EN 14175-3:2003
(Main)Fume cupboards - Part 3: Type test methods
Fume cupboards - Part 3: Type test methods
Part 5 of this European Standard specifies type test methods for the assessment of safety, robustness and performance of fume cupboards.
Abzüge - Teil 3: Baumusterprüfverfahren
Anwendungsbereich
Dieser Teil der Europäischen Norm EN 14175 legt Baumusterprüfverfahren zur Bewertung der Sicherheit und des Leistungsvermögens von Frontschieber und Luftströmung von Abzügen fest. Die entsprechenden Anforderungen sind in Teil 2 von EN 14175 festgelegt.
Für Begriffe zu Abzügen gilt EN 14175-1. Für Sicherheits- und Leistungsanforderungen gilt EN 14175-2.
ANMERKUNG Teil 4 dieser Europäischen Norm für die Vor-Ort Prüfung von im Labor installierten Abzügen befindet sich in Vorbereitung.
Für die Prüfung von mikrobiologischen Sicherheitswerkbänken gilt EN 12469.
Sorbonnes - Parite 3: Méthodes d'essai de type
La présente partie de la norme européenne EN 14175 spécifie les méthodes d'essai de type pour l'évaluation de la sécurité et des performances des sorbonnes. La partie 2 de la présente Norme européenne spécifie des exigences pertinentes.
Pour les termes et leurs définitions, l'EN 14175-1 s'applique. Pour les exigences de sécurité et de performances des sorbonnes, l'EN 14175-2 s'applique.
NOTE La partie 4 de la présente Norme européenne est en préparation pour les méthodes d'essai sur site des sorbonnes.
Pour les essais des postes de sécurité microbiologique, l'EN 12469 s'applique.
Fume cupboards - Part 3: Type test methods
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Fume cupboards - Part 3: Type test methodsFume cupboards - Part 3: Type test methodsSorbonnes - Parite 3: Méthodes d'essai de typeAbzüge - Teil 3: Baumusterprüfverfahren71.040.10Kemijski laboratoriji. Laboratorijska opremaChemical laboratories. Laboratory equipmentICS:SIST EN 14175-3:2004enTa slovenski standard je istoveten z:EN 14175-3:200301-februar-2004SIST EN 14175-3:2004SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14175-3December 2003ICS 71.040.10English versionFume cupboards - Part 3: Type test methodsSorbonnes - Parite 3: Méthodes d'essai de typeAbzüge - Teil 3: BaumusterprüfverfahrenThis European Standard was approved by CEN on 1 October 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14175-3:2003 E
EN 14175-3:2003 (E)2ContentspageForeword.3Introduction.41Scope.52Normative references.53Terms and definitions.53.1plane of sash.53.2inner measurement plane.53.3containment factor (CF).64Test room and general test conditions.64.1Dimensions and construction.64.2Test room conditions.64.3Fume cupboard installation.64.4Test conditions.65Air flow tests.75.1Extract volume flow rate.75.2Face velocity.75.3Containment.85.4Robustness of containment.145.5Air exchange efficiency.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.