EN 1176-10:2023
(Main)Playground equipment and surfacing - Part 10: Additional specific safety requirements and test methods for fully enclosed play equipment
Playground equipment and surfacing - Part 10: Additional specific safety requirements and test methods for fully enclosed play equipment
This document is applicable to fully enclosed play equipment intended for installation inside and outside buildings, for children up to 14 years old, see 3.1.
The purpose of this document is to provide additional safety requirements covering particulars of these structures.
Spielplatzgeräte und Spielplatzböden - Teil 10: Zusätzliche besondere sicherheitstechnische Anforderungen und Prüfverfahren für vollständig umschlossene Spielgeräte
Dieses Dokument ist anwendbar für vollständig umschlossene Spielgeräte, die für die Aufstellung innerhalb und außerhalb von Gebäuden und für Kinder bis 14 Jahren vorgesehen sind, siehe 3.1.
Der Zweck dieses Dokumentes besteht darin, zusätzliche sicherheitstechnische Anforderungen bereitzustellen, die Einzelheiten dieser Konstruktionen behandeln.
Équipements et sols d’aires de jeux - Partie 10 : Exigences de sécurité et méthodes d’essai complémentaires spécifiques aux équipements de jeux totalement fermés
Le présent document s’applique aux équipements de jeux totalement fermés installés tant à l’intérieur qu’à l’extérieur des bâtiments et destinés à des enfants jusqu’à 14 ans, voir 3.1.
Le présent document a pour objectif de fournir des exigences de sécurité complémentaires couvrant les spécificités de ces structures.
Oprema in podloge otroških igrišč - 10. del: Dodatne posebne varnostne zahteve in preskusne metode za zaključene igralne enote
Ta dokument se uporablja za zaključene igralne enote, namenjene za namestitev znotraj in zunaj stavb, za otroke do starosti 14 let, glej 3.1.
Namen tega dokumenta je zagotoviti dodatne varnostne zahteve, ki zajemajo podrobnosti teh konstrukcij.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2023
Nadomešča:
SIST EN 1176-10:2008
Oprema in podloge otroških igrišč - 10. del: Dodatne posebne varnostne zahteve
in preskusne metode za zaključene igralne enote
Playground equipment and surfacing - Part 10: Additional specific safety requirements
and test methods for fully enclosed play equipment
Spielplatzgeräte und Spielplatzböden - Teil 10: Zusätzliche besondere
sicherheitstechnische Anforderungen und Prüfverfahren für vollständig umschlossene
Spielgeräte
Équipements et sols d’aires de jeux - Partie 10 : Exigences de sécurité et méthodes
d’essai complémentaires spécifiques aux équipements de jeux totalement fermés
Ta slovenski standard je istoveten z: EN 1176-10:2023
ICS:
97.200.40 Igrišča Playgrounds
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 1176-10
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2023
EUROPÄISCHE NORM
ICS 97.200.40 Supersedes EN 1176-10:2008
English Version
Playground equipment and surfacing - Part 10: Additional
specific safety requirements and test methods for fully
enclosed play equipment
Équipements et sols d'aires de jeux - Partie 10 : Spielplatzgeräte und Spielplatzböden - Teil 10:
Exigences de sécurité et méthodes d'essai Zusätzliche besondere sicherheitstechnische
complémentaires spécifiques aux équipements de jeux Anforderungen und Prüfverfahren für vollständig
totalement fermés umschlossene Spielgeräte
This European Standard was approved by CEN on 23 July 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1176-10:2023 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Safety requirements . 7
4.1 General. 7
4.2 Emergency procedures and fire safety management . 7
4.2.1 Flammability of materials. 7
4.2.2 Evacuation . 7
4.3 Design and manufacture . 10
4.3.1 General. 10
4.3.2 Impact protection . 10
4.3.3 Visibility . 10
4.3.4 Determination of spaces and areas . 11
4.3.5 Connections and platforms . 11
4.3.6 Rope features . 11
4.3.7 Foam play features . 12
4.3.8 Lighting . 12
4.3.9 Signage . 12
4.4 Specific equipment . 12
4.4.1 Slides . 12
4.4.2 Drop slides. 12
4.4.3 Overhead track rides (rigid) . 13
4.4.4 Spinning poles . 15
4.4.5 Ball pool . 16
4.4.6 Cannons . 17
4.4.7 Bouncing elements in indoor play structures . 17
4.4.8 Electrically powered equipment . 18
5 Inspection and maintenance information to be provided by the manufacturer or
supplier . 18
6 Test reports . 19
7 Marking . 19
European foreword
This document (EN 1176-10:2023) has been prepared by Technical Committee CEN/TC 136 “Sports,
playground and other recreational facilities and equipment”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2024, and conflicting national standards shall be
withdrawn at the latest by March 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1176-10:2008.
a) 1 Scope. Minor amendment made to simplify and to align with the current approach within
standards.
b) Terms and definitions updated:
1. 3.11 adult access route. New additional definition introduced
2. 3.12 bouncing element in indoor play structures. New additional definition;
3. 3.13 spinning pole. New additional definition introduced.
c) 4.2.1 Materials including flammability. The term “where practical” is introduced as it is not possible
to test some minor components;
d) 4.2.2.1 Adult access route. Re-named from evacuation routes to be more logical. Amendments made
and agreed in line with knowledge and experience gained since EN 1176-10 was issued in 2008;
e) 4.2.2.3 Table 1 revised to align with the amendments in 4.2.2 and for clarity of its content;
f) 4.2.2.4 Capacity. The formula has been revised as agreed to result in realistic operating levels;
g) 4.3 Design and manufacture. Some provisions under this general heading included in
EN 1176-10:2008 have been excluded where they can be referenced in Part 1, thus aligning with
current practice. Additional provisions and changes have though been noted;
h) 4.3.2.1 Climbability. Some minor additions/improvements made to the wording.
i) 4.3.4.2 Falling space and impact areas. This revision incorporates additional information to improve
understanding of the requirements in this document;
j) 4.3.4.3 Proximity to hard or projecting surfaces. An additional important provision, which was
omitted in EN 1176-10:2008;
k) 4.3.5 Connections and platforms. The revised wording agreed is more relevant and informative.
l) 4.3.6 Rope features. Reference to preventing limbs passing through the standing surface now
included;
m) 4.3.7 Foam play features. Additional provision agreed. It was not previously included
n) 4.4.1 Slides. Length provision amended as agreed in reference to EN 1176-3;
o) 4.4.2.7 Run-out section. The formula has been made clearer;
p) 4.4.3.3 The traveller. Additional wording incorporated improving this provision;
q) 4.4.3.7 and Figure 4. Figure 4 now covers both round section and flat seats with specific minimum
underside ground clearances. Some minor adjustments have been made to the measurements shown
in the 2008 version of Part 10 to align with current practice;
r) 4.4.4 Spinning poles. A completely new section;
s) 4.4.5.2 The floor surface provision for ball pools has been amended to be more appropriate;
t) 4.4.5.6 The minimum diameter of the balls is now specified at 60 mm aligning with current
knowledge and experience;
u) 4.4.6 Cannons. A new provision whereby a minimum ball size is specified;
v) 4.4.7 Bouncing elements in indoor play structures. A new section;
w) 5.4 Instructions for maintenance have been amended to reflect currently accepted good practice;
x) 5.5 included specifically to define separately “safety measures and procedures shall be installed” and
what they incorporate.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
1 Scope
This document is applicable to fully enclosed play equipment intended for installation inside and outside
buildings, for children up to 14 years old, see 3.1.
The purpose of this document is to provide additional safety requirements covering particulars of these
structures.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1021-1, Furniture - Assessment of the ignitability of upholstered furniture - Part 1: Ignition source
smouldering cigarette
EN 1021-2, Furniture - Assessment of the ignitability of upholstered furniture - Part 2: Ignition source match
flame equivalent
EN 1176-1:2017, Playground equipment and surfacing - Part 1: General safety requirements and test
methods
EN 1176-3:2017, Playground equipment and surfacing - Part 3: Additional specific safety requirements and
test methods for slides
EN 1176 (all parts), Playground equipment and surfacing
EN 1177, Impact attenuating playground surfacing — Methods of test for determination of impact
attenuation
EN ISO 11925-2, Reaction to fire tests - Ignitability of products subjected to direct impingement of flame -
Part 2: Single-flame source test (ISO 11925-2)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 1176-1, EN 1176-3, EN 1177
and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
3.1
fully enclosed play equipment
equipment and structure, including components and constructional elements with, or on which, children
can play, that are within a three-dimensional enclosure with specified entrances and exits
3.2
drop s
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.