Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 5: Cut steel wire (ISO 11124-5:2019)

This document specifies requirements for 13 grades of cut steel wire abrasives, as supplied for blast-cleaning processes. It specifies ranges of particle sizes, together with corresponding grade designations. Values are specified for hardness, density, defect/structural requirements, metallographic structure and chemical composition.
This document is suitable for cut steel wire supplied for blast-cleaning processes which is made by cutting new cold drawn wire.
The requirements specified in this document apply to abrasives manufactured from virgin wire supplied in the new and unconditioned state only. They do not apply to abrasives either during or after use.
NOTE 1    Information on commonly referenced national standards for cut steel wire abrasives and their approximate relationship with ISO 11124 is given in Annex A.
NOTE 2    Although this document has been developed specifically to meet requirements for preparation of steelwork, the properties specified will generally be appropriate for use when preparing other material surfaces, or components, using blast-cleaning techniques.

Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen - Anforderungen an metallische Strahlmittel - Teil 5: Stahldrahtschrot (ISO 11124-5:2019)

Dieses Dokument legt Anforderungen an 13 Klassen von im Lieferzustand befindlichen Stahldrahtschrot-Strahlmitteln für Strahlprozesse fest. Zusammen mit Bezeichnungen für die entsprechenden Klassen legt es Korngrößenbereiche fest. Für die Härte, die Dichte, die Anforderungen hinsichtlich Defekten/Struktur, das metallographische Gefüge und die chemische Zusammensetzung werden Werte angegeben.
Dieses Dokument ist anwendbar auf Stahldrahtschrot, der für Strahlprozesse geliefert wird, der durch Schneiden von neuem kaltgezogenem Draht hergestellt ist.
Die in diesem Dokument festgelegten Anforderungen sind nur anzuwenden für unbehandelte neue Strahlmittel, die aus fabrikneuem Draht hergestellt sind. Sie sind nicht anzuwenden für Strahlmittel während oder nach der Verwendung.
ANMERKUNG 1 Informationen zu üblicherweise herangezogenen nationalen Normen für Strahlmittel aus Stahldrahtschrot und die Näherungsbeziehung dieser Normen zu ISO 11124 sind im Anhang A angegeben.
ANMERKUNG 2 Obwohl dieses Dokument speziell dafür ausgearbeitet worden ist, die Anforderungen an die Vorbereitung von Stahlbauteilen zu erfüllen, treffen die festgelegten Eigenschaften in der Regel auch auf die Vorbereitung von Oberflächen oder Bauteilen aus anderen Werkstoffen mit Strahlverfahren zu.

Préparation des subjectiles d'acier avant application de peintures et de produits assimilés - Spécifications pour préparation par projection d'abrasifs métalliques - Partie 5: Fils d'acier coupés (ISO 11124-5:2019)

Le présent document spécifie des exigences pour 13 granulométries d'abrasifs en fils d’acier coupés tels qu'ils sont fournis pour la préparation par projection. Il spécifie les gammes de tailles de particules, ainsi que les désignations de granulométrie correspondantes. Des valeurs sont spécifiées pour la dureté, la masse volumique, les exigences relatives aux défauts structuraux, la structure métallographique et la composition chimique.
Le présent document est adapté aux fils d’acier coupés fournis pour la préparation par projection, fabriqués par découpe à partir de fils tréfilés à froid neufs.
Les exigences spécifiées dans le présent document s’appliquent aux abrasifs fabriqués à partir de fils vierges fournis à l’état neuf et non conditionné uniquement. Elles ne s'appliquent pas aux abrasifs pendant ou après utilisation.
NOTE 1        L’Annexe A donne des informations sur les normes nationales généralement consultables portant sur les abrasifs en fils d’acier coupés, en relation avec l’ISO 11124.
NOTE 2        Le présent document été spécialement élaboré pour satisfaire aux exigences de préparation des ouvrages en acier; cependant, les propriétés prescrites sont généralement appropriées à la préparation de subjectiles ou éléments d'autres matériaux, par les techniques de décapage par projection.

Priprava jeklenih podlag pred nanašanjem barv in sorodnih premazov - Specifikacije za kovinske granulate za peskanje - 5. del: Sekana jeklena žica (ISO 11124-5:2019)

General Information

Status
Published
Publication Date
13-Apr-2021
Withdrawal Date
30-Oct-2021
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
14-Apr-2021
Due Date
09-Jun-2022
Completion Date
14-Apr-2021

Buy Standard

Standard
EN ISO 11124-5:2021
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 11124-5:2020
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11124-5:2021
01-julij-2021
Priprava jeklenih podlag pred nanašanjem barv in sorodnih premazov -
Specifikacije za kovinske granulate za peskanje - 5. del: Sekana jeklena žica (ISO
11124-5:2019)
Preparation of steel substrates before application of paints and related products -
Specifications for metallic blast-cleaning abrasives - Part 5: Cut steel wire (ISO 11124-
5:2019)
Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen -
Anforderungen an metallische Strahlmittel - Teil 5: Stahldrahtschrot (ISO 11124-5:2019)
Préparation des subjectiles d'acier avant application de peintures et de produits
assimilés - Spécifications pour préparation par projection d'abrasifs métalliques - Partie
5: Fils d'acier coupés (ISO 11124-5:2019)
Ta slovenski standard je istoveten z: EN ISO 11124-5:2021
ICS:
25.220.10 Priprava površine Surface preparation
87.020 Postopki za nanašanje Paint coating processes
barvnih premazov
SIST EN ISO 11124-5:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 11124-5:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 11124-5:2021


EN ISO 11124-5
EUROPEAN STANDARD

NORME EUROPÉENNE

April 2021
EUROPÄISCHE NORM
ICS 25.220.10
English Version

Preparation of steel substrates before application of paints
and related products - Specifications for metallic blast-
cleaning abrasives - Part 5: Cut steel wire (ISO 11124-
5:2019)
Préparation des subjectiles d'acier avant application de Vorbereitung von Stahloberflächen vor dem Auftragen
peintures et de produits assimilés - Spécifications pour von Beschichtungsstoffen - Anforderungen an
préparation par projection d'abrasifs métalliques - metallische Strahlmittel - Teil 5: Stahldrahtschrot (ISO
Partie 5: Fils d'acier coupés (ISO 11124-5:2019) 11124-5:2019)
This European Standard was approved by CEN on 5 April 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11124-5:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 11124-5:2021
EN ISO 11124-5:2021 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 11124-5:2021
EN ISO 11124-5:2021 (E)
European foreword
The text of ISO 11124-5:2019 has been prepared by Technical Committee ISO/TC 35 "Paints and
varnishes” of the International Organization for Standardization (ISO) and has been taken over as
EN ISO 11124-5:2021 by Technical Committee CEN/TC 139 “Paints and varnishes” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2021, and conflicting national standards shall
be withdrawn at the latest by October 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, M
...

SLOVENSKI STANDARD
oSIST prEN ISO 11124-5:2020
01-december-2020
Priprava jeklenih podlag pred nanašanjem barv in sorodnih premazov -
Specifikacije za kovinske granulate za peskanje - 5. del: Kroglice (shot) iz jeklene
žice (ISO 11124-5:2019)
Preparation of steel substrates before application of paints and related products -
Specifications for metallic blast-cleaning abrasives - Part 5: Steel cut wire shot (ISO
11124-5:2019)
Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen -
Anforderungen an metallische Strahlmittel - Teil 5: Stahldrahtschrot (ISO 11124-5:2019)
Préparation des subjectiles d'acier avant application de peintures et de produits
assimilés - Spécifications pour préparation par projection d'abrasifs métalliques - Partie
5: Fils d'acier coupés (ISO 11124-5:2019)
Ta slovenski standard je istoveten z: prEN ISO 11124-5:2020
ICS:
25.220.10 Priprava površine Surface preparation
87.020 Postopki za nanašanje Paint coating processes
barvnih premazov
oSIST prEN ISO 11124-5:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 11124-5:2020

---------------------- Page: 2 ----------------------
oSIST prEN ISO 11124-5:2020
INTERNATIONAL ISO
STANDARD 11124-5
First edition
2019-06
Preparation of steel substrates before
application of paints and related
products — Specifications for metallic
blast-cleaning abrasives —
Part 5:
Cut steel wire
Préparation des subjectiles d'acier avant application de peintures
et de produits assimilés — Spécifications pour préparation par
projection d'abrasifs métalliques —
Partie 5: Fils d'acier coupés
Reference number
ISO 11124-5:2019(E)
©
ISO 2019

---------------------- Page: 3 ----------------------
oSIST prEN ISO 11124-5:2020
ISO 11124-5:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 11124-5:2020
ISO 11124-5:2019(E)

Contents Page
Foreword .iv
1 Scope . 1
2  Normative references . 1
3  Terms and definitions . 2
4 Designation of abrasives . 3
5  Sampling . 3
6  Requirements for cut steel wire abrasives . 4
7  Package identification and lot traceability . 4
8  Information to be provided by the manufacturer or supplier . 5
Annex A (informative) Approximately equivalent codings for cut steel wire abrasives .6
Bibliography . 7
© ISO 2019 – All rights reserved iii

---------------------- Page: 5 -------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.