EN ISO 16812:2007
(Main)Petroleum, petrochemical and natural gas industries - Shell-and-tube heat exchangers (ISO 16812:2007)
Petroleum, petrochemical and natural gas industries - Shell-and-tube heat exchangers (ISO 16812:2007)
ISO 16812:2007 specifies requirements and gives recommendations for the mechanical design, material selection, fabrication, inspection, testing and preparation for shipment of shell-and-tube heat exchangers for the petroleum, petrochemical and natural gas industries.
ISO 16812:2007 is applicable to the following types of shell-and-tube heat exchangers: heaters, condensers, coolers and reboilers.
ISO 16812:2007 is not applicable to vacuum-operated steam surface condensers and feed-water heaters.
Erdöl-, petrochemische und Erdgasindustrie - Rohrbüdelwärmetauscher (ISO 16812:2007)
Industries du pétrole, de la pétrochimie et du gaz naturel - Échangeurs de chaleur à faisceaux (ISO 16812:2007)
L'ISO 16812:2007 spécifie les exigences et fournit des recommandations relatives à la conception mécanique, à la sélection des matériaux, à la fabrication, au contrôle, aux essais et à la préparation pour l'expédition des échangeurs de chaleur à faisceaux tubulaires pour les industries du pétrole, de la pétrochimie et du gaz naturel.
L'ISO 16812:2007 s'applique aux types d'échangeurs de chaleur à faisceaux tubulaires suivants: les réchauffeurs, les condenseurs, les refroidisseurs et les rebouilleurs.
L'ISO 16812:2007 ne s'applique pas aux condenseurs de vapeur d'eau et aux réchauffeurs d'eau d'alimentation de chaudière.
Petrokemična industrija ter industrija za predelavo nafte in zemeljskega plina - Toplotni izmenjevalniki za ohišja in cevi (ISO 16812:2007)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2007
1DGRPHãþD
SIST EN ISO 16812:2004
3HWURNHPLþQDLQGXVWULMDWHULQGXVWULMD]DSUHGHODYRQDIWHLQ]HPHOMVNHJDSOLQD
7RSORWQLL]PHQMHYDOQLNL]DRKLãMDLQFHYL ,62
Petroleum, petrochemical and natural gas industries - Shell-and-tube heat exchangers
(ISO 16812:2007)
Erdöl-, petrochemische und Erdgasindustrie - Rohrbüdelwärmetauscher (ISO
16812:2007)
Industries du pétrole, de la pétrochimie et du gaz naturel - Échangeurs de chaleur a
faisceaux (ISO 16812:2007)
Ta slovenski standard je istoveten z: EN ISO 16812:2007
ICS:
71.120.30 Prenosniki toplote Heat exchangers
75.180.20 Predelovalna oprema Processing equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 16812
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2007
ICS 75.180.20; 27.060.30 Supersedes EN ISO 16812:2003
English Version
Petroleum, petrochemical and natural gas industries - Shell-and-
tube heat exchangers (ISO 16812:2007)
Industries du pétrole, de la pétrochimie et du gaz naturel - Erdöl-, petrochemische und Erdgasindustrie -
Échangeurs de chaleur à faisceaux (ISO 16812:2007) Rohrbüdelwärmetauscher (ISO 16812:2007)
This European Standard was approved by CEN on 3 February 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16812:2007: E
worldwide for CEN national Members.
Foreword
This document (EN ISO 16812:2007) has been prepared by Technical Committee ISO/TC 67
"Materials, equipment and offshore structures for petroleum and natural gas industries" in
collaboration with Technical Committee CEN/TC 12 "Materials, equipment and offshore
structures for petroleum, petrochemical and natural gas industries", the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by August 2007, and conflicting national
standards shall be withdrawn at the latest by August 2007.
This document supersedes EN ISO 16812:2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.
Endorsement notice
The text of ISO 16812:2007 has been approved by CEN as EN ISO 16812:2007 without any
modifications.
INTERNATIONAL ISO
STANDARD 16812
Second edition
2007-02-15
Petroleum, petrochemical and natural gas
industries — Shell-and-tube heat
exchangers
Industries du pétrole, de la pétrochimie et du gaz naturel — Échangeurs
de chaleur à faisceaux
Reference number
ISO 16812:2007(E)
©
ISO 2007
ISO 16812:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
ISO 16812:2007(E)
Contents Page
Foreword. v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 2
4 General. 3
5 Proposals. 3
6 Drawings and other required data . 4
6.1 Outline drawings and other supporting data. 4
6.2 Information required after outline drawings are reviewed . 5
6.3 Reports and records. 6
7 Design . 7
7.1 Design temperature . 7
7.2 Cladding for corrosion allowance. 7
7.3 Shell supports . 7
7.4 Stationary head . 8
7.5 Floating head. 8
7.6 Tube bundle. 9
7.7 Nozzles and other connections. 12
7.8 Flanged external girth joints. 13
7.9 Expansion joints . 13
7.10 Gaskets . 14
7.11 Handling devices . 15
7.12 Hydrogen service. 15
8 Materials . 15
8.1 General. 15
8.2 Gaskets . 16
8.3 Tubes. 16
9 Fabrication. 16
9.1 Shells . 16
9.2 Pass-partition plates. 16
9.3 Connection junctions . 16
9.4 Tubes. 17
9.5 Welding . 17
9.6 Heat treatment. 17
9.7 Dimensional tolerances . 18
9.8 Gasket contact surfaces other than nozzle-flange facings. 18
9.9 Tube holes . 19
9.10 Tube-to-tubesheet joints. 19
9.11 Assembly . 19
10 Inspection and testing. 20
10.1 Quality assurance. 20
10.2 Quality control. 20
10.3 Pressure testing. 21
10.4 Nameplates and stampings . 22
ISO 16812:2007(E)
11 Preparation for shipment . 22
11.1 Protection. 22
11.2 Identification. 23
12 Supplemental requirements. 23
12.1 General . 23
12.2 Design . 23
12.3 Examination. 23
Annex A (informative) Recommended practices. 25
Annex B (informative) Shell-and-tube heat exchanger checklist . 27
Annex C (informative) Shell-and-tube heat exchanger data sheets . 28
Annex D (informative) Responsibility data sheet . 39
Bibliograp
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.