iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14620-3:2006

(Main)

Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 3: Concrete components

Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 3: Concrete components

This European Standard specifies general requirements for materials, design and construction of the concrete components of the refrigerated liquefied gas storage tanks.
This European Standard deals with the design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and –165 °C.

Auslegung und Herstellung standortgefertigter, stehender, zylindrischer Flachboden-Stahltanks für die Lagerung von tiefkalt verflüssigten Gasen bei Betriebstemperaturen zwischen 0 °C und -165 °C - Teil 3: Bauteile aus Beton

Dieser Teil von EN 14620 legt allgemeine Anforderungen an Werkstoffe, Auslegung und Ausführung von Betonbauteilen für Tanks zur Lagerung von tiefkalt verflüssigten Gasen fest.

Conception et fabrication de réservoirs en acier à fond plat, verticaux, cylindriques, construits sur site, destinés au stockage des gaz réfrigérés, liquéfiés, dont les températures de service sont comprises entre 0 °C et -165 °C - Partie 3: Constituants béton

La présente Norme européenne spécifie les exigences générales relatives aux matériaux, à la conception et à la construction des constituants de l'enceinte extérieure béton des réservoirs de stockage des gaz réfrigérés liquéfiés.
La présente Norme Européenne présente la conception et fabrication de réservoirs en acier à fond plat, verticaux, cylindriques, construits sur site, destinés au stockage des gaz réfrigérés, liquéfiés, dont les températures de service sont comprises entre 0 °C et – 165 °C.

Načrtovanje in proizvodnja na mestu postavitve grajenih navpičnih, valjastih jeklenih posod z ravnim dnom za shranjevanje hlajenih utekočinjenih plinov z delovnimi temperaturami med 0 °C in –165 °C - 3. del: Betonski deli

General Information

Status
Published
Publication Date
12-Sep-2006
ICS
23.020.10 - Stationary containers and tanks
Technical Committee
CEN/TC 265 - Site built metallic tanks for the storage of liquids
Drafting Committee
CEN/TC 265/WG 10 - Revision of EN 14620
Current Stage
9092 - Decision on results of review/2YR ENQ - revise - Review Enquiry
Completion Date
17-Jun-2021
Ref Project
SIST EN 14620-3:2007 - Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 3: Concrete components

Buy Standard

EN 14620-3:2007EN 14620-3:2007
PreviousNext
Standard
EN 14620-3:2007
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C
- Part 3: Concrete componentsOLConception et fabrication de réservoirs en acier a fond plat, verticaux, cylindriques, construits sur site, destinés au stockage des gaz réfrigérés, liquéfiés, dont les températures de service sont comprises entre 0 °C et -165 °C - Partie 3: Constituants bétonAuslegung und Herstellung standortgefertigter, stehender, zylindrischer Flachboden-Stahltanks für die Lagerung von tiefkalt verflüssigten Gasen bei Betriebstemperaturen zwischen 0 °C und -165 °C - Teil 3: Bauteile aus BetonTa slovenski standard je istoveten z:EN 14620-3:2006SIST EN 14620-3:2007en23.020.10UH]HUYRDUMLStationary containers and tanksICS:SLOVENSKI
STANDARDSIST EN 14620-3:200701-januar-2007







EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14620-3
September 2006 ICS 23.020.10 English Version
Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 3: Concrete components
Conception et fabrication de réservoirs en acier à fond plat, verticaux, cylindriques, construits sur site, destinés au stockage des gaz réfrigérés, liquéfiés, dont les températures de service sont comprises entre 0 °C et -165 °C - Partie 3: Constituants béton
Auslegung und Herstellung standortgefertigter, stehender, zylindrischer Flachboden-Stahltanks für die Lagerung von tiefkalt verflüssigten Gasen bei Betriebstemperaturen zwischen 0 °C und -165 °C - Teil 3: Bauteile aus Beton This European Standard was approved by CEN on 20 February 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2006 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14620-3:2006: E



EN 14620-3:2006 (E) 2 Contents Page Foreword.4 1 Scope.5 2 Normative references.5 3 Terms and definitions.5 4 General.5 5 Vapour tightness.6 6 Materials.6 6.1 General.6 6.2 Concrete.6 6.3 Pre-stressing and reinforcing steel.6 7 Design.7 7.1 General.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12285-3:2019(Main)
Workshop fabricated steel tanks - Part 3: Horizontal cylindrical single skin and double skin tanks for the underground storage of flammable and nonflammable water polluting liquids for heating and cooling of buildings
SIST EN 12285-3:2019

This document specifies the product characteristics and test/assessment methods for workshop fabricated cylindrical, horizontal steel tanks, single (type S) and double skin (type D) intended to be used for the underground storage of water polluting liquids (both flammable and non-flammable), specifically used for storage and/or supply of fuel for building heating/cooling systems, and of hot or cold water not intended for human consumption at normal ambient temperature conditions (−20 °C to +50 °C) within the following limits:
-   from 800 mm up to 3000 mm nominal diameter and;
-   up to a maximum overall length of 6 times the nominal diameter;
-   for liquids with a maximum density of up to 1,1 kg/l and;
-   with an operating pressure (Po) of maximum 50 kPa (0,5 bar(g)) and minimum – 5 kPa (–50 mbar(g)) and;
-   for double skin tanks with a vacuum leak detection system where the kinematic viscosity does not exceed 5 × 10−3 m2/s.
Two tank types are distinguished:
-   Type S: Single skin;
-   Type D: Double skin.
Tanks designed to this document allow for an earth cover of up to 1,5 m. If there are imposed traffic loads or a greater earth cover, calculation is required.
This document is not applicable to tanks installed in industrial processes or in petrol stations, nor to loads and special measures necessary in areas subject to risk of earthquakes and/or to flooding.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12285-1:2018(Main)
Workshop fabricated steel tanks - Part 1: Horizontal cylindrical single skin and double skin tanks for the underground storage of flammable and nonflammable water polluting liquids other than for heating and cooling of buildings
SIST EN 12285-1:2018

This document specifies the product characteristics and test methods for workshop fabricated cylindrical, horizontal steel tanks, single (type S) and double skin (type D) intended to be used for the underground storage of water polluting liquids (both flammable and non-flammable) and installed in industrial processes or in petrol stations at normal ambient temperature conditions (−20 °C to +50 °C) within the following limits:
-   from 800 mm up to 3 000 mm nominal diameter and;
-   up to a maximum overall length of 6 times the nominal diameter;
-   with an operating pressure (Po) of maximum 50 kPa (0,5 bar(g)) and minimum – 5 kPa (–50 mbar(g)) and;
-   for double skin tanks with a vacuum leak detection system where the kinematic viscosity does not exceed 5 × 10−3 m2/s.
Tanks designed to this standard allow for an earth cover of up to 1,5 m. If there are imposed traffic loads or a greater earth cover, calculation is expected to be carried out.
This document is not applicable to tanks used for storage and/or supply of fuel/gas for building heating/cooling systems, and of hot or cold water not intended for human consumption, nor to loads and special measures necessary in areas subject to risk of earthquakes.
Guidance on installation of tanks is presented in Annex A, which does not include special measures that might be necessary in areas subject to flooding.
This document is not applicable for the storage of liquids having dangerous goods classes listed in Table 1 because of the special dangers involved.
(...)
NOTE   The classifications referred to are those adopted by the United Nations Committee of Experts on the Transport of Dangerous Goods (not to be interpreted as tank classes described in 6.2).

  • Standard
    119 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14620-4:2006(Main)
Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 4: Insulation components
SIST EN 14620-4:2007

This European Standard specifies the requirements for materials, design and installation of the insulation of refrigerated liquefied gas (RLG) storage tanks.
RLG storage tanks store liquefied gas with a low boiling point, i.e. below normal ambient temperature.
The concept of storing such products in liquid form and in non-pressurized tanks therefore depends on the combination of latent heat of vaporization and thermal insulation.
Consequently thermal insulation for RLG storage tanks is not an ancillary part of the containment system (as for most ambient atmospheric hydrocarbon tanks) but it is an essential component and the storage tank cannot operate without a properly designed, installed and maintained insulation system.
The main functions of the insulation in RLG storage tanks are:
¾   to maintain the boil off below the specific limits;
¾   to protect the non low temperature parts/materials of the tank (mainly the outer tank) by maintaining these parts at their required ambient temperature;
¾   to limit the cool-down of the foundations/soil underneath the tank to prevent damage by frost heave;
¾   to prevent/minimize condensation and icing on the outer surfaces of the tank.
A wide range of insulation materials is available. However the material properties differ greatly amongst the various generically different materials and also within the same generic group of materials.
Therefore within the scope of this European Standard, only general guidance on selection of materials is given.
NOTE   For general guidance on selection of materials see Annex A.
This European Standard deals with the design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and –165 °C.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14620-5:2006(Main)
Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 5: Testing, drying, purging and cool-down
SIST EN 14620-5:2007

This European Standard specifies the requirements for testing, drying, purging and cool-down of the refrigerated liquefied gas storage tanks.
This European Standards deals with the design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and –165 °C.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14620-2:2006(Main)
Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 2: Metallic components
SIST EN 14620-2:2007

This European Standard specifies general requirements for the materials, design, construction and installation of the metallic components of refrigerated liquefied gas storage tanks.
This European Standard deals with the design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and –165 °C.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14620-1:2006(Main)
Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 1: General
SIST EN 14620-1:2007

This European Standard is a specification for vertical, cylindrical tanks, built on site, above ground and of which the primary liquid container is made of steel. The secondary container, if applicable, may be of steel or of concrete or a combination of both. An inner tank made only of pre-stressed concrete is excluded from the scope of this European Standard.
This European Standard specifies principles and application rules for the structural design of the “containment” during construction, testing, commissioning, operation (accidental included), and decommissioning. It does not address the requirements for ancillary equipment such as pumps, pumpwells, valves, piping, instrumentation, staircases etc. unless they can affect the structural design of the tank.
This European Standard applies to storage tanks designed to store products, having an atmospheric boiling point below ambient temperature, in a dual phase, i.e. liquid and vapour. The equilibrium between liquid and vapour phases being maintained by cooling down the product to a temperature equal to, or just below, its atmospheric boiling point in combination with a slight overpressure in the storage tank.
The maximum design pressure of the tanks covered by this European Standard is limited to 500 mbar. For higher pressures, reference can be made to EN 13445, Parts 1 to 5.
The operating range of the gasses to be stored is between 0 °C and –165 °C. The tanks for the storage of liquefied oxygen, nitrogen and argon are excluded.
The tanks are used to store large volumes of hydrocarbon products and ammonia with low temperature boiling points, generally called “Refrigerated Liquefied Gases” (RLG’s). Typical products stored in the tanks are: methane, ethane, propane, butane, ethylene, propylene, butadiene (this range includes the LNG’s and LPG’s).
NOTE   Properties of the gases are given in Annex A.
The requirements of this European Standard cannot cover all details of design and construction because of the variet

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12285-2:2005(Main)
Workshop fabricated steel tanks - Part 2: Horizontal cylindrical single skin and double skin tanks for the aboveground storage of flammable and non-flammable water polluting liquids
SIST EN 12285-2:2005

This document specifies the requirements for metallic shop fabricated cylindrical, horizontal steel tanks, single and double skin for the aboveground storage of water polluting liquids (both flammable and non-flammable) within the following limits:
-   from 800 mm up to 3 000 mm nominal diameter and,
-   up to a maximum overall length of 6 times the nominal diameter and,
-   for liquids with a maximum density of up to 1,9 kg/l and,
-   with an operating pressure (Po) of maximum 1,5 bar (abs.) and,
-   where double skin tanks with a vacuum leak detection system are used the cinematic viscosity of the stored media shall not exceed 5 ´ 10-3 m2/s.
This document is applicable for normal ambient temperature conditions (- 20 °C to + 50 °C). Where temperatures are outside this range, additional requirements need to be taken into account.
This document is not applicable for the storage of liquids having dangerous good classes listed in Table 1 because of the special dangers involved.
Table 1 - List of dangerous goods the storage of which are not covered by this document
UN-classification   Storage media
Class 1                     Explosives
Class 4.2                  Substances liable to spontaneous combustion
Class 4.3                  Substances which in contact with water emit flammable gases
Class 5.2                  Organic peroxides
Class 6.2                  Infectious substances
Class 7                   Radioactive material, hydrocyanic or hydrocyanic solvent liquids, metalcarbonyls, hydrofluoracid, bromide liquids
NOTE   The classifications referred to are those adopted by the United Nations Committee of Experts on the Transport of Dangerous Goods (not to be interpreted as tank classes described in 3.1.4).
This document does not cover the installation of tanks which might be subject to local regulations involving pollution control.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14015:2004(Main)
Specification for the design and manufacture of site built, vertical, cylindrical, flat-bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperature and above
SIST EN 14015:2005

This document specifies the requirements for the materials, design, fabrication, erection, testing and inspection of site built, vertical, cylindrical, flat bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperatures and above, and the technical agreements that need to be reached (see Annex A).
This document does not apply to tanks where the product is refrigerated to maintain it as a liquid at atmospheric pressure (see prEN 14620).
This document is concerned with the structural integrity of the basic tank structure and does not provide requirements for considering process design, operational issues, safety and firefighting facilities, in-service inspection, maintenance or repair. These aspects are covered in detail in other Codes of Practice (see Annex B).
1.2   This document applies to closed-top tanks, with and without internal floating covers (see Annex C) and open-top tanks, with and without floating roofs (see Annexes D and E). It does not apply to 'lift-type' gas holders.
1.3   This document applies to storage tanks with the following characteristics:
a)   design pressure less than 500 mbar ) and design internal negative pressure not lower than 20 mbar (see 5.1 for pressure limitations);
b)   design metal temperature not lower than -40 °C and not higher than +300 °C (see 5.2.2);
c)   maximum design liquid level not higher than the top of the cylindrical shell.
1.4   The limits of application of this document terminate at the following locations.
- face of the first flange in a bolted flange connection;
- first threaded joint on the pipe or coupling outside of the tank shell, roof or bottom;
- first circumferential joint in a pipe not having a flange connection.
1.5 This document is applicable to steel tanks with a maximum design strength £ 260 N/mm2.
1.6   In addition to the definitive requirements, this document also requires the items detailed in Annex A to be documented. For compliance with this document,

  • Standard
    247 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 14620-5(Main)
Design and manufacture of site built, vertical, cylindrical, flat-bottomed tank systems for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -196 °C - Part 5: Testing, drying, purging and cool-down
oSIST prEN 14620-5:2023

This document specifies the requirements for testing, drying, purging, cool-down and decommissioning of refrigerated liquefied gas storage tanks.
This document deals with the design and manufacture of site built, vertical, cylindrical, flat-bottomed tank systems for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -196°C.

  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 14620-4(Main)
Design and manufacture of site built, vertical, cylindrical, flat-bottomed tank systems for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -196 °C - Part 4: Insulation components
oSIST prEN 14620-4:2023

This document specifies the requirements for materials, design and installation of the insulation of refrigerated liquefied gas (RLG) storage tank systems.
RLG storage tank systems store liquefied gas with a low boiling point, i.e. below normal ambient temperature.
The concept of storing such products in liquid form and in non-pressurized tanks therefore depends on the combination of latent heat of vaporization and thermal insulation.
Consequently, thermal insulation for RLG storage tank systems is not an ancillary part of the containment system (as for most ambient atmospheric hydrocarbon tanks) but it is an essential component and the storage tank system cannot operate without a properly designed, installed and maintained insulation system.
The main functions of the insulation in RLG storage tank systems are:
-   to maintain the boil off at or below the specified limits;
-   to protect the outer tank components by maintaining them at or above their minimum design temperature;
-   to prevent damage by frost heave of the foundation/soil beneath the tank base slab (in combination with the slab heating system for tanks resting at grade);
-   to minimize condensation and icing on the outer surfaces of the tank.
A wide range of insulation materials is available. However, the material properties differ greatly amongst the various generically different materials and also within the same generic group of materials.
Therefore, within the scope of this document, only general guidance on selection of materials is given.
NOTE   For general guidance on selection of materials, see Annex A.
This document deals with the design and manufacture of site built, vertical, cylindrical, flat-bottomed tank systems for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -196 °C.

  • Draft
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day