Aerospace series - 24° interface for adaptors, threaded, with lockring - Geometric configuration

This standard specifies the dimensional characteristics of the 24° interface for adaptors, threaded, with lock-ring, assembly with elastomer O ring, for aerospace applications.
This standard applies to all adaptors, threaded, with lockring assembled to EN 2607 and used in hydraulic systems with a maximum pressure of 28 000 kPa for which a metric size coupling with a 24° conical sealing surface has been selected.

Luft- und Raumfahrt - 24° -Anschlusszapfen für gerade Einschraubverschraubungen mit Sicherungsring - Konstruktionsblatt

Diese Norm legt die Maße von 24° Anschlusszapfen für gerade Einschraubverschraubungen mit Sicherungsring und Elastomer O Ring zur Verwendung in der Luft- und Raumfahrt fest.
Diese Norm gilt für alle geraden Einschraubverschraubungen mit Sicherungsring, die nach EN 2607 aufgebaut sind und in Hydraulikanlagen mit 28 000 kPa Höchstdruck verwendet werden, für die eine metrische Verschraubung mit 24° Konus Dichtfläche gewählt wurde.

Série aérospatiale - Interface 24° pour raccords à implanter, filetés, avec bague de sécurité - Configuration géométrique

Aeronavtika – Vmesnik 24° za adapterje, z navojem, z zaklepnim obročkom – Geometrijski načrt

General Information

Status
Published
Publication Date
06-Dec-2005
Withdrawal Date
29-Jun-2006
Technical Committee
Drafting Committee
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
07-Dec-2005
Completion Date
07-Dec-2005

Buy Standard

Standard
EN 2605:2006
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - 24° interface for adaptors, threaded, with lockring - Geometric configurationSérie aérospatiale - Interface 24° pour raccords a implanter, filetés, avec bague de sécurité - Configuration géométriqueLuft- und Raumfahrt - 24° -Anschlusszapfen für gerade Einschraubverschraubungen mit Sicherungsring - KonstruktionsblattTa slovenski standard je istoveten z:EN 2605:2005SIST EN 2605:2006en49.030.99ICS:SLOVENSKI
STANDARDSIST EN 2605:200601-september-2006







EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2605
December 2005 ICS 49.030.99 English Version
Aerospace series – 24° interface for adaptors, threaded, with lockring - Geometric configuration
Série aérospatiale - Raccords droits métriques avec bague de sécurité - Interface des raccords à 24° - Dimensions
Luft- und Raumfahrt – 24° -Anschlusszapfen für gerade Einschraubverschraubungen mit Sicherungsring - Konstruktionsblatt This European Standard was approved by CEN on 28 October 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2005 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2605:2005: E



EN 2605:2005 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Required characteristics.4 4 Designation.7



EN 2605:2005 (E) 3 Foreword This European Standard (EN 2605:2005) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has re-ceived the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2006, and conflicting national standards shall be withdrawn at the latest by June 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Den-mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxem-bourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.



EN 2605:2005 (E) 4 1 Scope This standard specifies the dimensional characteristics of the 24° interface for adaptors, threaded, with lock-ring, assembly with elastomer O-ring, for aerospace applications. This standard applies to all adaptors, threaded, with lockring, assembled with EN 2607 to EN 2608 and used in hydraulic systems with a nominal pressure up to 28 000 kPa for which a metric-size coupling with a 24° conical sealing surface has been selected. 2 Normative references The following referenced documents are indisp
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.