CEN/TS 15185:2005
(Main)Furniture - Assessment of the surface resistance to abrasion
Furniture - Assessment of the surface resistance to abrasion
This Technical Specification specifies a method for the assessment of the abrasion resistance of surfaces referred to under 7.4.
It does not apply to finishes on leather and fabrics.
It does not apply to the surfaces covered by EN 14434.
The test is intended to be carried out on finished furniture, but can be carried out on test panels of the same material, finished in an identical manner to the finished product, and on a size sufficient to meet the requirements of the test.
It is essential that the test be carried out on unused surfaces.
Möbel - Bewertung der Abriebfestigkeit von Oberflächen
Diese Technische Spezifikation legt ein Verfahren für die Bewertung der Abriebfestigkeit von Folien, Lamina-ten
und melamin-beschichteten Platten sowie Klarlacken oder pigmentierten Lacken fest.
Sie gilt nicht für behandelte Oberflächen aus Leder und Textilien.
Sie gilt nicht für die Oberflächen von Wandtafeln nach EN 14434.
Die Prüfung ist im Allgemeinen am gebrauchsfertigen Möbel durchzuführen, kann aber auch an Prüfkörpern
durchgeführt werden, die aus dem gleichen Werkstoff mit identischer Oberflächenbehandlung wie das fertige
Erzeugnis gefertigt wurden und groß genug sind, um den Anforderungen der Prüfung zu entsprechen.
Die Prüfung ist in jedem Fall an unbenutzten Oberflächen durchzuführen.
Ameublement - Evaluation de la résistance de la surface à l'abrasion
La présente Spécification technique prescrit une méthode d’évaluation de la résistance à l’abrasion des
panneaux stratifiés, surfacés, mélaminés ou revêtus de films ainsi que des vernis ou laques.
Elle ne s’applique pas aux finitions appliquées sur le cuir et les textiles.
Elle ne s’applique pas aux surfaces traitées dans l’EN 14434.
L’essai est destiné à être réalisé sur des meubles finis mais il peut être effectué sur des panneaux d’essai de
dimensions suffisantes pour satisfaire aux spécifications de l'essai et du même matériau et de finition
identique au meuble fini.
Il est essentiel que l’essai soit réalisé sur des surfaces neuves.
Pohištvo – Ugotavljanje odpornosti površine proti obrabi
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN/TS 15185:2006
01-februar-2006
Pohištvo – Ugotavljanje odpornosti površine proti obrabi
Furniture - Assessment of the surface resistance to abrasion
Möbel - Bewertung der Abriebfestigkeit von Oberflächen
Ameublement - Evaluation de la résistance de la surface a l'abrasion
Ta slovenski standard je istoveten z: CEN/TS 15185:2005
ICS:
97.140 Pohištvo Furniture
SIST-TS CEN/TS 15185:2006 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 15185:2006
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 15185:2006
TECHNICAL SPECIFICATION
CEN/TS 15185
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
November 2005
ICS 97.140
English Version
Furniture - Assessment of the surface resistance to abrasion
Ameublement - Evaluation de la résistance de la surface à Möbel - Bewertung der Abriebfestigkeit von Oberflächen
l'abrasion
This Technical Specification (CEN/TS) was approved by CEN on 1 October 2005 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 15185:2005: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 15185:2006
CEN/TS 15185:2005 (E)
Contents page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions.4
4 Principle.5
5 Apparatus and materials .5
6 Preparation and conditioning .6
7 Procedure .7
8 Assessment of results.8
9 Marking, labelling and packaging.9
Bibliography.10
2
---------------------- Page: 4 ----------------------
SIST-TS CEN/TS 15185:2006
CEN/TS 15185:2005 (E)
Foreword
This Technical Specification (CEN/TS 15185:2005) has been prepared by Technical Committee CEN/TC 207
“Furniture”, the secretariat of which is held by UNI.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this CEN Technical Specification: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST-TS CEN/TS 15185:2006
CEN/TS 15185:2005 (E)
1 Scope
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.