ECISS/TC 104 - Concrete reinforcing and prestressing steels

This document specifies requirements for hot dip galvanized reinforcing steel in the form of products which meet the requirements of EN 10080 and subjected, where appropriate, to further processing, e.g. bars, bent bars, stirrups, products straightened from coils, products cut from bars, welded structures and any other components fabricated for use in the reinforcement of concrete.
This document does not apply to hot dip galvanized reinforcement for prestressing or components of these reinforcements.

This document specifies chemical and mechanical test methods and measurement methods of geometrical characteristics applicable to reinforcing bars, rods and wire for concrete.
This document does not cover the sampling conditions that are dealt with in the product standards.
A list of options for agreement between the parties involved is provided in Annex A.

This document specifies chemical and mechanical test methods and measurement methods of geometrical characteristics applicable to welded fabric and lattice girders for the reinforcement of concrete.
NOTE       In some countries, the expression "welded wire reinforcement" is used in place of "welded (wire) fabric".
For those tests not specified in this document (e.g. bend test, rib/indentation geometry, mass per metre), ISO 15630-1 is applicable.
This document does not cover the sampling conditions that are dealt with in the product standards.
A list of options for agreement between the parties involved is provided in Annex A.

This document specifies test methods applicable to prestressing steel (bar, wire or strand) for concrete.
This document does not cover the sampling conditions that are dealt with in the product standards.
A list of options for agreement between the parties involved is provided in Annex A.

This document specifies general requirements and definitions for the performance characteristics of weldable reinforcing steel used for the reinforcement of concrete structures, delivered as finished products in the form of:
-   bars, coils (rod, wire) and de-coiled products;
-   sheets of factory-made machine-welded fabric;
-   lattice girders.
1.2   Steels according to this document have a ribbed, indented or smooth surface.
1.3   This document does not apply to:
-   non-weldable reinforcing steel;
-   galvanized reinforcing steel;
-   epoxy-coated reinforcing steel;
-   corrosion resistant reinforcing steel;
-   prestressing steels (see prEN 10138-1 to -4);
-   indented strip;
-   further processing, e.g. cutting or cutting and bending.

This document specifies test methods applicable to prestressing steel (bar, wire or strand) for concrete.
This document does not cover the sampling conditions that are dealt with in the product standards.

This document specifies the requirements for uncoated high strength steel strands or zinc or zinc alloy coated high strength steel strands, encapsulated with wax and a sheath for construction applications.
The document applies only to products as supplied by the manufacturer.

1.1   This document specifies general requirements and definitions for the essential characteristics of weldable reinforcing steel used for the reinforcement of concrete structures, delivered as finished products in the form of:
-   bars (including those produced by the reinforcing steel manufacturer from coil);
-   coils;
-   sheets of factory-made machine-welded fabric;
-   lattice girders.
1.2   Steels according to this document have a ribbed, indented or smooth surface.
NOTE 1   The protrusions between indentations of indented reinforcing steel have the same function as transverse ribs of ribbed reinforcing steel. There is no definition which specifies the difference between ribbed and indented surface geometry. Therefore, in this document, the same bond parameters are used for ribbed and indented steel.
1.3   This document does not apply to:
-   non-weldable reinforcing steel;
-   galvanized reinforcing steel;
-   epoxy-coated reinforcing steel;
-   corrosion resistant reinforcing steel;
-   prestressing steels;
-   indented strip;
-   further processing by a processor, e.g. de-coiling/straightening, cutting or cutting and bending.
NOTE 2   Further processing could influence some essential characteristics of the product.

This document specifies the requirements and definitions for the essential characteristics of prestressing bars, which are used for the prestressing of concrete and which are delivered as finished products in the form of:
-   hot rolled and processed bars;
-   plain and threaded bars.
NOTE 1   The specification of manufacturing processes related to the finished product is required to ensure that the essential characteristics can be tested properly and that test results are valid. It is not possible to anticipate that any other manufacturing process leads to products which can be tested properly with the specified test methods. Thus, a conclusion to the safe application in building construction would not any longer be possible for those products.
This document does not apply to:
-   galvanized steel;
-   epoxy coated steel;
-   reinforcing steel (see EN 10080);
-   further processing.
NOTE 2   Example for further processing: Plain bars are also applied in systems for the prestressing of concrete with threaded ends. The threaded ends depend in length and type on the intended use of the system and are manufactured downstream in the supply chain.

This document specifies product characteristic test/assessment method and the way of expressing test results for stainless steel as defined in EN 10088-1:2014 and designated as in EN 10088-1:2014 for the use of the reinforcement of concrete.
It applies to stainless steel products with ribbed or indented surfaces, which are in the form of:
-   bars and coils (rod, wire);
-   sheets of factory-made machine-welded fabric;
-   lattice girders and hybrid lattice girders composed by stainless steel and by weldable reinforcing steel according to prEN 10080:2023.
Steels according to this document have a ribbed, indented or smooth surface.
NOTE   The protrusions between indentations of indented reinforcing steel have the same function as transverse ribs of ribbed reinforcing steel. There is no definition, which specifies the difference between ribbed and indented surface geometry. Therefore, in this document, the same bond parameters are used for ribbed and indented steel.
This document does not apply to:
-   pre-stressed stainless steels;
-   indented strip;
-   stainless steel tube filled with carbon steel swarf, which is then hot or cold reduced;
-   stainless steel smooth bar with weld material deposited on it;
-   galvanized reinforcing steel;
-   epoxy-coated reinforcing steel.

This document specifies the requirements for uncoated high strength steel strands or zinc or zinc alloy coated high strength steel strands, encapsulated with a protection product and a sheath 1).
The intended use of these products is mainly the prestressing of concrete.
NOTE   These products can also be used in other stress applications in the construction field (e.g. stay cables for bridges) where the protection of the products is not removed in use.
The standard applies only to products as supplied by the producer.
1) The word "sheath" used in the present document does not cover the sheaths as stated in mandate M/115 and specified in EN 523.

This document specifies the specific requirements for sliding protected and sheathed strands (type S).
The general requirements for protected and sheathed high strength steel strands are given in prEN 10369-1.

This document specifies the specific requirements for adherent protected and sheathed strands (type A).
The general requirements for protected and sheathed high strength steel strands are given in prEN 10369-1.

This document specifies product characteristic, test/assessment method and the way of expressing test results, for stainless steel as defined in EN 10088-1 and designated as in EN 10088-1 for the use of the reinforcement of concrete.
It applies to stainless steel products with ribbed or indented surfaces, which are in the form of:
-   bars and coils (rod, wire);
-   sheets of factory-made machine-welded fabric;
-   lattice girders and hybrid lattice girders composed by stainless steel and by weldable reinforcing steel according to EN 10080.
This document does not apply to:
-   pre-stressed stainless steels;
-   indented strip;
-   stainless steel tube filled with carbon steel swarf, which is then hot or cold reduced;
-   stainless steel smooth bar with weld material deposited on it;
-   galvanized reinforcing steel;
-   epoxy-coated reinforcing steel.

This European Standard specifies requirements for galvanized (hot-dip zinc coated) reinforcing steel in the form of bars, coils (rod, wire), welded fabric and lattice girder for the reinforcement of concrete.
It specifies seven classes of coating, class A to class G, corresponding to different coating masses (see 9.5.4).
This specification may also be understood to cover other classes of coating whose details are not stated in this edition of the standard but whose specified values of properties are defined consistenly with Clause 9 and the conformity of which is carried out according to Clause 10.
This European Standard does not apply to galvanized (hot-dip zinc coated) reinforcement for prestressing or components of these reinforcements.

This document specifies requirements for hot-dip galvanized reinforcing steel in the form of products according to EN 10080 and subjected to further processing, e.g. bent bars, stirrups, products straightened from coils, products cut from bars, welded structures (other than welded fabric or lattice girders according to EN 10348, Part 1) and any other components fabricated for use in the reinforcement of concrete.
This document does not apply to hot dip galvanized reinforcement for pre-stressing or components of these reinforcements.

ISO 15630-2:2010 specifies test methods applicable to welded fabric for the reinforcement of concrete.

ISO 15630-1:2010 specifies test methods applicable to reinforcing bars, wire rod and wire for concrete.

ISO 15630-3:2010 specifies test methods applicable to prestressing steels (bar, wire or strand) for concrete.

This European Prestandard specifies requirements for the chemical composition and the mechanical and geometrical properties of weldable ribbed reinforcing steel in grade B500, categories A and B (designated as steels B500A and B500B, see table 1) used for the reinforcement of concrete structures in the form of - bars and coils or as elements for the manufacturing of welded fabric, - sheets of factory made machine welded fabric in the diameter ranges given in table 1.