FprEN 14570

LPG equipment and accessories - Equipping of overground and underground LPG vessels

This European Standard specifies requirements for the equipping of LPG pressure vessels, overground and underground, with a volume not greater than 13 m3 manufactured in accordance with EN 12542 or equivalent and have been hydraulically tested.
The equipment covered by this European Standard is directly mounted onto the pressure vessel connections.
This European Standard excludes the equipping of depot storage vessels and refrigerated storage vessels.

Flüssiggas-Geräte und Ausrüstungsteile - Ausrüstung von oberirdisch und unterirdisch aufgestellten Behältern für Flüssiggas (LPG)

Équipements pour GPL et leurs accessoires - Équipement des réservoirs sous pression GPL aériens et enterrés

Oprema in pribor za utekočinjeni naftni plin (UNP) - Oprema za nadzemne in podzemne posode za UNP

General Information

• Status: Not Published
• Publication Date: 16-Aug-2023
• ICS: 23.020.35 - Gas cylinders
• Technical Committee: CEN/TC 286 - Liquefied petroleum gas equipment and accessories
• Drafting Committee: CEN/TC 286/WG 7 - Operational requirements - Transportable LPG cylinders and static LPG tanks
• Current Stage: 4599 - Dispatch of FV draft to CMC - Finalization for Vote
• Start Date: 21-Dec-2023
• Due Date: 18-Oct-2022
• Completion Date: 21-Dec-2023
• Directive: 2014/68/EU - Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Mandate: M/601 - COMMISSION IMPLEMENTING DECISION of 1.3.2024 on a standardisation request to the European Committee for Standardization and the European Committee for Electrotechnical Standardization as regards pressure equipment and assemblies in support of Directive 2014/68/EU of the European Parliament and of the Council
• Ref Project: oSIST prEN 14570:2022 - LPG equipment and accessories - Equipping of overground and underground LPG vessels

Relations

• Revises: EN 14570:2014 - LPG equipment and accessories - Equipping of overground and underground LPG vessels
• Effective Date: 13-Jan-2021

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2022
Oprema in pribor za utekočinjeni naftni plin (UNP) - Oprema za nadzemne in
podzemne posode za UNP
LPG equipment and accessories - Equipping of overground and underground LPG
vessels
Flüssiggas-Geräte und Ausrüstungsteile ¿ Ausrüstung von oberirdisch und unterirdisch
aufgestellten Behältern für Flüssiggas (LPG)
Équipements et accessoires GPL - Équipement des réservoirs sous pression GPL
aériens et enterrés
Ta slovenski standard je istoveten z: prEN 14570
ICS:
23.020.10 Nepremične posode in Stationary containers and
rezervoarji tanks
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
prEN 14570
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2022
ICS 23.020.35 Will supersede EN 14570:2014
English Version
LPG equipment and accessories - Equipping of overground
and underground LPG vessels
Équipements et accessoires GPL - Équipement des Flüssiggas-Geräte und Ausrüstungsteile ¿ Ausrüstung
réservoirs sous pression GPL aériens et enterrés von oberirdisch und unterirdisch aufgestellten
Behältern für Flüssiggas (LPG)
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 286.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 14570:2022 E
worldwide for CEN national Members.

prEN 14570:2022 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and abbreviations . 7
3.1 Terms and definitions . 7
3.2 Abbreviations . 9
4 Pressure vessel equipment . 9
4.1 General. 9
4.2 Selection of pressure vessel equipment . 10
4.3 Screwed joints . 10
4.4 Seals and gaskets . 10
5 Operational functions . 11
5.1 General. 11
5.2 Pressure relief . 12
5.2.1 General. 12
5.2.2 Isolating devices and manifolds . 12
5.2.3 Vent pipes . 12
5.3 Drainage . 13
5.4 Liquid removal system . 13
5.5 Maximum fill indication/control . 13
5.5.1 General. 13
5.5.2 Fixed liquid level gauge . 13
5.5.3 Overfill protection device . 14
5.6 Filling system. 14
5.7 Vapour off-take . 14
5.8 Vapour return . 14
5.9 Liquid off-take . 14
5.10 Liquid return . 14
5.11 Temperature indication . 14
5.12 Pressure indication . 14
5.13 Liquid level indication . 15
5.14 Road tanker potential bonding . 15
5.15 Earthing . 15
5.16 Cathodic protection . 15
6 Equipping . 15
6.1 General. 15
6.2 Screwed joints . 16
6.3 Flanged joints . 16
7 Checking and testing . 16
7.1 General. 16
7.2 Leak tightness . 16
7.3 Excess flow valve . 17

prEN 14570:2022 (E)
7.4 Completion and purging . 17
8 Storage, handling and transportation . 17
9 Documentation . 17
Annex A (informative) Examples of alternative means of over pressure protection for
underground/mounded pressure vessels . 18
Annex B (normative) Settings and discharge rates for PRVs and hydrostatic relief valves . 19
B.1 Setting . 19
B.2 Discharge rates . 19
B.2.1 General . 19
B.2.2 Above ground pressure vessels . 19
B.2.3 Underground/fully mounded pressure vessels . 20
B.2.4 Semi-mounded pressure vessels . 20
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2014/68/EU aimed to be covered . 21
Bibliography . 23

prEN 14570:2022 (E)
European foreword
This document (prEN 14570:2022) has been prepared by Technical Committee CEN/TC 286 “Liquefied
petroleum gas equipment and accessories”, the secretariat of which is held by NSAI.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 14570:2014.
In comparison with the previous edition, the following technical modifications have been made:
— Update to align with Directive 2014/68/EU;
— Update to 4.1, 4.2, 4.4;
— Introduction of 5.16 Cathodic protection; and
— Update to 7.2.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral part
of this document.
prEN 14570:2022 (E)
Introduction
This document calls for the use of substances and procedures that may be injurious to health and/or the
environment if adequate precautions are not taken. It refers only to technical suitability: it does not
absolve the user from their legal obligations at any stage.
It is recommended that manufacturers develop an environmental management policy. For guidance, see
the EN ISO 14000 series [1], [2] and [3].
Protection of the environment is a key political issue in Europe and elsewhere. For TC 286 this is covered
in CEN/TS 16765 [4] LPG equipment and accessories - Environmental considerations for CEN/TC 286
standards, and this Technical Specification should be read in conjunction with this standard. The
Technical Specification provides guidance on the environmental aspects to be considered regarding
equipment and accessories produced for the LPG industry and the following is addressed:
a) design;
b) manufacture;
c) packaging;
d) use and operation; and
e) disposal.
It has been assumed in the drafting of this document that the execution of its provisions is entrusted to
appropriately qualified and experienced people.
All pressures are gauge pressures unless otherwise stated.
prEN 14570:2022 (E)
1 Scope
This document specifies requirements for the equipping (fitting out) of LPG pressure vessels with fittings
and accessories.
It is applicable to overground and underground LPG pressure vessels, with a volume not greater than
13 m manufactured in accordance with EN 12542:2020 or equivalent and which have been hydraulically
tested.
The fittings and accessories covered by this document are directly mounted onto the pressure vessel
connections.
This document excludes the equipping of depot
...