prEN ISO 105-X11
(Main)Textiles - Tests for colour fastness - Part X11: Colour fastness to hot pressing (ISO/DIS 105-X11:2024)
Textiles - Tests for colour fastness - Part X11: Colour fastness to hot pressing (ISO/DIS 105-X11:2024)
Tests are given for hot pressing when the textile is dry, when it is wet, and when it is damp. The end-use of the textile usually determines which test should be made. A dry specimen (dry pressing) or a dry specimen covered with a wet cotton adjacent fabric (damp pressing) or a wet specimen covered with a wet cotton adjacent fabric (wet pressing) are pressed with a heating device at a specified temperature and pressure for a specified time.
Textilien - Farbechtheitsprüfungen - Teil X11: Bestimmung der Farbechtheit gegen Bügeln (ISO/DIS 105-X11:2024)
Textiles - Essais de solidité des coloris - Partie X11: Solidité des coloris au pressage à chaud (ISO/DIS 105-X11:2024)
1.1 La présente partie de l'ISO 105 prescrit une méthode pour la détermination de la résistance des teintures sur les textiles de toute nature, à tous leurs stades de transformation, au repassage ou au traitement industriel sur cylindres chauds. 1.2 Des essais sont prévus pour le repassage à chaud lorsque le textile est sec, lorsqu'il est mouillé et lorsqu'il est humide. La destination finale du textile détermine généralement quel essai doit être effectué.
Tekstilije - Preskušanje barvne obstojnosti - Del X11: Barvna obstojnost pri vročem likanju (ISO/DIS 105-X11:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2024
Tekstilije - Preskušanje barvne obstojnosti - Del X11: Barvna obstojnost pri
vročem likanju (ISO/DIS 105-X11:2024)
Textiles - Tests for colour fastness - Part X11: Colour fastness to hot pressing (ISO/DIS
105-X11:2024)
Textilien - Farbechtheitsprüfungen - Teil X11: Bestimmung der Farbechtheit gegen
Bügeln (ISO/DIS 105-X11:2024)
Textiles - Essais de solidité des coloris - Partie X11: Solidité des coloris au pressage à
chaud (ISO/DIS 105-X11:2024)
Ta slovenski standard je istoveten z: prEN ISO 105-X11
ICS:
59.080.01 Tekstilije na splošno Textiles in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
International
Standard
ISO/DIS 105-X11
ISO/TC 38/SC 1
Textiles — Tests for colour
Secretariat: BSI
fastness —
Voting begins on:
Part X11: 2024-09-02
Colour fastness to hot pressing
Voting terminates on:
2024-11-25
Textiles — Essais de solidité des teintures —
Partie X11: Solidité des teintures au repassage à chaud
ICS: 59.080.01
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 105-X11:2024(en)
DRAFT
ISO/DIS 105-X11:2024(en)
International
Standard
ISO/DIS 105-X11
ISO/TC 38/SC 1
Textiles — Tests for colour
Secretariat: BSI
fastness —
Voting begins on:
Part X11:
Colour fastness to hot pressing
Voting terminates on:
Textiles — Essais de solidité des teintures —
Partie X11: Solidité des teintures au repassage à chaud
ICS: 59.080.01
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
This document is circulated as received from the committee secretariat. BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 105-X11:2024(en)
ii
ISO/DIS 105-X11:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
4.1 Dry pressing .1
4.2 Damp pressing .2
4.3 Wet pressing .2
4.4 Assessment .2
5 Apparatus . 2
6 Test specimen . 3
7 Procedure . 3
7.1 General .3
7.2 Dry pressing .3
7.3 Damp pressing .3
7.4 Wet pressing .4
7.5 Assessment .4
8 Test report . 4
iii
ISO/DIS 105-X11:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee [or Project Committee] ISO/TC 38, Textiles,
Subcommittee SC 1, Tests for coloured textiles and colorants.
This fifth edition cancels and replaces the fo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.