prEN 10369-2
(Main)Prestressing steels - Protected and sheathed strands for prestressing - Part 2: Sliding strands
Prestressing steels - Protected and sheathed strands for prestressing - Part 2: Sliding strands
This document specifies the specific requirements for sliding protected and sheathed strands (type S).
The general requirements for protected and sheathed high strength steel strands are given in prEN 10369-1.
Spannstähle - Geschützte und gehüllte Litzen für Vorspannen - Teil 2: Schiebbare Litzen
Dieses Dokument legt spezifische Anforderungen an geschützte und gehüllte schiebbare Litzen (Typ S) fest.
Allgemeine Anforderungen an geschützte und gehüllte schiebbare Litzen sind in prEN 10369-1 enthalten.
Aciers de précontrainte - Torons de précontrainte protégés et gainés - Partie 2 : Torons coulissants
Le présent document spécifie les exigences applicables aux torons protégés gainés coulissants (type S).
Les exigences générales relatives aux torons en acier à haute résistance protégés gainés sont fournies par le prEN 10369-1.
Prednapeta jekla - Zaščitena in obložena vlakna za prednapenjanje - 2. del: Drsne žice
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2019
Prednapeta jekla - Zaščitena in obložena vlakna za prednapenjanje - 2. del: Drsne
žice
Prestressing steels - Protected and sheathed strands for prestressing - Part 2: Sliding
strands
Spannstähle - Geschützte und gehüllte Litzen für Vorspannen - Teil 2: Schiebbare Litzen
Aciers de précontrainte - Torons de précontrainte protégés et gainés - Partie 2 : Torons
coulissants
Ta slovenski standard je istoveten z: prEN 10369-2
ICS:
77.080.20 Jekla Steels
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2019
ICS 77.140.15
English Version
Prestressing steels - Protected and sheathed strands for
prestressing - Part 2: Sliding strands
Aciers de précontrainte - Torons de précontrainte Spannstähle - Geschützte und gehüllte Litzen für
protégés et gainés - Partie 2 : Torons coulissants Vorspannen - Teil 2: Schiebbare Litzen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 459/SC 4.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10369-2:2019 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Classification and designation . 4
4.1 Classification . 4
4.2 Designation. 4
5 Manufacturing process . 5
6 Requirements for materials used for sliding protected and sheathed strands. 5
7 Requirements for sliding protected and sheathed strands . 5
7.1 Overall diameter. 5
7.2 Straightness . 5
7.3 Mass of the protection product . 5
7.4 Sheath . 5
European foreword
This document (prEN 10369-2:2019) has been prepared by Technical Committee CEN/TC 459/SC 4
“Concrete reinforcing and prestressing steels”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
prEN 10369 consists of three parts under the general title “Prestressing steels — Protected and
sheathed strands for prestressing”:
— Part 1: General requirements
— Part 2: Sliding strands
— Part 3: Adherent strands
1 Scope
This document specifies the specific requirements for sliding protected and sheathed strands (type S).
The general requirements for protected and sheathed high strength steel strands are given in
prEN 10369-1.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. F
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.