EEC Personal Protective Equipment This part of ISO 17491 has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide one means of conforming to Essential Requirements of the New Approach Directive 89/686/EEC.
Once this part of ISO 17491 is cited in the Official Journal of the European Communities under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of this standard, together with the relevant requirements given in the product standards, confers, within the limits of the scope of both standards, a presumption of conformity with the Essential Requirements of Directive 89/686/EEC Personal Protective Equipment, Annex II, Clause 3.10.2.
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard.
Reference numberISO 17491-3:2008(E)© ISO 2008
INTERNATIONAL STANDARD ISO17491-3First edition2008-08-15Protective clothing — Test methods for clothing providing protection against chemicals — Part 3: Determination of resistance to penetration by a jet of liquid (jet test) Vêtements de protection — Méthodes d'essai pour les vêtements fournissant une protection contre les produits chimiques — Partie 3: Détermination de la résistance à la pénétration par un jet de liquide (essai au jet)
ISO 17491-3:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2008 – All rights reserved
ISO 17491-3:2008(E) © ISO 2008 – All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 17491-3 was prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 162, Protective clothing including hand and arm protection and lifejackets, in collaboration with Technical Committee ISO/TC 94, Personal safety — Protective clothing and equipment, Subcommittee SC 13, Protective clothing, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). This first edition of ISO 17491-3, together with ISO 17491-4, cancels and replaces ISO 17491:2002, Clauses 6 and 7 of which have been technically revised. ISO 17491 consists of the following parts, under the general title Protective clothing — Test methods for clothing providing protection against chemicals: ⎯ Part 3: Determination of resistance to penetration by a jet of liquid (jet test) ⎯ Part 4: Determination of resistance to penetration by a spray of liquid (spray test) The following parts are under development: ⎯ Part 1: Determination of resistance to outward leakage of gases (internal pressure test) ⎯ Part 2: Determination of resistance to inward leakage of aerosols and gases (inward leakage test) SIST EN ISO 17491-3:2008
ISO 17491-3:2008(E) iv © ISO 2008 – All rights reserved Introduction This part of ISO 17491 describes a test method for determining the liquid penetration resistance of chemical protective clothing Type 3 (with liquid-tight connections between different parts of the clothing and, if applicable, between the clothing and other items of personal protective equipment). Such clothing comprises one or more items covering the full surface of the body and is intended to be worn under conditions where there is a risk of exposure to a forceful projection of a liquid chemical. Interlaboratory testing has shown that this test method is a repeatable pass/fail method. Other requirements with regard to this type of clothing and its constituent materials can be found in the corresponding product standard (see Bibliography [2]). A document on the selection, use and maintenance of chemical protective clothing is available (see Bibliography [3]). CAUTION — Some of the procedures specified in this part of ISO 17491 involve the use of processes which could lead to hazardous situations and hence appropriate precautions should be taken.
INTERNATIONAL STANDARD ISO 17491-3:2008(E) © ISO 2008 – All rights reserved 1 Protective clothing — Test methods for clothing providing protection against chemicals — Part 3: Determination of resistance to penetration by a jet of liquid (jet test) 1 Scope This part of ISO 17491 specifies a test method for determining the resistance of protective clothing against penetration by a jet of liquid. This part of ISO 17491 is applicable to clothing with liquid-tight connections between different parts of the clothing and, if applicable, between the clothing and other items of personal protective equipment worn with it. This part of ISO 17491 does not address chemical permeation resistance of the clothing materials, which is specified in other standards. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/TR 11610, Protective clothing — Vocabulary 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO/TR 11610 and the following apply. 3.1 connection assemblage or join 3.2 calibrated stain fluorescent or visible stain, with a defined minimum area, generated by dropping a specified quantity of test liquid on to an absorbent overall NOTE The calibrated stain is used to measure liquid penetration during spray and jet testing of chemical protective clothing. 3.3 absorbent overall overall made from an absorbent material, worn under the test suit and intended for collecting liquid penetration during spray and jet testing of chemical protective clothing SIST EN ISO 17491-3:2008
ISO 17491-3:2008(E) 2 © ISO 2008 – All rights reserved 4 Principle of the test method A water jet, containing a fluorescent or visible dye tracer, is directed at chemical protective clothing worn by a human test subject. Inspection of the inside surface of the clothing and the outside surface of the absorbent overall, worn under the protective clothing, allows any points of inward leakage to be identified. 5 Liquid for application in the form of a jet A test liquid containing the following substances shall be used: ⎯ water at (20 ± 2) °C; ⎯ a water-soluble fluorescent or visible dye, e.g. methyl blue (CAS number [28983-56-4]); ⎯ a surfactant, e.g. Genapol LRO liquid (sodium lauryl ether sulphate, CAS number [009004-82-4]); ⎯ a stabilizer for the dye (if needed), e.g. citric acid (CAS number [77-92-9], analytical grade). Prepare the test liquid by dissolving the dye in water. Add the surfactant and the dye stabilizer (if needed) in the appropriate proportions to obtain a solution with a surface tension of (30 ± 5) × 10−3 N/m. NOTE A typical concentrated solution can be made by dissolving 4 g methyl blue, 25 ml Genapol LRO liquid and 125 g citric acid in 1 l of tap water. The mixture is stirred for 15 min to 20 min with a magnetic stirrer and eventually 200 ml of it is diluted in 10 l of water. To measure the surface tension within the stated toleran
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.